7,5 mm Element design for high performance engine

STD Tuning Engine 7,5 mm Element design for high performance engine

7,5 mm Element design for high performance engine

7,5 mm Element design for high performance engine

View a Printable Version

5 Vote(s) - 4.8 Average

Holset

407

06-19-2013, 10:14 AM #389

When 17 mm roller should go into the lifter, there was not space enough,
Here you can see the lifter when its done with Wire EDM

From left, 17 mm roller in stock lifter
17 mm roller in wire EDM lifter
15 mm STD roller

With the stroked camshaft I got 275cc of fuel at max racktravel
To note is that the inlet port in the element is 3 mm, Pre stroke is 1,3mm, stroke is 18 degree "long" (4,2mm lift on element) after that the inlet port opens up in the bottom and element goes further 2,5mm to stop injection
To get 275cc on only 18 degree ( 36 engine degree) is quite quick, my old notes told me that a stock 6 mm element gives 83cc on 18 degree
7,5mm 150cc.

If I got a twin inletport and maybee only 1,5 mm hole, (1,5x2) then the pumpstroke would be 1 mm moore, Theroetical that would give me 40-50 cc moore and then the 300cc barrier is broken.
NOTE This is only in theorie, but I am tempted to try it out on a set of elements.

http://www.facebook.com/dieselmeken

dieselmeken

06-19-2013, 10:14 AM #389

When 17 mm roller should go into the lifter, there was not space enough,
Here you can see the lifter when its done with Wire EDM

From left, 17 mm roller in stock lifter
17 mm roller in wire EDM lifter
15 mm STD roller

With the stroked camshaft I got 275cc of fuel at max racktravel
To note is that the inlet port in the element is 3 mm, Pre stroke is 1,3mm, stroke is 18 degree "long" (4,2mm lift on element) after that the inlet port opens up in the bottom and element goes further 2,5mm to stop injection
To get 275cc on only 18 degree ( 36 engine degree) is quite quick, my old notes told me that a stock 6 mm element gives 83cc on 18 degree
7,5mm 150cc.

If I got a twin inletport and maybee only 1,5 mm hole, (1,5x2) then the pumpstroke would be 1 mm moore, Theroetical that would give me 40-50 cc moore and then the 300cc barrier is broken.
NOTE This is only in theorie, but I am tempted to try it out on a set of elements.

http://www.facebook.com/dieselmeken

View a Printable Version

5 Vote(s) - 4.8 Average

Messages In This Thread

7,5 mm Element design for high performance engine - by dieselmeken - 02-27-2012, 02:43 PM

RE: 7,5 mm Element design for high performance engine - by Palmer - 02-27-2012, 03:45 PM

RE: 7,5 mm Element design for high performance engine - by willbhere4u - 02-27-2012, 04:37 PM

RE: 7,5 mm Element design for high performance engine - by Booster - 02-27-2012, 06:04 PM

RE: 7,5 mm Element design for high performance engine - by w123love - 02-27-2012, 08:28 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 02-27-2012, 09:10 PM

RE: 7,5 mm Element design for high performance engine - by pp d - 02-28-2012, 01:39 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 02-28-2012, 02:13 AM

RE: 7,5 mm Element design for high performance engine - by barrote - 02-28-2012, 05:38 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 02-28-2012, 05:26 PM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-29-2012, 12:13 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 02-28-2012, 11:22 PM

RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 02-28-2012, 10:31 AM

RE: 7,5 mm Element design for high performance engine - by w210tdt - 02-28-2012, 01:04 PM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-28-2012, 01:21 PM

RE: 7,5 mm Element design for high performance engine - by 2996 - 02-28-2012, 01:22 PM

RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 02-28-2012, 01:58 PM

RE: 7,5 mm Element design for high performance engine - by Captain America - 02-29-2012, 01:25 AM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 02-29-2012, 12:31 PM

RE: 7,5 mm Element design for high performance engine - by aaa - 02-29-2012, 03:47 PM

RE: 7,5 mm Element design for high performance engine - by w123love - 02-29-2012, 09:42 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 12:58 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-01-2012, 01:41 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 07:29 PM

RE: 7,5 mm Element design for high performance engine - by aaa - 03-01-2012, 07:43 PM

RE: 7,5 mm Element design for high performance engine - by w123love - 03-01-2012, 09:33 PM

RE: 7,5 mm Element design for high performance engine - by SurfRodder - 03-02-2012, 10:18 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-04-2012, 08:34 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-05-2012, 05:20 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-05-2012, 07:51 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-06-2012, 09:43 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-07-2012, 02:22 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-04-2012, 01:59 PM

RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 03-04-2012, 04:47 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-05-2012, 06:00 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 03-05-2012, 04:15 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 01:29 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-06-2012, 02:40 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 04:14 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-07-2012, 09:37 AM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 03-07-2012, 10:44 PM

RE: 7,5 mm Element design for high performance engine - by jonbobshinigin - 03-07-2012, 11:09 PM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 03-08-2012, 02:44 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 05:05 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-08-2012, 07:40 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 08:19 AM

RE: 7,5 mm Element design for high performance engine - by Savitas - 03-09-2012, 04:01 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-11-2012, 11:51 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-15-2012, 06:33 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-08-2012, 08:02 PM

RE: 7,5 mm Element design for high performance engine - by diesel2fast4u - 03-09-2012, 02:16 AM

RE: 7,5 mm Element design for high performance engine - by George3soccer - 03-09-2012, 08:54 AM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-13-2012, 06:15 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-13-2012, 07:37 AM

RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-14-2012, 12:16 PM

RE: 7,5 mm Element design for high performance engine - by W126Lover - 03-18-2012, 12:22 AM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 03-18-2012, 01:04 AM

RE: 7,5 mm Element design for high performance engine - by pp d - 03-18-2012, 10:29 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 04:09 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 04:54 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 05:40 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 05:48 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-21-2012, 07:55 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 08:45 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-21-2012, 09:14 PM

RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-21-2012, 07:40 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 09:00 AM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 03-21-2012, 04:49 PM

RE: 7,5 mm Element design for high performance engine - by ErikT - 03-21-2012, 05:04 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-21-2012, 05:31 PM

RE: 7,5 mm Element design for high performance engine - by pp d - 03-22-2012, 01:02 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-24-2012, 08:45 AM

RE: 7,5 mm Element design for high performance engine - by Booster - 03-22-2012, 11:04 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-22-2012, 01:36 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 03-23-2012, 04:09 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 07:03 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-23-2012, 02:34 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-23-2012, 02:17 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 04:07 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-23-2012, 05:57 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-24-2012, 12:21 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-24-2012, 04:43 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 03-24-2012, 02:51 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-25-2012, 03:03 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 03-26-2012, 02:32 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-26-2012, 06:04 PM

RE: 7,5 mm Element design for high performance engine - by Savitas - 03-27-2012, 02:41 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-28-2012, 06:10 AM

RE: 7,5 mm Element design for high performance engine - by Savitas - 03-28-2012, 07:47 AM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-28-2012, 11:16 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-28-2012, 12:29 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-28-2012, 02:19 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 10:02 AM

RE: 7,5 mm Element design for high performance engine - by JustPassinThru - 03-28-2012, 11:28 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 03-28-2012, 03:29 PM

RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 03-28-2012, 03:32 PM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-29-2012, 10:19 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 04:46 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-29-2012, 11:59 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-30-2012, 02:16 AM

RE: 7,5 mm Element design for high performance engine - by swecias - 04-01-2012, 03:30 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-30-2012, 04:57 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-30-2012, 05:15 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-31-2012, 01:21 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 03-31-2012, 02:40 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-31-2012, 02:11 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 03:07 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-01-2012, 09:23 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 01:43 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-02-2012, 08:50 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-02-2012, 10:56 AM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 04-02-2012, 09:33 PM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 04-02-2012, 05:47 PM

RE: 7,5 mm Element design for high performance engine - by 2996 - 04-03-2012, 12:13 PM

RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-03-2012, 12:48 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-03-2012, 09:13 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-05-2012, 01:55 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-05-2012, 07:05 PM

RE: 7,5 mm Element design for high performance engine - by Captain America - 04-09-2012, 03:29 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-09-2012, 03:36 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-11-2012, 01:00 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-11-2012, 03:25 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-17-2012, 12:12 AM

RE: 7,5 mm Element design for high performance engine - by Volker407 - 05-28-2012, 04:20 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-28-2012, 09:45 AM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 04-17-2012, 01:54 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 04-19-2012, 04:54 PM

RE: 7,5 mm Element design for high performance engine - by yatzee - 04-19-2012, 04:56 PM

RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 04-20-2012, 08:16 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 05:56 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2012, 06:29 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 06:35 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 04-27-2012, 05:38 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-01-2012, 09:51 AM

RE: 7,5 mm Element design for high performance engine - by swecias - 05-01-2012, 03:30 PM

RE: 7,5 mm Element design for high performance engine - by Diesel-Wiking - 05-01-2012, 04:08 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-02-2012, 02:21 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-04-2012, 08:05 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-04-2012, 10:19 AM

RE: 7,5 mm Element design for high performance engine - by George3soccer - 05-04-2012, 11:45 AM

RE: 7,5 mm Element design for high performance engine - by swecias - 05-04-2012, 12:59 PM

RE: 7,5 mm Element design for high performance engine - by bricktron - 05-06-2012, 01:39 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-11-2012, 11:11 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-13-2012, 09:49 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-22-2012, 04:41 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-22-2012, 06:32 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 05-22-2012, 02:36 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-23-2012, 01:23 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-30-2012, 10:41 AM

RE: 7,5 mm Element design for high performance engine - by W126Lover - 07-17-2012, 12:03 AM

RE: 7,5 mm Element design for high performance engine - by _siim_ - 07-17-2012, 08:35 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2012, 01:03 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 06:05 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-19-2012, 12:12 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 03:02 PM

RE: 7,5 mm Element design for high performance engine - by Riverstick - 07-19-2012, 12:53 PM

RE: 7,5 mm Element design for high performance engine - by Spaceraver - 07-18-2012, 01:42 PM

RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-19-2012, 07:34 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 12:27 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 09:38 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 01:44 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 02:53 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-21-2012, 12:01 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-21-2012, 03:53 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-22-2012, 02:20 AM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-02-2012, 09:27 AM

RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-20-2012, 10:36 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-06-2012, 01:04 PM

RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-06-2012, 01:52 PM

RE: 7,5 mm Element design for high performance engine - by aaa - 08-06-2012, 11:38 PM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-07-2012, 03:38 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-07-2012, 12:52 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-07-2012, 05:34 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 10:16 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 10:24 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 11:08 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 04:42 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-08-2012, 01:23 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-08-2012, 02:33 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 03:35 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-09-2012, 03:00 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-09-2012, 06:51 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-10-2012, 10:11 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 08-10-2012, 04:04 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-10-2012, 05:36 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-13-2012, 12:41 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 08-09-2012, 12:16 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-09-2012, 02:06 PM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 06:17 AM

RE: 7,5 mm Element design for high performance engine - by Mark_M - 08-12-2012, 08:36 AM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 10:47 AM

RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-13-2012, 09:09 AM

RE: 7,5 mm Element design for high performance engine - by ronnie - 08-13-2012, 11:35 AM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 02:03 PM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-13-2012, 03:57 PM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 04:00 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-14-2012, 01:28 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 08-14-2012, 12:46 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-14-2012, 05:28 AM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-15-2012, 12:40 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-14-2012, 08:46 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-15-2012, 12:09 PM

RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 08-17-2012, 09:18 AM

RE: 7,5 mm Element design for high performance engine - by RICHIS - 08-17-2012, 05:23 PM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 11:52 AM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 08:38 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-20-2012, 08:58 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-20-2012, 09:36 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-22-2012, 06:09 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-09-2012, 03:24 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 09-09-2012, 01:46 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-10-2012, 06:01 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 09-09-2012, 09:17 PM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 09-09-2012, 10:33 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 09-10-2012, 09:14 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 06:21 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 09-12-2012, 04:29 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 11:12 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-11-2012, 04:07 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 02:40 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-12-2012, 03:55 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 04:27 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-18-2012, 09:10 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 10-19-2012, 10:17 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 10-20-2012, 03:40 PM

RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-25-2012, 03:22 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-27-2012, 04:09 AM

RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-28-2012, 01:31 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:16 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:18 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:54 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:58 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 01:04 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-07-2012, 04:30 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-08-2012, 12:31 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-08-2012, 07:38 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-09-2012, 04:19 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-02-2012, 02:01 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 02:26 PM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 11-02-2012, 06:45 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-02-2012, 08:12 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-03-2012, 08:20 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-03-2012, 10:47 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-03-2012, 06:10 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-03-2012, 07:33 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-06-2012, 05:58 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-06-2012, 02:57 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 08:18 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 11:05 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-07-2012, 05:10 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-10-2012, 12:19 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-10-2012, 01:58 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-10-2012, 03:35 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-10-2012, 03:36 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-11-2012, 12:37 PM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-12-2012, 05:51 AM

RE: 7,5 mm Element design for high performance engine - by raidaru - 11-12-2012, 12:33 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-13-2012, 12:28 PM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-15-2012, 09:05 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 10:44 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 10:44 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:02 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:10 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:14 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:17 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:22 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:09 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:11 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-15-2012, 11:24 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:12 PM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 04:18 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:21 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-15-2012, 03:27 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:21 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:26 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:32 PM

RE: 7,5 mm Element design for high performance engine - by Savitas - 11-15-2012, 02:29 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 02:54 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 04:13 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:16 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-15-2012, 04:28 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:59 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 01:45 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 02:34 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 03:30 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 04:07 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:10 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 04:17 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-16-2012, 07:00 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-16-2012, 08:30 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 11:38 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 04:42 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:56 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-18-2012, 08:45 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 07:17 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-17-2012, 08:47 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 09:14 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-17-2012, 05:12 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 05:16 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-18-2012, 12:15 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-18-2012, 12:22 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 01:18 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 01:26 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 03:20 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-22-2012, 03:14 PM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 07:07 PM

RE: 7,5 mm Element design for high performance engine - by raysorenson - 11-17-2012, 08:50 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 03:36 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:10 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-24-2012, 01:24 PM

RE: 7,5 mm Element design for high performance engine - by Mark_M - 11-22-2012, 07:34 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:39 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-23-2012, 03:31 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-23-2012, 05:06 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-23-2012, 08:37 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 12:14 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-24-2012, 07:05 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-25-2012, 09:17 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 01:09 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-24-2012, 01:19 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 03:50 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 05:42 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 06:49 PM

RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-25-2012, 11:37 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-25-2012, 03:54 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 02:55 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:16 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 12:41 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:56 PM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-27-2012, 03:11 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 03:45 PM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-27-2012, 05:39 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 05:45 PM

RE: 7,5 mm Element design for high performance engine - by hooblah - 11-27-2012, 06:07 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:14 AM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-29-2012, 03:52 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 03:55 PM

RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-29-2012, 11:21 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:25 AM

RE: 7,5 mm Element design for high performance engine - by majesty78 - 11-29-2012, 01:27 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 01:42 PM

RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 11-29-2012, 04:23 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 04:32 PM

RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 12-01-2012, 03:00 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 12-02-2012, 09:05 AM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-30-2012, 03:00 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-01-2012, 09:58 AM

RE: 7,5 mm Element design for high performance engine - by maKe- - 12-02-2012, 07:21 PM

RE: 7,5 mm Element design for high performance engine - by majesty78 - 12-11-2012, 05:49 AM

RE: 7,5 mm Element design for high performance engine - by BigAssCFotPrint - 12-11-2012, 09:50 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-20-2012, 11:00 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 01-21-2013, 01:51 AM

RE: 7,5 mm Element design for high performance engine - by raysorenson - 01-21-2013, 06:34 PM

RE: 7,5 mm Element design for high performance engine - by swecias - 03-03-2013, 12:58 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-26-2013, 08:04 AM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:11 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:18 AM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:36 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:41 AM

RE: 7,5 mm Element design for high performance engine - by frodes - 04-26-2013, 04:57 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 04-27-2013, 02:43 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2013, 05:25 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-26-2013, 04:55 PM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:12 PM

RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 04-27-2013, 06:37 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-27-2013, 05:09 PM

RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-29-2013, 10:33 AM

RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-29-2013, 11:54 AM

RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-30-2013, 04:23 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-06-2013, 01:08 PM

RE: 7,5 mm Element design for high performance engine - by Stamsaas - 05-06-2013, 02:23 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 05-06-2013, 04:00 PM

RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 05-06-2013, 04:04 PM

RE: 7,5 mm Element design for high performance engine - by Njdub - 05-06-2013, 08:53 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-12-2013, 01:46 PM

RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 06-12-2013, 02:12 PM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-12-2013, 03:15 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 06-12-2013, 04:45 PM

RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-12-2013, 09:08 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 06-13-2013, 03:32 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-13-2013, 09:56 AM

RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 06-13-2013, 03:21 PM

RE: 7,5 mm Element design for high performance engine - by Bangaway - 06-13-2013, 08:12 PM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-14-2013, 10:09 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 06-14-2013, 12:03 PM

RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 07:35 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-17-2013, 09:58 AM

RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 11:56 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 10:14 AM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-19-2013, 11:18 AM

RE: 7,5 mm Element design for high performance engine - by willbhere4u - 06-19-2013, 10:32 AM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-19-2013, 11:28 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 06-19-2013, 05:35 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 11:39 PM

RE: 7,5 mm Element design for high performance engine - by majesty78 - 06-21-2013, 06:20 AM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 06-21-2013, 07:31 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-28-2013, 08:42 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 06-28-2013, 11:55 AM

RE: 7,5 mm Element design for high performance engine - by barrote - 07-01-2013, 11:58 AM

RE: 7,5 mm Element design for high performance engine - by sorin_cel - 07-07-2013, 02:51 PM

RE: 7,5 mm Element design for high performance engine - by ErikT - 07-10-2013, 03:39 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 07-10-2013, 09:47 PM

RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-17-2013, 06:56 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2013, 10:40 AM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 07-18-2013, 08:12 AM

RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-18-2013, 01:59 PM

RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-18-2013, 05:59 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-19-2013, 04:02 AM

RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 07-19-2013, 10:13 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-19-2013, 01:48 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-21-2013, 09:09 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-22-2013, 02:58 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 07-27-2013, 03:23 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-28-2013, 08:20 AM

RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-23-2013, 08:36 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 07-23-2013, 12:34 PM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 07-26-2013, 06:43 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-06-2013, 07:17 AM

RE: 7,5 mm Element design for high performance engine - by hooblah - 09-06-2013, 10:39 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-06-2013, 01:26 PM

RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 01-21-2014, 05:41 PM

RE: 7,5 mm Element design for high performance engine - by F.R.A.S - 01-23-2014, 09:33 AM

RE: 7,5 mm Element design for high performance engine - by baldur - 02-03-2014, 09:19 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 02-03-2014, 12:43 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-28-2014, 11:10 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 04-28-2014, 02:48 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-03-2014, 06:49 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-26-2014, 02:56 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 06-26-2014, 04:39 PM

RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-26-2014, 05:00 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 01:58 AM

RE: 7,5 mm Element design for high performance engine - by Gearbound - 06-26-2014, 05:08 PM

RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 03:19 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 03:42 AM

RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 04:37 AM

RE: 7,5 mm Element design for high performance engine - by Spoolin - 09-08-2016, 12:11 PM

Users browsing this thread:
5 Guest(s)

Users browsing this thread:
5 Guest(s)