STD Tuning Engine Garrett 712120 VNT Hella 6NW 008 412 actuator.

Garrett 712120 VNT Hella 6NW 008 412 actuator.

Garrett 712120 VNT Hella 6NW 008 412 actuator.

 
  • 2 Vote(s) - 5 Average
 
Pages (4): Previous 1 2 3 4
Iangiulu
Naturally-aspirated

2
07-12-2014, 02:42 PM #151
(07-10-2014, 02:06 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

No one?
Iangiulu
07-12-2014, 02:42 PM #151

(07-10-2014, 02:06 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

No one?

Darqs
Naturally-aspirated

15
12-18-2014, 03:06 AM #152
(07-12-2014, 02:42 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

Yes... if only PWM freq=140Hz.

Best regards,
Darqs
Darqs
12-18-2014, 03:06 AM #152

(07-12-2014, 02:42 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

Yes... if only PWM freq=140Hz.

Best regards,
Darqs

antonmies
Go MPR

59
01-23-2015, 06:43 AM #153
What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...
This post was last modified: 01-23-2015, 06:53 AM by antonmies.
antonmies
01-23-2015, 06:43 AM #153

What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

HoleshotHolset
Holset

379
04-15-2015, 10:37 AM #154
(01-23-2015, 06:43 AM)antonmies What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

The leads are spot welded from the factory.
I tried soldering these using rosin core solder and flux and did not have any luck.

Attached is a picture of a rather poor attempt at fixing the leads on a "good used" actuator I bought from a gent on another forum.

Beers,


Matt
Attached Files
Image(s)
   

'07 W211 OM642
'95 W124.131/722.435, 211k - daily driver/Superturbo project - OM606.962 with "M" pump...under construction! (build thread here)
'99 W210.025 - gone, but not forgotten
'94 Dodge/Cummins - gone, but not forgotten
HoleshotHolset
04-15-2015, 10:37 AM #154

(01-23-2015, 06:43 AM)antonmies What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

The leads are spot welded from the factory.
I tried soldering these using rosin core solder and flux and did not have any luck.

Attached is a picture of a rather poor attempt at fixing the leads on a "good used" actuator I bought from a gent on another forum.

Beers,


Matt

Attached Files
Image(s)
   

'07 W211 OM642
'95 W124.131/722.435, 211k - daily driver/Superturbo project - OM606.962 with "M" pump...under construction! (build thread here)
'99 W210.025 - gone, but not forgotten
'94 Dodge/Cummins - gone, but not forgotten

Pages (4): Previous 1 2 3 4
 
  • 2 Vote(s) - 5 Average
Users browsing this thread:
 5 Guest(s)
Users browsing this thread:
 5 Guest(s)