STD Maintenance General OM617 IP

OM617 IP

OM617 IP

 
  • 0 Vote(s) - 0 Average
 
cjcosta
TA 0301

51
03-09-2011, 06:23 AM #1
Hello everyone,

I am almost finnishing a swap in my w460.
The motor is a 617A (617952)

Anyone have the vacuum connections and electrical valves (temp oil pressure etc) scheme?

Best Regards,

Carlos

cjcosta
03-09-2011, 06:23 AM #1

Hello everyone,

I am almost finnishing a swap in my w460.
The motor is a 617A (617952)

Anyone have the vacuum connections and electrical valves (temp oil pressure etc) scheme?

Best Regards,

Carlos

aaa
GT2256V

913
03-09-2011, 09:09 PM #2
What kind of swap? The manual trans vacuum connections are quite few. What did it have before?
aaa
03-09-2011, 09:09 PM #2

What kind of swap? The manual trans vacuum connections are quite few. What did it have before?

cjcosta
TA 0301

51
03-10-2011, 01:14 PM #3
Manual trans swap
Well the motor is running, try and error was the solution.

Thanks aaa.

Now i need some hel with the gauges, i intend to install: Oil pressure, rpm, water temp and turbo press.

Best Regards,

Carlos
cjcosta
03-10-2011, 01:14 PM #3

Manual trans swap
Well the motor is running, try and error was the solution.

Thanks aaa.

Now i need some hel with the gauges, i intend to install: Oil pressure, rpm, water temp and turbo press.

Best Regards,

Carlos

aaa
GT2256V

913
03-10-2011, 04:24 PM #4
Use the same ones from before? There's not much to wire. Oil pressure was a hose with oil in it to the instrument cluster, is that what it used before? Temperature was one wire, the sensor is next to the glowplugs. Turbo pressure is something you create yourself.
aaa
03-10-2011, 04:24 PM #4

Use the same ones from before? There's not much to wire. Oil pressure was a hose with oil in it to the instrument cluster, is that what it used before? Temperature was one wire, the sensor is next to the glowplugs. Turbo pressure is something you create yourself.

cjcosta
TA 0301

51
03-14-2011, 05:27 PM #5
I am with a small problem in the new engine.
After a few hours resting the motor runs without power for a minute or two, after that the power comes back.
I think its possible the injection system is not ok (maybe a leak), i have changed the manual pump for the one in the old motor and i suspect a part is missing ( a small plastic red/black pin ).
Anyone have a scheme of the manual vacuum pump?

cjcosta
03-14-2011, 05:27 PM #5

I am with a small problem in the new engine.
After a few hours resting the motor runs without power for a minute or two, after that the power comes back.
I think its possible the injection system is not ok (maybe a leak), i have changed the manual pump for the one in the old motor and i suspect a part is missing ( a small plastic red/black pin ).
Anyone have a scheme of the manual vacuum pump?

winmutt
bitbanger

3,468
03-17-2011, 04:11 PM #6
I do not have a schematic but its pretty easy to rebuild and the rebuild kit is cheap. It sounds more like you have air in the system?

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
03-17-2011, 04:11 PM #6

I do not have a schematic but its pretty easy to rebuild and the rebuild kit is cheap. It sounds more like you have air in the system?


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 2 Guest(s)
Users browsing this thread:
 2 Guest(s)