STD
Big Garrett Turbo - Printable Version

+- STD (https://www.superturbodiesel.com/std)
+-- Forum: Tuning (https://www.superturbodiesel.com/std/forumdisplay.php?fid=6)
+--- Forum: Engine (https://www.superturbodiesel.com/std/forumdisplay.php?fid=7)
+--- Thread: Big Garrett Turbo (/showthread.php?tid=4422)

Big Garrett Turbo - TheDon - 03-16-2013

So I had to leave the junkyard with this today

[Image: 205259_10151277634696534_81385152_n.jpg]

It's probably too big for my 606 even if I went full on superturbo

It has no shaft play and spins freely plus it has a factory rebuilt plate on it.

I think I need to pull the housings and measure the compressor wheel and turbine and see what I have. I probably is waaaaay to big for my 606, the thing came off of a Detroit Diesel cylinder

RE: Big Garrett Turbo - TheDon - 03-18-2013

So I believe this is some form of GT4202R and I found a compressor map

[img]http://www.himni-racing.com/index.php?main_page=popup_image&pID=1859&zenid=k3j1s6fdd5nd0tou9sckc5ioo0[\img]

I really do wonder if this thing is useable if I go full on super turbo. Forged rods, massive inter cooler, etc

RE: Big Garrett Turbo - EDH_Performance - 03-18-2013

Take off the cover and measure the in/exducerWink It looks like a very good suited superturbo, but spool depends on how big the exhaust housing isWink

RE: Big Garrett Turbo - TheDon - 03-18-2013

The exhaust housing is large. It's off of a Semi truck engine. Plus it has no waste gate.

http://www.full-race.com/store/turbos/garrett-gt-series/garrett-gt4202r-twinscroll-turbo.html

[Image: garrett-gt4202r-twinscroll-turbo-content-1.jpg]

I do not think the OM606 can pump this thing up, I think.

I swear I've seen a build here where the person used a Scania turbocharger


The inducer is : 65mm
Exducer is: 90mm

RE: Big Garrett Turbo - Simpler=Better - 03-18-2013

Maybe a twin 606 car?

RE: Big Garrett Turbo - w123love - 03-18-2013

(03-18-2013, 10:08 AM)TheDon I swear I've seen a build here where the person used a Scania turbocharger

BSR originally used a Scania turbine

RE: Big Garrett Turbo - led-panzer - 03-19-2013

If the exducer is 90mm it's not a 4202 (102mm compressor wheel)

RE: Big Garrett Turbo - TheDon - 03-19-2013

Then what is it then, any idea?

RE: Big Garrett Turbo - EDH_Performance - 03-26-2013

(03-19-2013, 04:52 PM)TheDon Then what is it then, any idea?

Gt4088 or similar maybe...
(03-19-2013, 04:52 PM)TheDon Then what is it then, any idea?

Gt4088 or similar maybe...

RE: Big Garrett Turbo - MFSuper90 - 03-26-2013

TV4502 actually
Compressor wheel 64/92
Turbine wheel 82mm (all the way)

If the big sloppy exhaust housing was swapped for a smaller t4 .9 or something it would be a good atmospheric charger in a compound setup

RE: Big Garrett Turbo - dieselboy - 03-26-2013

I have a gt4082klnv that's looking for a home.
[Image: 2B651AD1-6585-4EDF-A237-73A14C384690-123...e84a55.jpg]

RE: Big Garrett Turbo - TheDon - 03-26-2013

nah, I kind of wish I didn't buy the stupid thing now.

RE: Big Garrett Turbo - MFSuper90 - 03-26-2013

(03-26-2013, 05:39 PM)dieselboy I have a gt4082klnv that's looking for a home.
[Image: 2B651AD1-6585-4EDF-A237-73A14C384690-123...e84a55.jpg]

Been sucking in some soot?
Compressor looks a lil black

RE: Big Garrett Turbo - HaavardPYA - 03-27-2013

My GT42 got "GT42" stamped on the number plate that sits just besides the oil feed line hole. Its from a Volvo truck.

RE: Big Garrett Turbo - dieselboy - 03-27-2013

(03-26-2013, 09:59 PM)MFSuper90
(03-26-2013, 05:39 PM)dieselboy I have a gt4082klnv that's looking for a home.
[IMG]http://i1225.photobucket.com/albums/ee390/dieselboy73/2B651AD1-6585-4EDF-A237-73A14C384690-12393-00000DDA20888776_zps0be84a5

Been sucking in some soot?
Compressor looks a lil black

I pulled it from a ud (Nissan) truck. 2007 7.2l I6 The motor in the vnt controller died and they don't sell it separately.

The compressor has oil film from the crank case vent system. They don't do road draft tubes anymore.

[Image: E024AC4C-F069-4631-9783-DCC3C74C1768-123...2b5275.jpg]

RE: Big Garrett Turbo - MFSuper90 - 03-27-2013

So the only thing wrong is the controller?
Do you know specs on that turbo? I can't seem to find them.

RE: Big Garrett Turbo - HaavardPYA - 05-24-2013

Would this gt42 be a good turbo in an compound setup with an hx35?

RE: Big Garrett Turbo - offroaddieselhu - 05-29-2013

Hi,

If the gt4082klnv is catchable in god price I would built on an 6 cylinder engine! Smile

Offoraddieselhu

RE: Big Garrett Turbo - majesty78 - 05-29-2013

With a little playing around you can make it a mechanical VNT turbo, using a conventional push type wastegate actuator.

Or convert it to vacuum pull type VNT actuator for EDC application....

If it wouldn't be located in US, I would buy it ^^

RE: Big Garrett Turbo - offroaddieselhu - 05-29-2013

it is the soul of VGT turbo https://www.youtube.com/watch?v=u74Ofbgjaoc

RE: Big Garrett Turbo - swecias - 05-30-2013

(05-24-2013, 05:21 PM)HaavardPYA Would this gt42 be a good turbo in an compound setup with an hx35?

that will be good setup for high power Smile