Thread Rating:
  • 3 Vote(s) - 4.33 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Superpump builder in USA
NapaBavarian Offline
GT2256V
***


Posts: 119
Joined: Oct 2009
Location: Napa?
RE: Superpump builder in USA
Looks like I may need to set some cash aside, might go all the way to 8mm for my mechanical om606 sec
11-11-2014, 10:20 AM
Find Reply
bhowell_10 Offline
Naturally-aspirated
*


Posts: 14
Joined: Oct 2013
Location: Memphis
RE: Superpump builder in USA
I have some parts to help you guys with your builds. I have a 606 short block and injectors, I'd be willing to selll the rods and/or pistons from. Also an IP injector pump pulled from a low mileage 92 350SDL, and the turbo from the same car. I also have a turbo from a 99 E300. One of each brand. PM me if you are interested
01-05-2015, 08:30 PM
Find Reply
jenyus Offline
GT2256V
***


Posts: 158
Joined: Jan 2013
Location: Sonora, CA
RE: Superpump builder in USA
did anyone end up using the US super pump builder in a running vehicle?
(This post was last modified: 04-28-2015, 01:35 PM by jenyus.)
04-28-2015, 01:30 PM
Find Reply
raysorenson Offline
Superturbo
*****


Posts: 1,158
Joined: Sep 2011
Location: Birmingham AL
RE: Superpump builder in USA
I'm using one. It works. It's shiny too.
04-30-2015, 11:33 AM
Find Reply
jenyus Offline
GT2256V
***


Posts: 158
Joined: Jan 2013
Location: Sonora, CA
RE: Superpump builder in USA
Are you happy with it? What was your total cost and what was their turn around time?
04-30-2015, 03:43 PM
Find Reply
raysorenson Offline
Superturbo
*****


Posts: 1,158
Joined: Sep 2011
Location: Birmingham AL
RE: Superpump builder in USA
Turnaround was fuct but that was a supply issue. They had 1st gen 7.5mm elements but all parties involved wanted to wait for Goran to send 7.5mm V2 elements.

The pump is 140cc W/external ALDA limiting max fuel to 90cc for now. The motor and turbo are stock for now, I have to sort some driveline issues 1st. The increase in power is unbelievable. Top gear (1:1 5th, 2.65 R&P stock tire height) accel from 70-90 is insane considering stock turbo.

I have a slight rolling idle on startup that stabilizes in ~5-8 seconds. This may be due to my request for nearly full fuel at 6000 rpm, rather than a lack of expertise.  The guy who does the Bosch inline pumps there was also known for working MW pumps when Tomnik was selling his 6.5mm elements.

As far as price, if the tuner doesn't post it, I won't post it. And I honestly don't remember.  I got it a good while back, the V2 elements came out a while ago. The only reason I installed it before putting the big turbo on was that I needed a pick-me-up because my clutch is bumming me out.

One more thing, the pressure lever or whatever it's called has to move farther back to return to idle. This means the throttle and cruise linkage would have held the throttle open if not adjusted to compensate. They would have held it open enough to damage the motor if it couldn't be turned off quickly enough. I think a lot of pumps are like that but nobody mentions it.
04-30-2015, 08:50 PM
Find Reply
Kenny1813 Offline
Naturally-aspirated
*


Posts: 22
Joined: Mar 2015
Location: Canada
RE: Superpump builder in USA
I'm soon gonna send my IP from an OM602 in this US shop. Big Grin Göran advised me to put 7,5mm elements. Whatever is the cost, I will save my money! Tongue I also wanted to subscribe to this thread Wink
- 1992 W201 black/grey soon with Turbo OM602        -
- 1983 Porsche 944 n/a                                            -
- 2001 Toyota Echo, my daily and tough 350 000km    -
05-12-2015, 01:59 PM
Find Reply
raysorenson Offline
Superturbo
*****


Posts: 1,158
Joined: Sep 2011
Location: Birmingham AL
RE: Superpump builder in USA
Update: now that the vane air flow sensor in the bottom of my airbox is gone, the rolling idle is gone. What I get for sticking a 90cc pump on a stock motor.
07-04-2015, 09:23 AM
Find Reply
Hario' Offline
C300TD Wagon (W202)
*****


Posts: 896
Joined: Nov 2011
Location: SW London
RE: Superpump builder in USA
FYI

I'm shipping my exhaust manifold adapter to 50harleyrider on here, (UK to USA), and I'm using these people who quoted me £30GBP which I think is very cheap considering all the complaints I've heard about shipping.

It was a 4kg 200x200x200 parcel.

Possibly useful for those in USA who want dieselmeken IP's.

http://www.transglobalexpress.co.uk

Beers.



Installed:

OM606/722.6, big IC, W220 brakes.
Planned:
DIY manifold, compound, 722.6 controller, built IP.
[i]Less rust.. 
[/i]
11-11-2015, 07:12 AM
Find Reply
Vict0r Offline
Naturally-aspirated
*


Posts: 3
Joined: Feb 2019
Location: Bay Area, Ca.
RE: Superpump builder in USA
Anyone have any experience with Benzforce?

http://www.benzforce.com
02-24-2019, 03:19 PM
Find Reply
atypicalguy Offline
Holset
****


Posts: 514
Joined: Oct 2013
Location: LA
RE: Superpump builder in USA
Nice guy but you can buy all the parts direct. If you are looking for a package it might be an easy way to go. Particularly if he starts offering a bolt on intercooling solution for his hx30/pump 617 idea. Seems honest but not a car builder.
03-02-2019, 01:49 PM
Find Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)