STD Other Projects W123 Wagon w/ BMW M30b35 Drift Car

W123 Wagon w/ BMW M30b35 Drift Car

W123 Wagon w/ BMW M30b35 Drift Car

 
  • 0 Vote(s) - 0 Average
 
MrUkrainian
Naturally-aspirated

16
11-12-2013, 05:30 PM #1
Hey guys, I've been thinking lately and really would like to build a drift car. I have a w123 wagon that I used as a parts car for my other 123 that would make a perfect candidate. Do you guys think the bmw m30b35 would fit in the bay? What kinds of custom fabrication do you think would need to be done besides motor mounts, driveshaft, and that kind of stuff. What kind of rear end would i use? Would this swap be doable? I know it wouldn't be a diesel anymore, but I still thought I should post my idea on here. lol Thanks a lot guys.
MrUkrainian
11-12-2013, 05:30 PM #1

Hey guys, I've been thinking lately and really would like to build a drift car. I have a w123 wagon that I used as a parts car for my other 123 that would make a perfect candidate. Do you guys think the bmw m30b35 would fit in the bay? What kinds of custom fabrication do you think would need to be done besides motor mounts, driveshaft, and that kind of stuff. What kind of rear end would i use? Would this swap be doable? I know it wouldn't be a diesel anymore, but I still thought I should post my idea on here. lol Thanks a lot guys.

willbhere4u
Six in a row make her go!

2,507
11-12-2013, 05:43 PM #2
I think it would fit check the oil pan sump for clearance with the cross member would be my only concern. The stock rear diff should be fine the m30 engines really like turbos! I use to have a 1984 745i turbo 5spd technically an m106 but basically the same engine
This post was last modified: 11-12-2013, 05:45 PM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
11-12-2013, 05:43 PM #2

I think it would fit check the oil pan sump for clearance with the cross member would be my only concern. The stock rear diff should be fine the m30 engines really like turbos! I use to have a 1984 745i turbo 5spd technically an m106 but basically the same engine


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

MrUkrainian
Naturally-aspirated

16
11-13-2013, 12:24 AM #3
What would I do about the wiring harness? Would I use the m30s harness?
MrUkrainian
11-13-2013, 12:24 AM #3

What would I do about the wiring harness? Would I use the m30s harness?

muuris
OM605

318
11-13-2013, 02:00 AM #4
I had a BMW with M30, which I replaced with OM606. The measures between the engines are very close to each other, and I know a few W123/OM606 cars, so yes, it's doable with reasonable mods.

But why use M30? With n/a M30 you'd get about 250hp with reasonable costs, which I think is quite underpowered for that car. The engine is also quite heavy compared to alternatives like BMW M50 or Mercedes M104. Both have proven to be good for turbocharged ~1000hp. For about the same amount of work and dollars spent, why not to do it properly in the first place? Big Grin

Electrics need attention, no matter what engine you'll swap. There are no bolt-on solutions, but the easiest way is to use engine's own harness married to the car's harness.
This post was last modified: 11-13-2013, 02:02 AM by muuris.
muuris
11-13-2013, 02:00 AM #4

I had a BMW with M30, which I replaced with OM606. The measures between the engines are very close to each other, and I know a few W123/OM606 cars, so yes, it's doable with reasonable mods.

But why use M30? With n/a M30 you'd get about 250hp with reasonable costs, which I think is quite underpowered for that car. The engine is also quite heavy compared to alternatives like BMW M50 or Mercedes M104. Both have proven to be good for turbocharged ~1000hp. For about the same amount of work and dollars spent, why not to do it properly in the first place? Big Grin

Electrics need attention, no matter what engine you'll swap. There are no bolt-on solutions, but the easiest way is to use engine's own harness married to the car's harness.

Simpler=Better
PORTED HEAD

2,127
11-13-2013, 11:39 AM #5
If you want easy, awesome power get a SOHC or DOHC 4.6L v8 from a crown vic and turbo it. These guys hack it together and their prices are way on the low end, but if you cruise CL you can find similar stuff:

http://www.hotrod.com/techarticles/engin...ewall.html

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
11-13-2013, 11:39 AM #5

If you want easy, awesome power get a SOHC or DOHC 4.6L v8 from a crown vic and turbo it. These guys hack it together and their prices are way on the low end, but if you cruise CL you can find similar stuff:

http://www.hotrod.com/techarticles/engin...ewall.html


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

MrUkrainian
Naturally-aspirated

16
11-13-2013, 02:14 PM #6
I was thinking m30 because i could get a whole parts car for cheap. Mercedes and BMW are my favorite cars, so I think it would be cool to combine it into one. Eventually, I would turbo it, just stock internals. Everyone says these engines are boost crazy. Who knows, it could even turn into a daily driver instead of a drift car.
This post was last modified: 11-13-2013, 02:17 PM by MrUkrainian.
MrUkrainian
11-13-2013, 02:14 PM #6

I was thinking m30 because i could get a whole parts car for cheap. Mercedes and BMW are my favorite cars, so I think it would be cool to combine it into one. Eventually, I would turbo it, just stock internals. Everyone says these engines are boost crazy. Who knows, it could even turn into a daily driver instead of a drift car.

Simpler=Better
PORTED HEAD

2,127
11-13-2013, 03:06 PM #7
To each their own, I've been lusting after a boosted Coyote for a while hence my suggestion

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
11-13-2013, 03:06 PM #7

To each their own, I've been lusting after a boosted Coyote for a while hence my suggestion


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

DeliveryValve
Superturbo

1,338
11-13-2013, 04:21 PM #8
(11-13-2013, 11:39 AM)Simpler=Better If you want easy, awesome power get a SOHC or DOHC 4.6L v8 from a crown vic and turbo it. These guys hack it together and their prices are way on the low end, but if you cruise CL you can find similar stuff:

http://www.hotrod.com/techarticles/engin...ewall.html

I don't know about those Ford Modular v8's, they are just wide. Not sure it would fit in between the spring and shock towers.

On the other hand, the all aluminum Lincoln Mark VIII 32 valve DOHC (same bock as the Cobra version) are a dime a dozen and can be had for a few hundred. Add a turbo or supercharger, instant cheap HP.


.

Gota love Mercedes Diesels!



.
DeliveryValve
11-13-2013, 04:21 PM #8

(11-13-2013, 11:39 AM)Simpler=Better If you want easy, awesome power get a SOHC or DOHC 4.6L v8 from a crown vic and turbo it. These guys hack it together and their prices are way on the low end, but if you cruise CL you can find similar stuff:

http://www.hotrod.com/techarticles/engin...ewall.html

I don't know about those Ford Modular v8's, they are just wide. Not sure it would fit in between the spring and shock towers.

On the other hand, the all aluminum Lincoln Mark VIII 32 valve DOHC (same bock as the Cobra version) are a dime a dozen and can be had for a few hundred. Add a turbo or supercharger, instant cheap HP.


.


Gota love Mercedes Diesels!



.

MrUkrainian
Naturally-aspirated

16
11-13-2013, 08:04 PM #9
I'm not worried about weight. The stock OM617 weights about 600lbs when the m30 with getrag 260 weights about 550lbs.
MrUkrainian
11-13-2013, 08:04 PM #9

I'm not worried about weight. The stock OM617 weights about 600lbs when the m30 with getrag 260 weights about 550lbs.

Simpler=Better
PORTED HEAD

2,127
11-13-2013, 08:21 PM #10
(11-13-2013, 08:04 PM)MrUkrainian I'm not worried about weight. The stock OM617 weights about 600lbs when the m30 with getrag 260 weights about 550lbs.

My hernia says that the 617 weights around 650#-700#

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
11-13-2013, 08:21 PM #10

(11-13-2013, 08:04 PM)MrUkrainian I'm not worried about weight. The stock OM617 weights about 600lbs when the m30 with getrag 260 weights about 550lbs.

My hernia says that the 617 weights around 650#-700#


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)