7,5 mm Element design for high performance engine
7,5 mm Element design for high performance engine
08-07-2012, 12:52 PM
#172
so what i say is that my engine is needing every drop of fuel to make that kind of power. doesnt give a hint of smoke over 2,5 bar. so i wounder if 140cc really is enough for high output above 600hp? if so am i seriousely having to small transfer pump if my 220cc IP doesn´t give more then 140cc now.
how much pressure to the IP does you GÖRAN think is good? mynä and jeemu told me 1bar atleast.
and is there any benyfits in having higher pressure like 5 bar or so? shouldn´t it giva a little faster injection due to the already high pressure of the fuel as it enters the element?
mvh Didrik
dieselmerc
08-07-2012, 12:52 PM #172I don´t know how much this aboat "the fuel amount isn´t important" that is true? to some point yes, but as i have seen on my w123 with om606 and compound turbo, i ran 8mm approx 220cc mynä with aboat 90% rack travel and it gave aboat 450 hp and did not not respond to increased boost, then i gave it full rack travel and it now gives 550hp but stops responding to moore boost than 3,2 bar, so i measured the fuel pressure now and it dropped below 0,4 bar on full throttle. i am using a holley blue carburetor pump on original fuel lines with just a high flow filter. i will change fuel lines to 10mm now to see if it holds above 1 bar outherwise i need bigger transfer pump.
so what i say is that my engine is needing every drop of fuel to make that kind of power. doesnt give a hint of smoke over 2,5 bar. so i wounder if 140cc really is enough for high output above 600hp? if so am i seriousely having to small transfer pump if my 220cc IP doesn´t give more then 140cc now.
how much pressure to the IP does you GÖRAN think is good? mynä and jeemu told me 1bar atleast.
and is there any benyfits in having higher pressure like 5 bar or so? shouldn´t it giva a little faster injection due to the already high pressure of the fuel as it enters the element?
mvh Didrik
Messages In This Thread
7,5 mm Element design for high performance engine - by dieselmeken - 02-27-2012, 02:43 PM
RE: 7,5 mm Element design for high performance engine - by Palmer - 02-27-2012, 03:45 PM
RE: 7,5 mm Element design for high performance engine - by willbhere4u - 02-27-2012, 04:37 PM
RE: 7,5 mm Element design for high performance engine - by Booster - 02-27-2012, 06:04 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 02-27-2012, 08:28 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 02-27-2012, 09:10 PM
RE: 7,5 mm Element design for high performance engine - by pp d - 02-28-2012, 01:39 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 02-28-2012, 02:13 AM
RE: 7,5 mm Element design for high performance engine - by barrote - 02-28-2012, 05:38 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 02-28-2012, 05:26 PM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-29-2012, 12:13 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 02-28-2012, 11:22 PM
RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 02-28-2012, 10:31 AM
RE: 7,5 mm Element design for high performance engine - by w210tdt - 02-28-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-28-2012, 01:21 PM
RE: 7,5 mm Element design for high performance engine - by 2996 - 02-28-2012, 01:22 PM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 02-28-2012, 01:58 PM
RE: 7,5 mm Element design for high performance engine - by Captain America - 02-29-2012, 01:25 AM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 02-29-2012, 12:31 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 02-29-2012, 03:47 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 02-29-2012, 09:42 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 12:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-01-2012, 01:41 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 07:29 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 03-01-2012, 07:43 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 03-01-2012, 09:33 PM
RE: 7,5 mm Element design for high performance engine - by SurfRodder - 03-02-2012, 10:18 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-04-2012, 08:34 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-05-2012, 05:20 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-05-2012, 07:51 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-06-2012, 09:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-07-2012, 02:22 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-04-2012, 01:59 PM
RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 03-04-2012, 04:47 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-05-2012, 06:00 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-05-2012, 04:15 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 01:29 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-06-2012, 02:40 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 04:14 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-07-2012, 09:37 AM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 03-07-2012, 10:44 PM
RE: 7,5 mm Element design for high performance engine - by jonbobshinigin - 03-07-2012, 11:09 PM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 03-08-2012, 02:44 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 05:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-08-2012, 07:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 08:19 AM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-09-2012, 04:01 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-11-2012, 11:51 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-15-2012, 06:33 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-08-2012, 08:02 PM
RE: 7,5 mm Element design for high performance engine - by diesel2fast4u - 03-09-2012, 02:16 AM
RE: 7,5 mm Element design for high performance engine - by George3soccer - 03-09-2012, 08:54 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-13-2012, 06:15 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-13-2012, 07:37 AM
RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-14-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by W126Lover - 03-18-2012, 12:22 AM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 03-18-2012, 01:04 AM
RE: 7,5 mm Element design for high performance engine - by pp d - 03-18-2012, 10:29 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 04:54 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 05:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 05:48 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-21-2012, 07:55 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-21-2012, 09:14 PM
RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-21-2012, 07:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 09:00 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 03-21-2012, 04:49 PM
RE: 7,5 mm Element design for high performance engine - by ErikT - 03-21-2012, 05:04 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-21-2012, 05:31 PM
RE: 7,5 mm Element design for high performance engine - by pp d - 03-22-2012, 01:02 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-24-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by Booster - 03-22-2012, 11:04 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-22-2012, 01:36 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-23-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 07:03 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-23-2012, 02:34 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-23-2012, 02:17 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 04:07 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-23-2012, 05:57 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-24-2012, 12:21 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-24-2012, 04:43 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-24-2012, 02:51 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-25-2012, 03:03 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-26-2012, 02:32 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-26-2012, 06:04 PM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-27-2012, 02:41 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-28-2012, 06:10 AM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-28-2012, 07:47 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-28-2012, 11:16 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-28-2012, 12:29 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-28-2012, 02:19 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 10:02 AM
RE: 7,5 mm Element design for high performance engine - by JustPassinThru - 03-28-2012, 11:28 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-28-2012, 03:29 PM
RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 03-28-2012, 03:32 PM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-29-2012, 10:19 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 04:46 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-29-2012, 11:59 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-30-2012, 02:16 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 04-01-2012, 03:30 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-30-2012, 04:57 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-30-2012, 05:15 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-31-2012, 01:21 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-31-2012, 02:40 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-31-2012, 02:11 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 03:07 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-01-2012, 09:23 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 01:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-02-2012, 08:50 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-02-2012, 10:56 AM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 04-02-2012, 09:33 PM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 04-02-2012, 05:47 PM
RE: 7,5 mm Element design for high performance engine - by 2996 - 04-03-2012, 12:13 PM
RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-03-2012, 12:48 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-03-2012, 09:13 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-05-2012, 01:55 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-05-2012, 07:05 PM
RE: 7,5 mm Element design for high performance engine - by Captain America - 04-09-2012, 03:29 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-09-2012, 03:36 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-11-2012, 01:00 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-11-2012, 03:25 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-17-2012, 12:12 AM
RE: 7,5 mm Element design for high performance engine - by Volker407 - 05-28-2012, 04:20 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-28-2012, 09:45 AM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 04-17-2012, 01:54 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 04-19-2012, 04:54 PM
RE: 7,5 mm Element design for high performance engine - by yatzee - 04-19-2012, 04:56 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 04-20-2012, 08:16 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 05:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2012, 06:29 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 06:35 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 04-27-2012, 05:38 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-01-2012, 09:51 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 05-01-2012, 03:30 PM
RE: 7,5 mm Element design for high performance engine - by Diesel-Wiking - 05-01-2012, 04:08 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-02-2012, 02:21 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-04-2012, 08:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-04-2012, 10:19 AM
RE: 7,5 mm Element design for high performance engine - by George3soccer - 05-04-2012, 11:45 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 05-04-2012, 12:59 PM
RE: 7,5 mm Element design for high performance engine - by bricktron - 05-06-2012, 01:39 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-11-2012, 11:11 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-13-2012, 09:49 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-22-2012, 04:41 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-22-2012, 06:32 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 05-22-2012, 02:36 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-23-2012, 01:23 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-30-2012, 10:41 AM
RE: 7,5 mm Element design for high performance engine - by W126Lover - 07-17-2012, 12:03 AM
RE: 7,5 mm Element design for high performance engine - by _siim_ - 07-17-2012, 08:35 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2012, 01:03 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 06:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-19-2012, 12:12 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 03:02 PM
RE: 7,5 mm Element design for high performance engine - by Riverstick - 07-19-2012, 12:53 PM
RE: 7,5 mm Element design for high performance engine - by Spaceraver - 07-18-2012, 01:42 PM
RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-19-2012, 07:34 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 12:27 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 09:38 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 01:44 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 02:53 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-21-2012, 12:01 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-21-2012, 03:53 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-22-2012, 02:20 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-02-2012, 09:27 AM
RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-20-2012, 10:36 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-06-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-06-2012, 01:52 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 08-06-2012, 11:38 PM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-07-2012, 03:38 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-07-2012, 12:52 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-07-2012, 05:34 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 10:16 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 10:24 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 11:08 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 04:42 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-08-2012, 01:23 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-08-2012, 02:33 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 03:35 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-09-2012, 03:00 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-09-2012, 06:51 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-10-2012, 10:11 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 08-10-2012, 04:04 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-10-2012, 05:36 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-13-2012, 12:41 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 08-09-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-09-2012, 02:06 PM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 06:17 AM
RE: 7,5 mm Element design for high performance engine - by Mark_M - 08-12-2012, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 10:47 AM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-13-2012, 09:09 AM
RE: 7,5 mm Element design for high performance engine - by ronnie - 08-13-2012, 11:35 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 02:03 PM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-13-2012, 03:57 PM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 04:00 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-14-2012, 01:28 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 08-14-2012, 12:46 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-14-2012, 05:28 AM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-15-2012, 12:40 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-14-2012, 08:46 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-15-2012, 12:09 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 08-17-2012, 09:18 AM
RE: 7,5 mm Element design for high performance engine - by RICHIS - 08-17-2012, 05:23 PM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 11:52 AM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 08:38 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-20-2012, 08:58 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-20-2012, 09:36 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-22-2012, 06:09 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-09-2012, 03:24 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 09-09-2012, 01:46 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-10-2012, 06:01 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 09-09-2012, 09:17 PM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 09-09-2012, 10:33 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 09-10-2012, 09:14 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 06:21 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 09-12-2012, 04:29 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 11:12 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-11-2012, 04:07 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 02:40 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-12-2012, 03:55 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 04:27 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-18-2012, 09:10 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 10-19-2012, 10:17 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 10-20-2012, 03:40 PM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-25-2012, 03:22 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-27-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-28-2012, 01:31 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:16 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:18 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:54 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-07-2012, 04:30 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-08-2012, 12:31 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-08-2012, 07:38 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-09-2012, 04:19 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-02-2012, 02:01 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 02:26 PM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 11-02-2012, 06:45 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-02-2012, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-03-2012, 08:20 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-03-2012, 10:47 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-03-2012, 06:10 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-03-2012, 07:33 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-06-2012, 05:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-06-2012, 02:57 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 08:18 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 11:05 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-07-2012, 05:10 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-10-2012, 12:19 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-10-2012, 01:58 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-10-2012, 03:35 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-10-2012, 03:36 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-11-2012, 12:37 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-12-2012, 05:51 AM
RE: 7,5 mm Element design for high performance engine - by raidaru - 11-12-2012, 12:33 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-13-2012, 12:28 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-15-2012, 09:05 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 10:44 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 10:44 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:02 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:10 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:14 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:17 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:22 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:09 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:11 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-15-2012, 11:24 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:12 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 04:18 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:21 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-15-2012, 03:27 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:21 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:26 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:32 PM
RE: 7,5 mm Element design for high performance engine - by Savitas - 11-15-2012, 02:29 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 02:54 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 04:13 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:16 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-15-2012, 04:28 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:59 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 01:45 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 02:34 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 03:30 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 04:07 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:10 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 04:17 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-16-2012, 07:00 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-16-2012, 08:30 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 11:38 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 04:42 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:56 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-18-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 07:17 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-17-2012, 08:47 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 09:14 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-17-2012, 05:12 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 05:16 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-18-2012, 12:15 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-18-2012, 12:22 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 01:18 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 01:26 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 03:20 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-22-2012, 03:14 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 07:07 PM
RE: 7,5 mm Element design for high performance engine - by raysorenson - 11-17-2012, 08:50 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 03:36 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:10 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-24-2012, 01:24 PM
RE: 7,5 mm Element design for high performance engine - by Mark_M - 11-22-2012, 07:34 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:39 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-23-2012, 03:31 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-23-2012, 05:06 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-23-2012, 08:37 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 12:14 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-24-2012, 07:05 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-25-2012, 09:17 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 01:09 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-24-2012, 01:19 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 03:50 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 05:42 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 06:49 PM
RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-25-2012, 11:37 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-25-2012, 03:54 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 02:55 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 12:41 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:56 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-27-2012, 03:11 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 03:45 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-27-2012, 05:39 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 05:45 PM
RE: 7,5 mm Element design for high performance engine - by hooblah - 11-27-2012, 06:07 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:14 AM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-29-2012, 03:52 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 03:55 PM
RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-29-2012, 11:21 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:25 AM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 11-29-2012, 01:27 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 01:42 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 11-29-2012, 04:23 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 04:32 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 12-01-2012, 03:00 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 12-02-2012, 09:05 AM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-30-2012, 03:00 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-01-2012, 09:58 AM
RE: 7,5 mm Element design for high performance engine - by maKe- - 12-02-2012, 07:21 PM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 12-11-2012, 05:49 AM
RE: 7,5 mm Element design for high performance engine - by BigAssCFotPrint - 12-11-2012, 09:50 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-20-2012, 11:00 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 01-21-2013, 01:51 AM
RE: 7,5 mm Element design for high performance engine - by raysorenson - 01-21-2013, 06:34 PM
RE: 7,5 mm Element design for high performance engine - by swecias - 03-03-2013, 12:58 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-26-2013, 08:04 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:11 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:18 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:41 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 04-26-2013, 04:57 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-27-2013, 02:43 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2013, 05:25 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-26-2013, 04:55 PM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 04-27-2013, 06:37 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-27-2013, 05:09 PM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-29-2013, 10:33 AM
RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-29-2013, 11:54 AM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-30-2013, 04:23 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-06-2013, 01:08 PM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 05-06-2013, 02:23 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 05-06-2013, 04:00 PM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 05-06-2013, 04:04 PM
RE: 7,5 mm Element design for high performance engine - by Njdub - 05-06-2013, 08:53 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-12-2013, 01:46 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 06-12-2013, 02:12 PM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-12-2013, 03:15 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-12-2013, 04:45 PM
RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-12-2013, 09:08 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 06-13-2013, 03:32 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-13-2013, 09:56 AM
RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 06-13-2013, 03:21 PM
RE: 7,5 mm Element design for high performance engine - by Bangaway - 06-13-2013, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-14-2013, 10:09 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 06-14-2013, 12:03 PM
RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 07:35 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-17-2013, 09:58 AM
RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 11:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 10:14 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-19-2013, 11:18 AM
RE: 7,5 mm Element design for high performance engine - by willbhere4u - 06-19-2013, 10:32 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-19-2013, 11:28 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-19-2013, 05:35 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 11:39 PM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 06-21-2013, 06:20 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 06-21-2013, 07:31 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-28-2013, 08:42 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-28-2013, 11:55 AM
RE: 7,5 mm Element design for high performance engine - by barrote - 07-01-2013, 11:58 AM
RE: 7,5 mm Element design for high performance engine - by sorin_cel - 07-07-2013, 02:51 PM
RE: 7,5 mm Element design for high performance engine - by ErikT - 07-10-2013, 03:39 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 07-10-2013, 09:47 PM
RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-17-2013, 06:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2013, 10:40 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 07-18-2013, 08:12 AM
RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-18-2013, 01:59 PM
RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-18-2013, 05:59 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-19-2013, 04:02 AM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 07-19-2013, 10:13 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-19-2013, 01:48 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-21-2013, 09:09 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-22-2013, 02:58 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 07-27-2013, 03:23 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-28-2013, 08:20 AM
RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-23-2013, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 07-23-2013, 12:34 PM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 07-26-2013, 06:43 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-06-2013, 07:17 AM
RE: 7,5 mm Element design for high performance engine - by hooblah - 09-06-2013, 10:39 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-06-2013, 01:26 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 01-21-2014, 05:41 PM
RE: 7,5 mm Element design for high performance engine - by F.R.A.S - 01-23-2014, 09:33 AM
RE: 7,5 mm Element design for high performance engine - by baldur - 02-03-2014, 09:19 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 02-03-2014, 12:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-28-2014, 11:10 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 04-28-2014, 02:48 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-03-2014, 06:49 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-26-2014, 02:56 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 06-26-2014, 04:39 PM
RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-26-2014, 05:00 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 01:58 AM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 06-26-2014, 05:08 PM
RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 03:19 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 03:42 AM
RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 04:37 AM
RE: 7,5 mm Element design for high performance engine - by Spoolin - 09-08-2016, 12:11 PM
Users browsing this thread:
15 Guest(s)
15 Guest(s)
Users browsing this thread:
15 Guest(s)
15 Guest(s)