Exhaust Flanges for 603 motor
Exhaust Flanges for 603 motor
10-08-2014, 02:49 PM
#1
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
Does anyone know where to get exhaust manifold Flanges for a 603 engine? Looking to build a new turbo manifold.
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
10-08-2014, 02:52 PM
#2
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
10-08-2014, 02:52 PM #2What's your timeframe? I can probably get some made up in a couple weeks if there is interest
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
10-08-2014, 04:03 PM
#3
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
Yeah much more then a couple of weeks and I may get impatent. I can have my normal guy make them but he can only do 1/4 inch at this point.
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
10-08-2014, 09:45 PM
#4
raysorenson
10-08-2014, 09:45 PM #4I'm interested. I've got a 602 and a 603 I'd like to build headers for. How thick?
10-08-2014, 11:12 PM
#5
Rusty
RustyLugNut
10-08-2014, 11:12 PM #5I can provide the required flanges if you can send me accurate profiles of the gasket area. I can mill up to 5/8 inch in thickness if needed.
Rusty
10-09-2014, 07:07 AM
#6
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
Would an exhaust manifold gasket work? What kinda cost and time are you thinking?
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
10-09-2014, 10:45 AM
#7
(10-09-2014, 07:07 AM)TurboTim Would an exhaust manifold gasket work? What kinda cost and time are you thinking?
6 cylinder flanges cost about 150 USD (Cummins). It would take roughly a week to slip it into the work flow and ship it out. If we could get several pieces made, it would reduce the individual costs somewhat.
A manifold gasket would be ideal.
Rusty
RustyLugNut
10-09-2014, 10:45 AM #7(10-09-2014, 07:07 AM)TurboTim Would an exhaust manifold gasket work? What kinda cost and time are you thinking?
6 cylinder flanges cost about 150 USD (Cummins). It would take roughly a week to slip it into the work flow and ship it out. If we could get several pieces made, it would reduce the individual costs somewhat.
A manifold gasket would be ideal.
Rusty
10-09-2014, 12:58 PM
#8
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
Lets do it. What do you need from me? Can I get your number?
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
10-09-2014, 01:32 PM
#9
I see other OM603 flanges use a 40.5mm port diameter.
raysorenson
10-09-2014, 01:32 PM #9And I need 1 for a 602 and one for a 603. 5 cyl discount? =).
I see other OM603 flanges use a 40.5mm port diameter.
10-09-2014, 03:34 PM
#10
http://shop.klracing.se/sv/artiklar/flan...-10mm.html
raysorenson
10-09-2014, 03:34 PM #10You can get flanges from Sweden for 450 Krona. ~65 USD. Shipping might suck. You want to go in on a buy TurboTim? Anyone else?
http://shop.klracing.se/sv/artiklar/flan...-10mm.html
10-10-2014, 07:42 AM
#11
(10-09-2014, 03:34 PM)raysorenson You can get flanges from Sweden for 450 Krona. ~65 USD. Shipping might suck. You want to go in on a buy TurboTim? Anyone else?
http://shop.klracing.se/sv/artiklar/flan...-10mm.html
+1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Duncansport
10-10-2014, 07:42 AM #11(10-09-2014, 03:34 PM)raysorenson You can get flanges from Sweden for 450 Krona. ~65 USD. Shipping might suck. You want to go in on a buy TurboTim? Anyone else?
http://shop.klracing.se/sv/artiklar/flan...-10mm.html
+1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
10-10-2014, 10:17 AM
#12
(10-09-2014, 12:58 PM)TurboTim Lets do it. What do you need from me? Can I get your number?
I'll send you a PM with contact information.
Raysorenson. If you want to get in on this, we can oblige the 5 cylinder 602.
Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
RustyLugNut
10-10-2014, 10:17 AM #12(10-09-2014, 12:58 PM)TurboTim Lets do it. What do you need from me? Can I get your number?
I'll send you a PM with contact information.
Raysorenson. If you want to get in on this, we can oblige the 5 cylinder 602.
Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
10-11-2014, 12:43 PM
#13
raysorenson
10-11-2014, 12:43 PM #13I'm going to see how it pans out with KL racing. Thank you and simpler for the offer to make these.
10-16-2014, 04:00 AM
#14
(10-10-2014, 07:42 AM)Duncansport +1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
(10-10-2014, 10:17 AM)RustyLugNut Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
(10-10-2014, 07:42 AM)Duncansport +1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
(10-10-2014, 10:17 AM)RustyLugNut Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
10-16-2014, 07:24 AM
#15
(10-16-2014, 04:00 AM)mbz123(10-10-2014, 07:42 AM)Duncansport +1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
(10-10-2014, 10:17 AM)RustyLugNut Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
$154.00 shipped to my shop
Duncansport
10-16-2014, 07:24 AM #15(10-16-2014, 04:00 AM)mbz123(10-10-2014, 07:42 AM)Duncansport +1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
(10-10-2014, 10:17 AM)RustyLugNut Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
$154.00 shipped to my shop
10-17-2014, 10:50 AM
#16
(10-16-2014, 07:24 AM)Duncansport(10-16-2014, 04:00 AM)mbz123(10-10-2014, 07:42 AM)Duncansport +1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
(10-10-2014, 10:17 AM)RustyLugNut Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
$154.00 shipped to my shop
TY
I'm thinking quanities could be belted out once/twice a year and offered at almost half that amount. Just what a diy'er on the cheap needs.
MBZ123
(10-16-2014, 07:24 AM)Duncansport(10-16-2014, 04:00 AM)mbz123(10-10-2014, 07:42 AM)Duncansport +1 on this, ive bought two OM605 flanges from them. Part was at my shop in about 1 week.
Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
(10-10-2014, 10:17 AM)RustyLugNut Price is dependent on specifications of course. If you just want the 9-10 mm flange, that does reduce the costs.
Rusty.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
$154.00 shipped to my shop
TY
I'm thinking quanities could be belted out once/twice a year and offered at almost half that amount. Just what a diy'er on the cheap needs.
MBZ123
10-17-2014, 11:38 AM
#17
Duncansport
10-17-2014, 11:38 AM #17i think most will need 2-3 flanges when attempting their own header/manifolds
10-17-2014, 04:33 PM
#18
(10-17-2014, 11:38 AM)Duncansport i think most will need 2-3 flanges when attempting their own header/manifolds
Haha. That's the last part you weld too. After pricing all the stuff and considering the time involved, Fred's headers are starting to look reasonably priced.
raysorenson
10-17-2014, 04:33 PM #18(10-17-2014, 11:38 AM)Duncansport i think most will need 2-3 flanges when attempting their own header/manifolds
Haha. That's the last part you weld too. After pricing all the stuff and considering the time involved, Fred's headers are starting to look reasonably priced.
10-21-2014, 02:30 AM
#20
(10-17-2014, 10:50 AM)mbz123(10-16-2014, 07:24 AM)Duncansport(10-16-2014, 04:00 AM)mbz123 Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
$154.00 shipped to my shop
TY
I'm thinking quanities could be belted out once/twice a year and offered at almost half that amount. Just what a diy'er on the cheap needs.
MBZ123
I think this is a good idea. I will look into a 3/8 inch flange in mild steel and a batch run. That should bring the prices down under 100 USD for forum members. I will do the 603 engine first as there seems to be more interest at this time. I will look into other engines as we move forward.
Rusty
RustyLugNut
10-21-2014, 02:30 AM #20(10-17-2014, 10:50 AM)mbz123(10-16-2014, 07:24 AM)Duncansport(10-16-2014, 04:00 AM)mbz123 Mind commenting on the actual shipping charges? Looking for a total to your doorstep.
I'd be in for a couple 603 flanges. If we can get enough momentum here, it would best the alternatives mentioned + s&h. Care to break down some price points for us?
10mm mild steel @ X(qty)=$Y
Not sure if thicker is necessary, is it? Different material? A sub hundred dollar piece would ROCK
Have a gasket to contribute to the cause, too.
MBZ123
$154.00 shipped to my shop
TY
I'm thinking quanities could be belted out once/twice a year and offered at almost half that amount. Just what a diy'er on the cheap needs.
MBZ123
I think this is a good idea. I will look into a 3/8 inch flange in mild steel and a batch run. That should bring the prices down under 100 USD for forum members. I will do the 603 engine first as there seems to be more interest at this time. I will look into other engines as we move forward.
Rusty
10-21-2014, 07:04 AM
#21
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
I got a 606 gasket and the 603 gasket should be here today and I will send them off to you right away.
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
10-21-2014, 10:29 AM
#22
http://www.superturbodiesel.com/std/Thre...mounts-etc
...you have the om606 flange posted by me. Also fits 605 and 604.
Missed a couple of numbers while doing it, but that's commented on and I wrote it in a post further down.
F-tune Performance
![[Image: V-band_om606.jpg]](http://www.f-tune.se/wp-content/uploads/2015/01/V-band_om606.jpg)
![[Image: GTX3582R.jpg]](http://www.f-tune.se/wp-content/uploads/2015/01/GTX3582R.jpg)
![[Image: gs6-53dz_gearbox.jpg]](http://www.f-tune.se/wp-content/uploads/2015/01/gs6-53dz_gearbox.jpg)
I can help you out with all your manual transmission, clutch, flywheel, intake and exhaust manifold issues.
Here...
http://www.superturbodiesel.com/std/Thre...mounts-etc
...you have the om606 flange posted by me. Also fits 605 and 604.
Missed a couple of numbers while doing it, but that's commented on and I wrote it in a post further down.
F-tune Performance
I can help you out with all your manual transmission, clutch, flywheel, intake and exhaust manifold issues.
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Users browsing this thread:
1 Guest(s)
1 Guest(s)