STD Tuning Engine 1/4 mile times?

1/4 mile times?

1/4 mile times?

 
  • 0 Vote(s) - 0 Average
 
Duncansport
Holset

526
05-07-2013, 08:10 PM #1
I haven't really seen much data on what people with STD's are running for times out there. Gotta think a low 13 is possible.
I went 12.1 with my old conquest tsi with 275whp. Gotta think a well tuned 603/606 could do better. Any thoughts?
Duncansport
05-07-2013, 08:10 PM #1

I haven't really seen much data on what people with STD's are running for times out there. Gotta think a low 13 is possible.
I went 12.1 with my old conquest tsi with 275whp. Gotta think a well tuned 603/606 could do better. Any thoughts?

sassparilla_kid
diesel > all other fuels

1,618
05-07-2013, 10:27 PM #2
I don't even think my 0-60 time is 13 seconds, so 1/4 would have to be more than that as traveling a constant 60mph would be 1/4 mile every 15 seconds

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
05-07-2013, 10:27 PM #2

I don't even think my 0-60 time is 13 seconds, so 1/4 would have to be more than that as traveling a constant 60mph would be 1/4 mile every 15 seconds


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

raysorenson
Superturbo

1,162
05-08-2013, 08:09 AM #3
Normally I can give a pretty close guess on 1/4 mile times or at least trap speeds given vehicle weight, RWHP and trans setup. Unfortunately when people say their MB diesel has XX hp, they usually don't say if it CHP, RWHP or what type of dyno was used.
raysorenson
05-08-2013, 08:09 AM #3

Normally I can give a pretty close guess on 1/4 mile times or at least trap speeds given vehicle weight, RWHP and trans setup. Unfortunately when people say their MB diesel has XX hp, they usually don't say if it CHP, RWHP or what type of dyno was used.

Duncansport
Holset

526
05-08-2013, 09:28 AM #4
Part of the reason im sure is due to the fact that most people who make these engine turn to drifting rather then running the 1320..

Guess we'll see what the little 602 will do in the next few months.
Duncansport
05-08-2013, 09:28 AM #4

Part of the reason im sure is due to the fact that most people who make these engine turn to drifting rather then running the 1320..

Guess we'll see what the little 602 will do in the next few months.

willbhere4u
Six in a row make her go!

2,507
05-08-2013, 09:42 AM #5
There is a Datsun 240z with an om606 that runs in the 12.3 1/4

http://www.youtube.com/watch?v=4RghY0For0Q
This post was last modified: 05-08-2013, 09:45 AM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-08-2013, 09:42 AM #5

There is a Datsun 240z with an om606 that runs in the 12.3 1/4

http://www.youtube.com/watch?v=4RghY0For0Q


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

MFSuper90
Budget Builder

1,533
05-08-2013, 02:06 PM #6
I would guess and say my om617 would do about 9.5 in the 1/4.
Minutes that is...

'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler Big Grin
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted         
MFSuper90
05-08-2013, 02:06 PM #6

I would guess and say my om617 would do about 9.5 in the 1/4.
Minutes that is...


'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler Big Grin
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted         

mantahead
Holset

600
05-08-2013, 03:00 PM #7
hi,
my c250 did a 13.7 quarter mile(hx35, dieselmeken pump)

mantahead
05-08-2013, 03:00 PM #7

hi,
my c250 did a 13.7 quarter mile(hx35, dieselmeken pump)

Duncansport
Holset

526
05-08-2013, 06:11 PM #8
Nice run, what was your trap speed? You run a 602 pump on that engine?
Duncansport
05-08-2013, 06:11 PM #8

Nice run, what was your trap speed? You run a 602 pump on that engine?

mantahead
Holset

600
05-09-2013, 04:25 AM #9
(05-08-2013, 06:11 PM)Duncansport Nice run, what was your trap speed? You run a 602 pump on that engine?
think 104mph top speed, would need to check time slips.
yep om602 Dieselmeken pump.
mantahead
05-09-2013, 04:25 AM #9

(05-08-2013, 06:11 PM)Duncansport Nice run, what was your trap speed? You run a 602 pump on that engine?
think 104mph top speed, would need to check time slips.
yep om602 Dieselmeken pump.

Duncansport
Holset

526
05-09-2013, 06:34 AM #10
(05-09-2013, 04:25 AM)mantahead
(05-08-2013, 06:11 PM)Duncansport Nice run, what was your trap speed? You run a 602 pump on that engine?
think 104mph top speed, would need to check time slips.
yep om602 Dieselmeken pump.

Very cool, 104 trap could put you in low 13's depending on your launch and 60' times.

I don't think the OM602 will breath as well as the 605 so im sure i won't see those numbers. Just gunning for 275-300 hp range which should make a fun car.
This post was last modified: 05-09-2013, 06:39 AM by Duncansport.
Duncansport
05-09-2013, 06:34 AM #10

(05-09-2013, 04:25 AM)mantahead
(05-08-2013, 06:11 PM)Duncansport Nice run, what was your trap speed? You run a 602 pump on that engine?
think 104mph top speed, would need to check time slips.
yep om602 Dieselmeken pump.

Very cool, 104 trap could put you in low 13's depending on your launch and 60' times.

I don't think the OM602 will breath as well as the 605 so im sure i won't see those numbers. Just gunning for 275-300 hp range which should make a fun car.

mantahead
Holset

600
05-09-2013, 07:34 AM #11
(05-09-2013, 06:34 AM)Duncansport
(05-09-2013, 04:25 AM)mantahead
(05-08-2013, 06:11 PM)Duncansport Nice run, what was your trap speed? You run a 602 pump on that engine?
think 104mph top speed, would need to check time slips.
yep om602 Dieselmeken pump.

Very cool, 104 trap could put you in low 13's depending on your launch and 60' times.

I don't think the OM602 will breath as well as the 605 so im sure i won't see those numbers. Just gunning for 275-300 hp range which should make a fun car.
yea, my opel manta does 13.1 with 104mph terminal speed. The manta has better traction of the line.
mantahead
05-09-2013, 07:34 AM #11

(05-09-2013, 06:34 AM)Duncansport
(05-09-2013, 04:25 AM)mantahead
(05-08-2013, 06:11 PM)Duncansport Nice run, what was your trap speed? You run a 602 pump on that engine?
think 104mph top speed, would need to check time slips.
yep om602 Dieselmeken pump.

Very cool, 104 trap could put you in low 13's depending on your launch and 60' times.

I don't think the OM602 will breath as well as the 605 so im sure i won't see those numbers. Just gunning for 275-300 hp range which should make a fun car.
yea, my opel manta does 13.1 with 104mph terminal speed. The manta has better traction of the line.

Duncansport
Holset

526
05-09-2013, 07:55 AM #12
Opel Manta's fairly interesting little car. What powers it?

P.S. what the deal with the drag strips over there? Every video i see of a track in Europe it looks like a temporary timing setup on regular roads. Is drag racing just not that popular over there?
Duncansport
05-09-2013, 07:55 AM #12

Opel Manta's fairly interesting little car. What powers it?

P.S. what the deal with the drag strips over there? Every video i see of a track in Europe it looks like a temporary timing setup on regular roads. Is drag racing just not that popular over there?

mantahead
Holset

600
05-09-2013, 09:06 AM #13
hi,
opel manta is powered by nissan sr20 motor.
click manta.
manta

the only places long enough over here are old airfield runways, and with noise complaints and one thing another drag racing is usually only on once a month, so lights are removable.
wouldn't be just as popular over here.
This post was last modified: 05-09-2013, 09:07 AM by mantahead.
mantahead
05-09-2013, 09:06 AM #13

hi,
opel manta is powered by nissan sr20 motor.
click manta.
manta

the only places long enough over here are old airfield runways, and with noise complaints and one thing another drag racing is usually only on once a month, so lights are removable.
wouldn't be just as popular over here.

Duncansport
Holset

526
05-09-2013, 09:15 AM #14
[quote='mantahead' pid='51501' dateline='1368108388']
hi,
opel manta is powered by nissan sr20 motor.
click manta.
manta

That car is great!

So not to much top fuel events in N.Ireland? Ha. Amazing to see if you ever get a chance.
Duncansport
05-09-2013, 09:15 AM #14

[quote='mantahead' pid='51501' dateline='1368108388']
hi,
opel manta is powered by nissan sr20 motor.
click manta.
manta

That car is great!

So not to much top fuel events in N.Ireland? Ha. Amazing to see if you ever get a chance.

mantahead
Holset

600
05-09-2013, 11:02 AM #15
(05-09-2013, 09:15 AM)Duncansport [quote='mantahead' pid='51501' dateline='1368108388']
hi,
opel manta is powered by nissan sr20 motor.
click manta.
manta

That car is great!

So not to much top fuel events in N.Ireland? Ha. Amazing to see if you ever get a chance.
cheers,
did you notice the santa pod raceway pics? had to go to England to get proper drag racing. lol



ever seen this merc video?

This post was last modified: 05-09-2013, 11:06 AM by mantahead.
mantahead
05-09-2013, 11:02 AM #15

(05-09-2013, 09:15 AM)Duncansport [quote='mantahead' pid='51501' dateline='1368108388']
hi,
opel manta is powered by nissan sr20 motor.
click manta.
manta

That car is great!

So not to much top fuel events in N.Ireland? Ha. Amazing to see if you ever get a chance.
cheers,
did you notice the santa pod raceway pics? had to go to England to get proper drag racing. lol



ever seen this merc video?

Duncansport
Holset

526
05-09-2013, 11:22 AM #16
Yeah ive seen the second video one but never the first one. Nice to see something in the 10's !. I wonder what trans is behind that 606, Powerglide or TH400 maybe. Or a well built .6. Crazy though.
Duncansport
05-09-2013, 11:22 AM #16

Yeah ive seen the second video one but never the first one. Nice to see something in the 10's !. I wonder what trans is behind that 606, Powerglide or TH400 maybe. Or a well built .6. Crazy though.

mantahead
Holset

600
05-09-2013, 01:12 PM #17
like the way he loads her up on the line. Is that some special torque converter brake?
mantahead
05-09-2013, 01:12 PM #17

like the way he loads her up on the line. Is that some special torque converter brake?

raysorenson
Superturbo

1,162
05-09-2013, 02:21 PM #18
It looks like 2 upshifts.
raysorenson
05-09-2013, 02:21 PM #18

It looks like 2 upshifts.

Duncansport
Holset

526
05-09-2013, 04:40 PM #19
Its gotta be a power-glide or TH400 as they both have really good transbrake set ups available. Probably a power-glide though with the two shifts..

Mantahead-IN your thread about the C250TD tuning you did, there is a picture of the exhaust you built and in the background there are two transmission with the belhousing chopped off...whats going on there? You TIG weld that exhaust?
Duncansport
05-09-2013, 04:40 PM #19

Its gotta be a power-glide or TH400 as they both have really good transbrake set ups available. Probably a power-glide though with the two shifts..

Mantahead-IN your thread about the C250TD tuning you did, there is a picture of the exhaust you built and in the background there are two transmission with the belhousing chopped off...whats going on there? You TIG weld that exhaust?

mantahead
Holset

600
05-09-2013, 05:15 PM #20
thats the bmw box i'm using for my new project with merc bellhousing.
see here

both casing and bell housing are going to milling machine. Them bmw boxes are a bugger to split.

yea exhaust was tig welded.
This post was last modified: 05-09-2013, 05:16 PM by mantahead.
mantahead
05-09-2013, 05:15 PM #20

thats the bmw box i'm using for my new project with merc bellhousing.
see here

both casing and bell housing are going to milling machine. Them bmw boxes are a bugger to split.

yea exhaust was tig welded.

Duncansport
Holset

526
05-09-2013, 06:27 PM #21
Nice work there on the BMW box. Their manual boxes are tough as nail. To bad their autos are so terrible.
Well I suspose I've hijacked my own thread enough for now..
Duncansport
05-09-2013, 06:27 PM #21

Nice work there on the BMW box. Their manual boxes are tough as nail. To bad their autos are so terrible.
Well I suspose I've hijacked my own thread enough for now..

dieselboy
Rotatin 5500 times a minute

680
05-09-2013, 07:07 PM #22
I only did the 1/8th mile 10.5@71.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
05-09-2013, 07:07 PM #22

I only did the 1/8th mile 10.5@71.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

willbhere4u
Six in a row make her go!

2,507
05-10-2013, 09:12 AM #23
my 240d turbo 4spd ran a 21 second 1/4

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-10-2013, 09:12 AM #23

my 240d turbo 4spd ran a 21 second 1/4


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)