Garrett 712120 VNT Hella 6NW 008 412 actuator.

STD Tuning Engine Garrett 712120 VNT Hella 6NW 008 412 actuator.

Garrett 712120 VNT Hella 6NW 008 412 actuator.

Garrett 712120 VNT Hella 6NW 008 412 actuator.

View a Printable Version

2 Vote(s) - 5 Average

Pages (4): Previous 1 2 3 4

Iangiulu

Naturally-aspirated

2

07-12-2014, 02:42 PM #151

(07-10-2014, 02:06 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

No one?

Iangiulu

07-12-2014, 02:42 PM #151

(07-10-2014, 02:06 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

No one?

Darqs

Naturally-aspirated

15

12-18-2014, 03:06 AM #152

(07-12-2014, 02:42 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

Yes... if only PWM freq=140Hz.

Best regards,
Darqs

Darqs

12-18-2014, 03:06 AM #152

(07-12-2014, 02:42 PM)Iangiulu Hi, I need your help. Did you know if this is working for the MB actuator?

Yes... if only PWM freq=140Hz.

Best regards,
Darqs

antonmies

Go MPR

59

01-23-2015, 06:43 AM #153

What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

This post was last modified: 01-23-2015, 06:53 AM by antonmies.

Master Power MPR high performance turbochargers

antonmies

01-23-2015, 06:43 AM #153

What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

Master Power MPR high performance turbochargers

Holset

379

04-15-2015, 10:37 AM #154

(01-23-2015, 06:43 AM)antonmies What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

The leads are spot welded from the factory.
I tried soldering these using rosin core solder and flux and did not have any luck.

Attached is a picture of a rather poor attempt at fixing the leads on a "good used" actuator I bought from a gent on another forum.

Beers,

Matt

Attached Files

Image(s)

'07 W211 OM642
'95 W124.131/722.435, 211k - daily driver/Superturbo project - OM606.962 with "M" pump...under construction! (build thread here)
'99 W210.025 - gone, but not forgotten
'94 Dodge/Cummins - gone, but not forgotten

HoleshotHolset

04-15-2015, 10:37 AM #154

(01-23-2015, 06:43 AM)antonmies What type of soldering there is in the leads from the PCB to housing?
There is a broken lead in a servo I'm trying to fix, but the solder I use doesn't seem to stick. Just floats on the surface as a metal ball...

The leads are spot welded from the factory.
I tried soldering these using rosin core solder and flux and did not have any luck.

Attached is a picture of a rather poor attempt at fixing the leads on a "good used" actuator I bought from a gent on another forum.

Beers,

Matt

Attached Files

Image(s)

'07 W211 OM642
'95 W124.131/722.435, 211k - daily driver/Superturbo project - OM606.962 with "M" pump...under construction! (build thread here)
'99 W210.025 - gone, but not forgotten
'94 Dodge/Cummins - gone, but not forgotten

Pages (4): Previous 1 2 3 4

View a Printable Version

2 Vote(s) - 5 Average

Users browsing this thread:
2 Guest(s)

Users browsing this thread:
2 Guest(s)