om606 G Starting problems
om606 G Starting problems
i'm new here so bare with me
i recently completed my om606 8mm pump with hx35w project
i got the pump from Dpumpuk and also the exhaust manifold
runs great pulls like a dream whit a g250 manual trans (i know it will not hold for long)
used the clutch of the same car had the disc layed with copper
now here is the problem
when i start it starts very nicely but after 5seconds it dies
and to restart it takes a lot glowing and starting to get it running again
any thoughts ?
sorry for my bad english i'm from belgium
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
hello
i'm new here so bare with me
i recently completed my om606 8mm pump with hx35w project
i got the pump from Dpumpuk and also the exhaust manifold
runs great pulls like a dream whit a g250 manual trans (i know it will not hold for long)
used the clutch of the same car had the disc layed with copper
now here is the problem
when i start it starts very nicely but after 5seconds it dies
and to restart it takes a lot glowing and starting to get it running again
any thoughts ?
sorry for my bad english i'm from belgium
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
2nd question: where in BE do you live?
Evgeniy1987
09-27-2016, 04:25 AM #2And... When it runs again.. does it run well ?
2nd question: where in BE do you live?
(Heerlen - Turnhout is 110 km.. we might visit each other one day)
Evgeniy1987
09-27-2016, 01:19 PM #4For me.. it is like you are having a minor leak somewhere, and then get some air in your system.
(Heerlen - Turnhout is 110 km.. we might visit each other one day)
a 0.55 mm banjo bolt at the return from the pump to cause internal pressure in the pump...
Not that you accidentally mounted a wrong one or a too big one or something ?
Would is be easy for you to try it with an electrical pump ? Just to be sure that the mechanical lift pump is not the problem. (if you don't have it already)
Evgeniy1987
09-27-2016, 01:58 PM #6I am not very sure whether the inline-pumps have it, but the VP in my Scirocco has it:
a 0.55 mm banjo bolt at the return from the pump to cause internal pressure in the pump...
Not that you accidentally mounted a wrong one or a too big one or something ?
Would is be easy for you to try it with an electrical pump ? Just to be sure that the mechanical lift pump is not the problem. (if you don't have it already)
but no change i also have instaled a presure valve on the return line right after the banjo bolt
it opens at 1.2bar again no change
by electrical pump u meen the lift pump of the elec pump ?
i have switched out the mech lift pump (whit the hose fitting and treads)
had a spare one sitting on a 603mech pump but again no change
was thinking of instaling a lift pump at the tank as its the 463tank (plastic) it has the mounts to place one from the 230ge and i have a lift pump some where :p
i'll try that see if it helps or not
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
it does have a presure banjo bolt have replaced it already dpumpuk thought that was the problem too
but no change i also have instaled a presure valve on the return line right after the banjo bolt
it opens at 1.2bar again no change
by electrical pump u meen the lift pump of the elec pump ?
i have switched out the mech lift pump (whit the hose fitting and treads)
had a spare one sitting on a 603mech pump but again no change
was thinking of instaling a lift pump at the tank as its the 463tank (plastic) it has the mounts to place one from the 230ge and i have a lift pump some where :p
i'll try that see if it helps or not
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
Not your shutoff actuator line connecting to vacuum is it....I did that yesterday...woops
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
(09-27-2016, 06:31 PM)NZScott Not your shutoff actuator line connecting to vacuum is it....I did that yesterday...woops
have done that before too :p not the case this time
have instaled the electronic feed pump at the tank i have too turn in on/off manual but thats even worse ??
so i turn on the pump glow and start it fires up and dies after a bit not to start again ....... let is sit for an hour
and i can try again so then i started expirementing turn on the pump glow start when it runs turn of the pump and it struggels a litle and then it runs smooth......
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
(09-27-2016, 06:31 PM)NZScott Not your shutoff actuator line connecting to vacuum is it....I did that yesterday...woops
have done that before too :p not the case this time
have instaled the electronic feed pump at the tank i have too turn in on/off manual but thats even worse ??
so i turn on the pump glow and start it fires up and dies after a bit not to start again ....... let is sit for an hour
and i can try again so then i started expirementing turn on the pump glow start when it runs turn of the pump and it struggels a litle and then it runs smooth......
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
if you set the 2 vacccum lines wrong it will do that.
Try remove the small vaccum line on the stop and see if there is any difference..
do you have 100% banjo or plastic o-ring fuel lines? as 605/606 standard?
Do you have a ingnitonkey operated stop vaccum?
if you set the 2 vacccum lines wrong it will do that.
Try remove the small vaccum line on the stop and see if there is any difference..
do you have 100% banjo or plastic o-ring fuel lines? as 605/606 standard?
(10-03-2016, 01:15 PM)wouter the ingnition din't have a vaccum shut off so i used a electronic valve that opens when u turn the key
whit 100% banjo what do u mean by that all fuel lines ar rubber no plastic lines
ok, do try to start with the vaccum hose disconnected from the stop on pump.
did you replace whole fuelfilter holder and all fuel connectors to 603 style with banjo fittings?
if not its wery common that there is a air leak in those plastic connectors an fuel will drain when car is sitting over night.
i have had that trubble on a 605 before.
(10-03-2016, 01:15 PM)wouter the ingnition din't have a vaccum shut off so i used a electronic valve that opens when u turn the key
whit 100% banjo what do u mean by that all fuel lines ar rubber no plastic lines
ok, do try to start with the vaccum hose disconnected from the stop on pump.
did you replace whole fuelfilter holder and all fuel connectors to 603 style with banjo fittings?
if not its wery common that there is a air leak in those plastic connectors an fuel will drain when car is sitting over night.
i have had that trubble on a 605 before.
-------------------------------------------------------------------------------------------------------------------------
Ex: 525tds 130kW, C250TD 160kW, E320CDI 200kW, ML400CDI 230kW, A6 R5TDI 130kW
Now: Q7 V8TDI 240kW, 320d 150kW, 335d 210kW
But when it runs and you drive it, then you start it in lets say hour or two it goes good? This sounds to me like major diesel leak. Over night fuel goes from IP back into tank, when you try to start it will burn last remnants caught in elements and then it is good known story of M pump filled with air.. takes a loooot of cranking. No one-way valves will help you with this as it can leak to tank via fuel return. You need to reseal whole injection system, electric lift pump is always good idea.
-------------------------------------------------------------------------------------------------------------------------
Ex: 525tds 130kW, C250TD 160kW, E320CDI 200kW, ML400CDI 230kW, A6 R5TDI 130kW
Now: Q7 V8TDI 240kW, 320d 150kW, 335d 210kW
it does have a check valve right after the tank
and i instaled a electric lift pump thats even worse? if i let the pump on it dies
what i do to start is now turn the electric lift pump on for 4 seconds then glow for about 6seconds and the start it doesn't work evry time
if i let the electric lift pump on it start and dies again too ? even if im driving i turn it on it dies??
.
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
if i stop the engine for longer that 20/30min it doest it again
it does have a check valve right after the tank
and i instaled a electric lift pump thats even worse? if i let the pump on it dies
what i do to start is now turn the electric lift pump on for 4 seconds then glow for about 6seconds and the start it doesn't work evry time
if i let the electric lift pump on it start and dies again too ? even if im driving i turn it on it dies??
.
1986 g om606 hx35 DpumpUk 8mm pump
1991 300ge on lpg
When you disconnect hose at injector pump and then run electric pump does the fuel pours out? When the engine is running do you see airbubles in transparent lines?
-------------------------------------------------------------------------------------------------------------------------
Ex: 525tds 130kW, C250TD 160kW, E320CDI 200kW, ML400CDI 230kW, A6 R5TDI 130kW
Now: Q7 V8TDI 240kW, 320d 150kW, 335d 210kW
Well.. stupid thing but did you mount that electric pump right way? When you disconnect hose at injector pump and then run electric pump does the fuel pours out? When the engine is running do you see airbubles in transparent lines?
-------------------------------------------------------------------------------------------------------------------------
Ex: 525tds 130kW, C250TD 160kW, E320CDI 200kW, ML400CDI 230kW, A6 R5TDI 130kW
Now: Q7 V8TDI 240kW, 320d 150kW, 335d 210kW
1 Guest(s)
1 Guest(s)