STD Other Projects Roscoe rides again, om601 into '84 Ranger swap

Roscoe rides again, om601 into '84 Ranger swap

Roscoe rides again, om601 into '84 Ranger swap

 
  • 0 Vote(s) - 0 Average
 
sassparilla_kid
diesel > all other fuels

1,618
03-20-2016, 10:03 PM #1
Howdy y'all, havent posted in a while but I'm planning on starting a new project soon and figured I might as well get a thread started on it. The plan is to swap the om601 (2.2) from my dad's 190D (he mostly drives his MX5 now and the w201 is just sitting), into our 1984 Ford Ranger (Roscoe). As some of you may know, I bought an '86 Toyota 4x4 pickup (factory turbo 22rte) last fall and have mostly been driving it around, as its a little handier around the ranch where I work haha. However, this gas engine nonsense isn't really for me, and I think it's time for a diesel pickup. Ideally I'd swap a turbo om602 into the Toyota, or even a 1.9tdi (either may happen eventually), but that would mean having no truck to drive in the meantime, and I don't have either of those engines laying around. I do have a 601 though, and the Ranger to swap it into, and the skills (is like to think so anyway) to make it happen. I'm hoping to get the engines pulled this week so I can start comparing them. The om601 has a 5-speed (5th overdrive, I forget the model number) mated to it, and the Ford ll23 has a Toyo Kogyo tk5 (again, 5-speed, 5th overdrive) mated to it.  I've done some research and compared gear spreads on them, not too much difference between them, the Ford has 3.73 rear gears, I'm guessing the w201 is close to that (from what I've read it could be 3.23 or 3.91, I guess they changed in 1985 along with the gear spread in the trans, not sure what month our car is), so I'm not too worried about gearing being an issue. From my initial measurements, it looks like there is enough room for the 601 to fit,  although I'm not sure yet if there will be any clearance issues with the cross member or not.

   
Donor engine

   
Donor car

   
Old ford gasser

   
Recipeint truck (Roscoe)

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
03-20-2016, 10:03 PM #1

Howdy y'all, havent posted in a while but I'm planning on starting a new project soon and figured I might as well get a thread started on it. The plan is to swap the om601 (2.2) from my dad's 190D (he mostly drives his MX5 now and the w201 is just sitting), into our 1984 Ford Ranger (Roscoe). As some of you may know, I bought an '86 Toyota 4x4 pickup (factory turbo 22rte) last fall and have mostly been driving it around, as its a little handier around the ranch where I work haha. However, this gas engine nonsense isn't really for me, and I think it's time for a diesel pickup. Ideally I'd swap a turbo om602 into the Toyota, or even a 1.9tdi (either may happen eventually), but that would mean having no truck to drive in the meantime, and I don't have either of those engines laying around. I do have a 601 though, and the Ranger to swap it into, and the skills (is like to think so anyway) to make it happen. I'm hoping to get the engines pulled this week so I can start comparing them. The om601 has a 5-speed (5th overdrive, I forget the model number) mated to it, and the Ford ll23 has a Toyo Kogyo tk5 (again, 5-speed, 5th overdrive) mated to it.  I've done some research and compared gear spreads on them, not too much difference between them, the Ford has 3.73 rear gears, I'm guessing the w201 is close to that (from what I've read it could be 3.23 or 3.91, I guess they changed in 1985 along with the gear spread in the trans, not sure what month our car is), so I'm not too worried about gearing being an issue. From my initial measurements, it looks like there is enough room for the 601 to fit,  although I'm not sure yet if there will be any clearance issues with the cross member or not.

   
Donor engine

   
Donor car

   
Old ford gasser

   
Recipeint truck (Roscoe)


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

raysorenson
Superturbo

1,162
03-21-2016, 07:31 PM #2
Some of the text on the rh side is cut off and I can't scroll L to R. Looks interesting.
raysorenson
03-21-2016, 07:31 PM #2

Some of the text on the rh side is cut off and I can't scroll L to R. Looks interesting.

sassparilla_kid
diesel > all other fuels

1,618
03-21-2016, 11:14 PM #3
Yeah its a problem with the forum I think, I'll try to resize the pictures next time I'm on a computer

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
03-21-2016, 11:14 PM #3

Yeah its a problem with the forum I think, I'll try to resize the pictures next time I'm on a computer


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

benzguy
GT2256V

124
02-28-2018, 07:46 AM #4
Any update on this project ?
benzguy
02-28-2018, 07:46 AM #4

Any update on this project ?

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)