STD
Just pulled my 722.633 - Printable Version

+- STD (https://www.superturbodiesel.com/std)
+-- Forum: Tuning (https://www.superturbodiesel.com/std/forumdisplay.php?fid=6)
+--- Forum: Drivetrain (https://www.superturbodiesel.com/std/forumdisplay.php?fid=9)
+--- Thread: Just pulled my 722.633 (/showthread.php?tid=6031)



Just pulled my 722.633 - TurboTim - 12-05-2014

So I just pulled a 722.633 out of a 2001 S500. I have an OM606 on order and it should be here in a week. I am swapping these into my 87 300SDL. The question I have is how hard is the bell housing to swap? Do you just pull the converter out and unbolt it from there or do the internals have to come out? Im super excited to have a trans that can actual hold the power! 5 speed too!


RE: Just pulled my 722.633 - Duncansport - 12-06-2014

Its not hard really just a bit involved. The trans case lifts off the gear set leaving the gears and clutch attached to the bell housing. ONce its disassembled just swap the stuff over.


RE: Just pulled my 722.633 - TurboTim - 12-06-2014

Anything hard to line up or anything? or tips?


RE: Just pulled my 722.633 - Duncansport - 12-08-2014

Its fairly easy. here are a few places to view the ATSG manual for the 722.6 http://www.all-trans.by/assets/site/files/722.6.pdf


RE: Just pulled my 722.633 - barrote - 12-09-2014

yelloo
speaking about auto trans 722.6, does anyone knows where can i find a repair manual ??


RE: Just pulled my 722.633 - Duncansport - 12-10-2014

(12-09-2014, 01:24 PM)barrote yelloo
speaking about auto trans 722.6, does anyone knows where can i find a repair manual ??

Just google ATSG 722.6. There out there everywhere in PDF


RE: Just pulled my 722.633 - TurboTim - 12-11-2014

Isn't that what you posted?


RE: Just pulled my 722.633 - barrote - 12-11-2014

i´l try , been searching for a wile now and nothing.
have anyone converted one of this to mechanichal shape?
thanks ,
regards


RE: Just pulled my 722.633 - raysorenson - 12-11-2014

I've found some info on the 722.6 at sonnax.com. You can probably buy repair info there.


RE: Just pulled my 722.633 - barrote - 12-12-2014

buy!!!! thanks ,
i can also send the gearbox to a repair shop ;D


RE: Just pulled my 722.633 - TurboTim - 12-12-2014

So for some dumb reason I though my 87 SDL transmission would work and my motor should be here tomorrow. If get a transmission out of a C230 will that work. Car-part lists it as a 722.600 and says it will work for a 97 E300D. Thoughts? Are the gas motor bellhousing swap with the dizzels because Car-part seems to think so.


RE: Just pulled my 722.633 - raysorenson - 12-13-2014

The inline engines have the same bell hsg bolt pattern.


RE: Just pulled my 722.633 - TurboTim - 12-13-2014

I just picked up that C230 transmission. I was thinking about using the tq converter from it. It looks a little smaller and should help my HX40 spool a bit better. Anyone have any reason against that?

I did swap the internals and it was more stuff then I wanted to move over but not a problem at all. Just got the trans pulled out of the SDL now am pulling the motor.