STD Maintenance General w124 climate control fan not working

w124 climate control fan not working

w124 climate control fan not working

 
  • 0 Vote(s) - 0 Average
 
MERCEDES-BENZ
K26-2

28
11-24-2013, 11:21 PM #1
I have a 87 300D and i love the car i've had it for over a year now and last December my climate control fan stopped working. No fuse blown nothing. I pulled the dash apart and found a burnt board in the climate control switches. I replaced the complete switch assembly re-installed everything and still no fan now its almost been a year and I want my heat back. I'm tired of having to speed up to get the hot air to move fast enough to get the fog off the windshield. My question is where is the fan located and is it easy to replace?
MERCEDES-BENZ
11-24-2013, 11:21 PM #1

I have a 87 300D and i love the car i've had it for over a year now and last December my climate control fan stopped working. No fuse blown nothing. I pulled the dash apart and found a burnt board in the climate control switches. I replaced the complete switch assembly re-installed everything and still no fan now its almost been a year and I want my heat back. I'm tired of having to speed up to get the hot air to move fast enough to get the fog off the windshield. My question is where is the fan located and is it easy to replace?

SurfRodder
Jackass Extraordinaire

611
11-26-2013, 09:30 AM #2
While I havent put eyes on the one in my w124 yet, it is probably in the same place as the one on my w123, which is above the passenger footwell under the dash. I've taken the dash completely out of both cars and the entire climate control out of the 123 and its not that bad, just time consuming. There is likely some good write-ups over on peach parts to get you started. You may want to do a complete rehab on the CC system if you do remove he top of the dash, but its probably a but pricey. Last time I rehabbed the vacuum system on the w123, I spent several hundred on all the vac pods, etc.

W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **

S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **

OBK# 62
SurfRodder
11-26-2013, 09:30 AM #2

While I havent put eyes on the one in my w124 yet, it is probably in the same place as the one on my w123, which is above the passenger footwell under the dash. I've taken the dash completely out of both cars and the entire climate control out of the 123 and its not that bad, just time consuming. There is likely some good write-ups over on peach parts to get you started. You may want to do a complete rehab on the CC system if you do remove he top of the dash, but its probably a but pricey. Last time I rehabbed the vacuum system on the w123, I spent several hundred on all the vac pods, etc.


W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **

S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **

OBK# 62

waz
GTA2056V

77
11-26-2013, 12:49 PM #3
It's under the cowl area. You have to remove the wiper assembly and cowl parts to get to the blower motor.

Edit: I've done two. The first took about two hours to take apart. The second, one hour to take apart and another to re-install.
This post was last modified: 11-26-2013, 12:51 PM by waz.
Attached Files
Image(s)
   

***********************************************
1993 300D 2.5L turbo. W124.128   2.5L 602.962
1991 350SD W126.134  Transplanted a 3.0L 603.961 into it.

waz
11-26-2013, 12:49 PM #3

It's under the cowl area. You have to remove the wiper assembly and cowl parts to get to the blower motor.

Edit: I've done two. The first took about two hours to take apart. The second, one hour to take apart and another to re-install.

Attached Files
Image(s)
   

***********************************************
1993 300D 2.5L turbo. W124.128   2.5L 602.962
1991 350SD W126.134  Transplanted a 3.0L 603.961 into it.

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)