7,5 mm Element design for high performance engine

STD Tuning Engine 7,5 mm Element design for high performance engine

7,5 mm Element design for high performance engine

7,5 mm Element design for high performance engine

View a Printable Version

5 Vote(s) - 4.8 Average

EDH_Performance

Holset

537

11-17-2012, 05:16 PM #298

(11-17-2012, 05:12 PM)jeemu 605 with 550hp, Mynä 8mm, 10,5inch wheels with 255 tires
My woman go daily store shoping

Manual trans?

(11-17-2012, 04:18 PM)Siekkinen
(11-15-2012, 10:44 AM)m2rkz I got pump from dieselmeken maybe in february but now I testid it. I have master power R6164. I went to dyno and got only 194kw from wheels. max boost was already at 3500grm 2,5bar. to 3500grm there is lot of black smoke and then the boost stays to 4500 and then go lower. and then there is not much black smoke. It seems like it gets too much diesel with low grm and too few diesel in high grm. With my wastegate I must get more than 3,0 bars. but there is not enough gases. It seems like settings in pump are all wrong. EGT is max 550.

Any ideas?

There is something wrong with it. I got same results from om603 with 80mm3, 1.5 bars (holset hx35) and of course a stock feedpump.

Thats a perfect example on that the stock feed pump can handle up to 80cc of fuel, even if the pump is setup for 140cc Big Grin

Big Grin

(11-17-2012, 05:12 PM)jeemu 605 with 550hp, Mynä 8mm, 10,5inch wheels with 255 tires
My woman go daily store shoping

Manual trans?

This post was last modified: 11-17-2012, 05:18 PM by EDH_Performance.

EDH_Performance

11-17-2012, 05:16 PM #298

(11-17-2012, 05:12 PM)jeemu 605 with 550hp, Mynä 8mm, 10,5inch wheels with 255 tires
My woman go daily store shoping

Manual trans?

(11-17-2012, 04:18 PM)Siekkinen
(11-15-2012, 10:44 AM)m2rkz I got pump from dieselmeken maybe in february but now I testid it. I have master power R6164. I went to dyno and got only 194kw from wheels. max boost was already at 3500grm 2,5bar. to 3500grm there is lot of black smoke and then the boost stays to 4500 and then go lower. and then there is not much black smoke. It seems like it gets too much diesel with low grm and too few diesel in high grm. With my wastegate I must get more than 3,0 bars. but there is not enough gases. It seems like settings in pump are all wrong. EGT is max 550.

Any ideas?

There is something wrong with it. I got same results from om603 with 80mm3, 1.5 bars (holset hx35) and of course a stock feedpump.

Thats a perfect example on that the stock feed pump can handle up to 80cc of fuel, even if the pump is setup for 140cc Big Grin

Big Grin

(11-17-2012, 05:12 PM)jeemu 605 with 550hp, Mynä 8mm, 10,5inch wheels with 255 tires
My woman go daily store shoping

Manual trans?

View a Printable Version

5 Vote(s) - 4.8 Average

Messages In This Thread

7,5 mm Element design for high performance engine - by dieselmeken - 02-27-2012, 02:43 PM

RE: 7,5 mm Element design for high performance engine - by Palmer - 02-27-2012, 03:45 PM

RE: 7,5 mm Element design for high performance engine - by willbhere4u - 02-27-2012, 04:37 PM

RE: 7,5 mm Element design for high performance engine - by Booster - 02-27-2012, 06:04 PM

RE: 7,5 mm Element design for high performance engine - by w123love - 02-27-2012, 08:28 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 02-27-2012, 09:10 PM

RE: 7,5 mm Element design for high performance engine - by pp d - 02-28-2012, 01:39 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 02-28-2012, 02:13 AM

RE: 7,5 mm Element design for high performance engine - by barrote - 02-28-2012, 05:38 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 02-28-2012, 05:26 PM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-29-2012, 12:13 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 02-28-2012, 11:22 PM

RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 02-28-2012, 10:31 AM

RE: 7,5 mm Element design for high performance engine - by w210tdt - 02-28-2012, 01:04 PM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-28-2012, 01:21 PM

RE: 7,5 mm Element design for high performance engine - by 2996 - 02-28-2012, 01:22 PM

RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 02-28-2012, 01:58 PM

RE: 7,5 mm Element design for high performance engine - by Captain America - 02-29-2012, 01:25 AM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 02-29-2012, 12:31 PM

RE: 7,5 mm Element design for high performance engine - by aaa - 02-29-2012, 03:47 PM

RE: 7,5 mm Element design for high performance engine - by w123love - 02-29-2012, 09:42 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 12:58 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-01-2012, 01:41 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 07:29 PM

RE: 7,5 mm Element design for high performance engine - by aaa - 03-01-2012, 07:43 PM

RE: 7,5 mm Element design for high performance engine - by w123love - 03-01-2012, 09:33 PM

RE: 7,5 mm Element design for high performance engine - by SurfRodder - 03-02-2012, 10:18 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-04-2012, 08:34 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-05-2012, 05:20 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-05-2012, 07:51 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-06-2012, 09:43 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-07-2012, 02:22 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-04-2012, 01:59 PM

RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 03-04-2012, 04:47 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-05-2012, 06:00 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 03-05-2012, 04:15 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 01:29 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-06-2012, 02:40 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 04:14 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-07-2012, 09:37 AM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 03-07-2012, 10:44 PM

RE: 7,5 mm Element design for high performance engine - by jonbobshinigin - 03-07-2012, 11:09 PM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 03-08-2012, 02:44 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 05:05 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-08-2012, 07:40 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 08:19 AM

RE: 7,5 mm Element design for high performance engine - by Savitas - 03-09-2012, 04:01 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-11-2012, 11:51 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-15-2012, 06:33 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-08-2012, 08:02 PM

RE: 7,5 mm Element design for high performance engine - by diesel2fast4u - 03-09-2012, 02:16 AM

RE: 7,5 mm Element design for high performance engine - by George3soccer - 03-09-2012, 08:54 AM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-13-2012, 06:15 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-13-2012, 07:37 AM

RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-14-2012, 12:16 PM

RE: 7,5 mm Element design for high performance engine - by W126Lover - 03-18-2012, 12:22 AM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 03-18-2012, 01:04 AM

RE: 7,5 mm Element design for high performance engine - by pp d - 03-18-2012, 10:29 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 04:09 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 04:54 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 05:40 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 05:48 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-21-2012, 07:55 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 08:45 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-21-2012, 09:14 PM

RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-21-2012, 07:40 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 09:00 AM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 03-21-2012, 04:49 PM

RE: 7,5 mm Element design for high performance engine - by ErikT - 03-21-2012, 05:04 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-21-2012, 05:31 PM

RE: 7,5 mm Element design for high performance engine - by pp d - 03-22-2012, 01:02 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 03-24-2012, 08:45 AM

RE: 7,5 mm Element design for high performance engine - by Booster - 03-22-2012, 11:04 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-22-2012, 01:36 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 03-23-2012, 04:09 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 07:03 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-23-2012, 02:34 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-23-2012, 02:17 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 04:07 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-23-2012, 05:57 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-24-2012, 12:21 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-24-2012, 04:43 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 03-24-2012, 02:51 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-25-2012, 03:03 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 03-26-2012, 02:32 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-26-2012, 06:04 PM

RE: 7,5 mm Element design for high performance engine - by Savitas - 03-27-2012, 02:41 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-28-2012, 06:10 AM

RE: 7,5 mm Element design for high performance engine - by Savitas - 03-28-2012, 07:47 AM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-28-2012, 11:16 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-28-2012, 12:29 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-28-2012, 02:19 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 10:02 AM

RE: 7,5 mm Element design for high performance engine - by JustPassinThru - 03-28-2012, 11:28 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 03-28-2012, 03:29 PM

RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 03-28-2012, 03:32 PM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-29-2012, 10:19 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 04:46 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-29-2012, 11:59 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-30-2012, 02:16 AM

RE: 7,5 mm Element design for high performance engine - by swecias - 04-01-2012, 03:30 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-30-2012, 04:57 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-30-2012, 05:15 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 03-31-2012, 01:21 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 03-31-2012, 02:40 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 03-31-2012, 02:11 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 03:07 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-01-2012, 09:23 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 01:43 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-02-2012, 08:50 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-02-2012, 10:56 AM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 04-02-2012, 09:33 PM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 04-02-2012, 05:47 PM

RE: 7,5 mm Element design for high performance engine - by 2996 - 04-03-2012, 12:13 PM

RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-03-2012, 12:48 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-03-2012, 09:13 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-05-2012, 01:55 PM

RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-05-2012, 07:05 PM

RE: 7,5 mm Element design for high performance engine - by Captain America - 04-09-2012, 03:29 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-09-2012, 03:36 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-11-2012, 01:00 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-11-2012, 03:25 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-17-2012, 12:12 AM

RE: 7,5 mm Element design for high performance engine - by Volker407 - 05-28-2012, 04:20 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-28-2012, 09:45 AM

RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 04-17-2012, 01:54 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 04-19-2012, 04:54 PM

RE: 7,5 mm Element design for high performance engine - by yatzee - 04-19-2012, 04:56 PM

RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 04-20-2012, 08:16 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 05:56 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2012, 06:29 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 06:35 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 04-27-2012, 05:38 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-01-2012, 09:51 AM

RE: 7,5 mm Element design for high performance engine - by swecias - 05-01-2012, 03:30 PM

RE: 7,5 mm Element design for high performance engine - by Diesel-Wiking - 05-01-2012, 04:08 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-02-2012, 02:21 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-04-2012, 08:05 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-04-2012, 10:19 AM

RE: 7,5 mm Element design for high performance engine - by George3soccer - 05-04-2012, 11:45 AM

RE: 7,5 mm Element design for high performance engine - by swecias - 05-04-2012, 12:59 PM

RE: 7,5 mm Element design for high performance engine - by bricktron - 05-06-2012, 01:39 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-11-2012, 11:11 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-13-2012, 09:49 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-22-2012, 04:41 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-22-2012, 06:32 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 05-22-2012, 02:36 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-23-2012, 01:23 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-30-2012, 10:41 AM

RE: 7,5 mm Element design for high performance engine - by W126Lover - 07-17-2012, 12:03 AM

RE: 7,5 mm Element design for high performance engine - by _siim_ - 07-17-2012, 08:35 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2012, 01:03 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 06:05 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-19-2012, 12:12 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 03:02 PM

RE: 7,5 mm Element design for high performance engine - by Riverstick - 07-19-2012, 12:53 PM

RE: 7,5 mm Element design for high performance engine - by Spaceraver - 07-18-2012, 01:42 PM

RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-19-2012, 07:34 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 12:27 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 09:38 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 01:44 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 02:53 PM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-21-2012, 12:01 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-21-2012, 03:53 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 07-22-2012, 02:20 AM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-02-2012, 09:27 AM

RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-20-2012, 10:36 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-06-2012, 01:04 PM

RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-06-2012, 01:52 PM

RE: 7,5 mm Element design for high performance engine - by aaa - 08-06-2012, 11:38 PM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-07-2012, 03:38 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-07-2012, 12:52 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-07-2012, 05:34 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 10:16 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 10:24 AM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 11:08 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 04:42 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-08-2012, 01:23 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-08-2012, 02:33 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 03:35 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-09-2012, 03:00 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-09-2012, 06:51 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-10-2012, 10:11 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 08-10-2012, 04:04 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-10-2012, 05:36 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-13-2012, 12:41 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 08-09-2012, 12:16 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-09-2012, 02:06 PM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 06:17 AM

RE: 7,5 mm Element design for high performance engine - by Mark_M - 08-12-2012, 08:36 AM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 10:47 AM

RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-13-2012, 09:09 AM

RE: 7,5 mm Element design for high performance engine - by ronnie - 08-13-2012, 11:35 AM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 02:03 PM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-13-2012, 03:57 PM

RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 04:00 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 08-14-2012, 01:28 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 08-14-2012, 12:46 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-14-2012, 05:28 AM

RE: 7,5 mm Element design for high performance engine - by mercemann - 08-15-2012, 12:40 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-14-2012, 08:46 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-15-2012, 12:09 PM

RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 08-17-2012, 09:18 AM

RE: 7,5 mm Element design for high performance engine - by RICHIS - 08-17-2012, 05:23 PM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 11:52 AM

RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 08:38 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-20-2012, 08:58 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 08-20-2012, 09:36 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-22-2012, 06:09 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-09-2012, 03:24 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 09-09-2012, 01:46 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-10-2012, 06:01 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 09-09-2012, 09:17 PM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 09-09-2012, 10:33 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 09-10-2012, 09:14 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 06:21 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 09-12-2012, 04:29 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 11:12 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-11-2012, 04:07 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 02:40 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-12-2012, 03:55 AM

RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 04:27 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-18-2012, 09:10 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 10-19-2012, 10:17 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 10-20-2012, 03:40 PM

RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-25-2012, 03:22 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-27-2012, 04:09 AM

RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-28-2012, 01:31 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:16 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:18 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:54 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:58 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 01:04 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-07-2012, 04:30 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-08-2012, 12:31 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-08-2012, 07:38 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-09-2012, 04:19 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-02-2012, 02:01 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 02:26 PM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 11-02-2012, 06:45 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-02-2012, 08:12 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-03-2012, 08:20 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-03-2012, 10:47 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-03-2012, 06:10 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-03-2012, 07:33 PM

RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-06-2012, 05:58 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-06-2012, 02:57 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 08:18 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 11:05 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-07-2012, 05:10 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-10-2012, 12:19 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-10-2012, 01:58 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-10-2012, 03:35 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-10-2012, 03:36 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-11-2012, 12:37 PM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-12-2012, 05:51 AM

RE: 7,5 mm Element design for high performance engine - by raidaru - 11-12-2012, 12:33 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-13-2012, 12:28 PM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-15-2012, 09:05 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 10:44 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 10:44 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:02 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:10 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:14 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:17 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:22 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:09 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:11 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-15-2012, 11:24 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:12 PM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 04:18 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:21 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-15-2012, 03:27 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:21 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:26 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:32 PM

RE: 7,5 mm Element design for high performance engine - by Savitas - 11-15-2012, 02:29 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 02:54 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 04:13 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:16 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-15-2012, 04:28 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:59 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 01:45 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 02:34 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 03:30 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 04:07 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:10 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 04:17 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-16-2012, 07:00 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-16-2012, 08:30 AM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 11:38 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 04:42 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:56 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-18-2012, 08:45 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 07:17 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-17-2012, 08:47 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 09:14 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-17-2012, 05:12 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 05:16 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-18-2012, 12:15 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-18-2012, 12:22 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 01:18 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 01:26 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 03:20 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 11-22-2012, 03:14 PM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 07:07 PM

RE: 7,5 mm Element design for high performance engine - by raysorenson - 11-17-2012, 08:50 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 03:36 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:10 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 11-24-2012, 01:24 PM

RE: 7,5 mm Element design for high performance engine - by Mark_M - 11-22-2012, 07:34 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:39 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-23-2012, 03:31 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-23-2012, 05:06 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 11-23-2012, 08:37 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 12:14 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-24-2012, 07:05 AM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-25-2012, 09:17 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 01:09 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-24-2012, 01:19 PM

RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 03:50 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 05:42 PM

RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 06:49 PM

RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-25-2012, 11:37 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-25-2012, 03:54 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 02:55 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:16 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 12:41 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:56 PM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-27-2012, 03:11 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 03:45 PM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-27-2012, 05:39 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 05:45 PM

RE: 7,5 mm Element design for high performance engine - by hooblah - 11-27-2012, 06:07 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:14 AM

RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-29-2012, 03:52 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 03:55 PM

RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-29-2012, 11:21 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:25 AM

RE: 7,5 mm Element design for high performance engine - by majesty78 - 11-29-2012, 01:27 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 01:42 PM

RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 11-29-2012, 04:23 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 04:32 PM

RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 12-01-2012, 03:00 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 12-02-2012, 09:05 AM

RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-30-2012, 03:00 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-01-2012, 09:58 AM

RE: 7,5 mm Element design for high performance engine - by maKe- - 12-02-2012, 07:21 PM

RE: 7,5 mm Element design for high performance engine - by majesty78 - 12-11-2012, 05:49 AM

RE: 7,5 mm Element design for high performance engine - by BigAssCFotPrint - 12-11-2012, 09:50 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-20-2012, 11:00 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 01-21-2013, 01:51 AM

RE: 7,5 mm Element design for high performance engine - by raysorenson - 01-21-2013, 06:34 PM

RE: 7,5 mm Element design for high performance engine - by swecias - 03-03-2013, 12:58 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-26-2013, 08:04 AM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:11 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:18 AM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:36 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:41 AM

RE: 7,5 mm Element design for high performance engine - by frodes - 04-26-2013, 04:57 PM

RE: 7,5 mm Element design for high performance engine - by erling66 - 04-27-2013, 02:43 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2013, 05:25 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-26-2013, 04:55 PM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:12 PM

RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 04-27-2013, 06:37 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 04-27-2013, 05:09 PM

RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-29-2013, 10:33 AM

RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-29-2013, 11:54 AM

RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-30-2013, 04:23 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-06-2013, 01:08 PM

RE: 7,5 mm Element design for high performance engine - by Stamsaas - 05-06-2013, 02:23 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 05-06-2013, 04:00 PM

RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 05-06-2013, 04:04 PM

RE: 7,5 mm Element design for high performance engine - by Njdub - 05-06-2013, 08:53 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-12-2013, 01:46 PM

RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 06-12-2013, 02:12 PM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-12-2013, 03:15 PM

RE: 7,5 mm Element design for high performance engine - by mantahead - 06-12-2013, 04:45 PM

RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-12-2013, 09:08 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 06-13-2013, 03:32 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-13-2013, 09:56 AM

RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 06-13-2013, 03:21 PM

RE: 7,5 mm Element design for high performance engine - by Bangaway - 06-13-2013, 08:12 PM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-14-2013, 10:09 AM

RE: 7,5 mm Element design for high performance engine - by winmutt - 06-14-2013, 12:03 PM

RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 07:35 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-17-2013, 09:58 AM

RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 11:56 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 10:14 AM

RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-19-2013, 11:18 AM

RE: 7,5 mm Element design for high performance engine - by willbhere4u - 06-19-2013, 10:32 AM

RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-19-2013, 11:28 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 06-19-2013, 05:35 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 11:39 PM

RE: 7,5 mm Element design for high performance engine - by majesty78 - 06-21-2013, 06:20 AM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 06-21-2013, 07:31 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-28-2013, 08:42 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 06-28-2013, 11:55 AM

RE: 7,5 mm Element design for high performance engine - by barrote - 07-01-2013, 11:58 AM

RE: 7,5 mm Element design for high performance engine - by sorin_cel - 07-07-2013, 02:51 PM

RE: 7,5 mm Element design for high performance engine - by ErikT - 07-10-2013, 03:39 PM

RE: 7,5 mm Element design for high performance engine - by winmutt - 07-10-2013, 09:47 PM

RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-17-2013, 06:56 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2013, 10:40 AM

RE: 7,5 mm Element design for high performance engine - by yankneck696 - 07-18-2013, 08:12 AM

RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-18-2013, 01:59 PM

RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-18-2013, 05:59 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-19-2013, 04:02 AM

RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 07-19-2013, 10:13 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-19-2013, 01:48 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-21-2013, 09:09 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 07-22-2013, 02:58 AM

RE: 7,5 mm Element design for high performance engine - by jeemu - 07-27-2013, 03:23 PM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-28-2013, 08:20 AM

RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-23-2013, 08:36 AM

RE: 7,5 mm Element design for high performance engine - by mantahead - 07-23-2013, 12:34 PM

RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 07-26-2013, 06:43 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-06-2013, 07:17 AM

RE: 7,5 mm Element design for high performance engine - by hooblah - 09-06-2013, 10:39 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-06-2013, 01:26 PM

RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 01-21-2014, 05:41 PM

RE: 7,5 mm Element design for high performance engine - by F.R.A.S - 01-23-2014, 09:33 AM

RE: 7,5 mm Element design for high performance engine - by baldur - 02-03-2014, 09:19 AM

RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 02-03-2014, 12:43 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-28-2014, 11:10 AM

RE: 7,5 mm Element design for high performance engine - by Turbo - 04-28-2014, 02:48 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-03-2014, 06:49 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-26-2014, 02:56 PM

RE: 7,5 mm Element design for high performance engine - by Turbo - 06-26-2014, 04:39 PM

RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-26-2014, 05:00 PM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 01:58 AM

RE: 7,5 mm Element design for high performance engine - by Gearbound - 06-26-2014, 05:08 PM

RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 03:19 AM

RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 03:42 AM

RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 04:37 AM

RE: 7,5 mm Element design for high performance engine - by Spoolin - 09-08-2016, 12:11 PM

Users browsing this thread:
16 Guest(s)

Users browsing this thread:
16 Guest(s)