STD Tuning Suspension W123 lowering springs

W123 lowering springs

W123 lowering springs

 
  • 0 Vote(s) - 0 Average
 
Robert_UAH
K26-2

42
03-30-2012, 04:46 PM #1
So I was under the impression that H&R made springs for the W123 but going to their website I can't find anything for a W123. So does that leaves Spax as the only the supplier of lowering springs for these cars? Does anyone have a set of the springs laying around they can measure?
Robert_UAH
03-30-2012, 04:46 PM #1

So I was under the impression that H&R made springs for the W123 but going to their website I can't find anything for a W123. So does that leaves Spax as the only the supplier of lowering springs for these cars? Does anyone have a set of the springs laying around they can measure?

w123star
Naturally-aspirated

20
03-31-2012, 08:17 AM #2
In Europe there is more suppliers, try searching german ebay www.ebay.de and search for "tieferlegungsfedern + w123"
I dont know if they ship overseas.
Regards
Jens
w123star
03-31-2012, 08:17 AM #2

In Europe there is more suppliers, try searching german ebay www.ebay.de and search for "tieferlegungsfedern + w123"
I dont know if they ship overseas.
Regards
Jens

scosol
Unregistered

 
04-01-2012, 09:01 AM #3
(03-30-2012, 04:46 PM)Robert_UAH So I was under the impression that H&R made springs for the W123 but going to their website I can't find anything for a W123. So does that leaves Spax as the only the supplier of lowering springs for these cars? Does anyone have a set of the springs laying around they can measure?

You could cut them- we did this for racing and it worked well.
scosol
04-01-2012, 09:01 AM #3

(03-30-2012, 04:46 PM)Robert_UAH So I was under the impression that H&R made springs for the W123 but going to their website I can't find anything for a W123. So does that leaves Spax as the only the supplier of lowering springs for these cars? Does anyone have a set of the springs laying around they can measure?

You could cut them- we did this for racing and it worked well.

Captain America
Boostin' & Roostin'

2,221
04-01-2012, 01:52 PM #4
I cut mine and they work great. Car handles much better also.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
04-01-2012, 01:52 PM #4

I cut mine and they work great. Car handles much better also.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

sassparilla_kid
diesel > all other fuels

1,618
04-01-2012, 01:58 PM #5
Wouldn't the springs be softer when they're cut?

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
04-01-2012, 01:58 PM #5

Wouldn't the springs be softer when they're cut?


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Kozuka
I'm_Badass

334
04-01-2012, 07:55 PM #6
No it increases the spring rate when you cut them.
Kozuka
04-01-2012, 07:55 PM #6

No it increases the spring rate when you cut them.

sassparilla_kid
diesel > all other fuels

1,618
04-01-2012, 10:07 PM #7
So they are shorter and stiffer? Welp I guess mine need a little cutting then lol

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
04-01-2012, 10:07 PM #7

So they are shorter and stiffer? Welp I guess mine need a little cutting then lol


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Robert_UAH
K26-2

42
04-02-2012, 08:16 AM #8
There are people like QA1 and Hyperco that have tons of different spring sizes and rates and I am kinda wondering if there are any of these that fit...
Robert_UAH
04-02-2012, 08:16 AM #8

There are people like QA1 and Hyperco that have tons of different spring sizes and rates and I am kinda wondering if there are any of these that fit...

capflya
Dreaming of a VNT

309
04-04-2012, 12:14 AM #9
Lopped off 1.5 coils in the front on my car and it is much stiffer now (insert thats what she said joke here).

May just be the shocks since they're compressed more than they should be at "rest" but I don't really care because it handles a lot better now haha.



'98 E300 Turbo "Juliette" - Brabus wheels and almost all the options a w210 could have
'87 300D Turbo "Roxanne" - #22 head - 400E brakes - EGR Delete - 17" Staggered AMG 5 spoke rims from CLK500 - 5 Spd manual
2007 Chevy 2500HD CCSB Duramax with about 400-500 rwhp depending on the tune I use Big Grin
1983 300D Silver Exterior/Black inside - Sold and will be missed, may we never meet in a PnP.
capflya
04-04-2012, 12:14 AM #9

Lopped off 1.5 coils in the front on my car and it is much stiffer now (insert thats what she said joke here).

May just be the shocks since they're compressed more than they should be at "rest" but I don't really care because it handles a lot better now haha.




'98 E300 Turbo "Juliette" - Brabus wheels and almost all the options a w210 could have
'87 300D Turbo "Roxanne" - #22 head - 400E brakes - EGR Delete - 17" Staggered AMG 5 spoke rims from CLK500 - 5 Spd manual
2007 Chevy 2500HD CCSB Duramax with about 400-500 rwhp depending on the tune I use Big Grin
1983 300D Silver Exterior/Black inside - Sold and will be missed, may we never meet in a PnP.

w123love
Stockish

354
04-04-2012, 02:28 PM #10
Has anybody heard of these guys?

PI Lowering Springs for W123

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
04-04-2012, 02:28 PM #10

Has anybody heard of these guys?

PI Lowering Springs for W123


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)