7,5 mm Element design for high performance engine
7,5 mm Element design for high performance engine
07-19-2012, 12:53 PM
#156
(07-19-2012, 06:05 AM)tomnik(07-17-2012, 08:35 AM)_siim_ idle is 1000rpm and bit rough.
The pump should be timed 15 degrees After TDC
Hi,
why 1000/min idle??
Next: 15 deg A TDC is about 24 deg before TDC physically start of injection.
Why not retarded to physically 15 deg before TDC or even later?
The shorter duration will allow it and it is less stress for the engine, also way more smoother.
Tom
Yes Tom....You are correct about 15 degrees ATDC being 24 degrees BTDC when coming from the Mercedes factory. I had a case years ago where a Bremen 410D van was dropped to my workshop after spending three weeks in a Mercedes dealership where they failed to get it running. It transpired that someone had upset the 'indicator arm' in the governor and they were timing the engine at around 100 degrees BTDC. I ended up spill timing it at 24 degrees BTDC(the same as the OM61x's) and it ran perfectly. The van owner subsequently reported back a few weeks later claiming it had never performed like that from new.
" It is far easier to get forgiveness rather than permission"
Riverstick
07-19-2012, 12:53 PM #156(07-19-2012, 06:05 AM)tomnik(07-17-2012, 08:35 AM)_siim_ idle is 1000rpm and bit rough.
The pump should be timed 15 degrees After TDC
Hi,
why 1000/min idle??
Next: 15 deg A TDC is about 24 deg before TDC physically start of injection.
Why not retarded to physically 15 deg before TDC or even later?
The shorter duration will allow it and it is less stress for the engine, also way more smoother.
Tom
Yes Tom....You are correct about 15 degrees ATDC being 24 degrees BTDC when coming from the Mercedes factory. I had a case years ago where a Bremen 410D van was dropped to my workshop after spending three weeks in a Mercedes dealership where they failed to get it running. It transpired that someone had upset the 'indicator arm' in the governor and they were timing the engine at around 100 degrees BTDC. I ended up spill timing it at 24 degrees BTDC(the same as the OM61x's) and it ran perfectly. The van owner subsequently reported back a few weeks later claiming it had never performed like that from new.
" It is far easier to get forgiveness rather than permission"
Messages In This Thread
7,5 mm Element design for high performance engine - by dieselmeken - 02-27-2012, 02:43 PM
RE: 7,5 mm Element design for high performance engine - by Palmer - 02-27-2012, 03:45 PM
RE: 7,5 mm Element design for high performance engine - by willbhere4u - 02-27-2012, 04:37 PM
RE: 7,5 mm Element design for high performance engine - by Booster - 02-27-2012, 06:04 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 02-27-2012, 08:28 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 02-27-2012, 09:10 PM
RE: 7,5 mm Element design for high performance engine - by pp d - 02-28-2012, 01:39 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 02-28-2012, 02:13 AM
RE: 7,5 mm Element design for high performance engine - by barrote - 02-28-2012, 05:38 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 02-28-2012, 05:26 PM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-29-2012, 12:13 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 02-28-2012, 11:22 PM
RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 02-28-2012, 10:31 AM
RE: 7,5 mm Element design for high performance engine - by w210tdt - 02-28-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-28-2012, 01:21 PM
RE: 7,5 mm Element design for high performance engine - by 2996 - 02-28-2012, 01:22 PM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 02-28-2012, 01:58 PM
RE: 7,5 mm Element design for high performance engine - by Captain America - 02-29-2012, 01:25 AM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 02-29-2012, 12:31 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 02-29-2012, 03:47 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 02-29-2012, 09:42 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 12:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-01-2012, 01:41 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 07:29 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 03-01-2012, 07:43 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 03-01-2012, 09:33 PM
RE: 7,5 mm Element design for high performance engine - by SurfRodder - 03-02-2012, 10:18 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-04-2012, 08:34 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-05-2012, 05:20 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-05-2012, 07:51 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-06-2012, 09:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-07-2012, 02:22 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-04-2012, 01:59 PM
RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 03-04-2012, 04:47 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-05-2012, 06:00 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-05-2012, 04:15 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 01:29 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-06-2012, 02:40 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 04:14 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-07-2012, 09:37 AM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 03-07-2012, 10:44 PM
RE: 7,5 mm Element design for high performance engine - by jonbobshinigin - 03-07-2012, 11:09 PM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 03-08-2012, 02:44 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 05:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-08-2012, 07:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 08:19 AM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-09-2012, 04:01 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-11-2012, 11:51 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-15-2012, 06:33 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-08-2012, 08:02 PM
RE: 7,5 mm Element design for high performance engine - by diesel2fast4u - 03-09-2012, 02:16 AM
RE: 7,5 mm Element design for high performance engine - by George3soccer - 03-09-2012, 08:54 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-13-2012, 06:15 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-13-2012, 07:37 AM
RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-14-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by W126Lover - 03-18-2012, 12:22 AM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 03-18-2012, 01:04 AM
RE: 7,5 mm Element design for high performance engine - by pp d - 03-18-2012, 10:29 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 04:54 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 05:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 05:48 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-21-2012, 07:55 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-21-2012, 09:14 PM
RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-21-2012, 07:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 09:00 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 03-21-2012, 04:49 PM
RE: 7,5 mm Element design for high performance engine - by ErikT - 03-21-2012, 05:04 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-21-2012, 05:31 PM
RE: 7,5 mm Element design for high performance engine - by pp d - 03-22-2012, 01:02 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-24-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by Booster - 03-22-2012, 11:04 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-22-2012, 01:36 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-23-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 07:03 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-23-2012, 02:34 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-23-2012, 02:17 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 04:07 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-23-2012, 05:57 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-24-2012, 12:21 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-24-2012, 04:43 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-24-2012, 02:51 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-25-2012, 03:03 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-26-2012, 02:32 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-26-2012, 06:04 PM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-27-2012, 02:41 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-28-2012, 06:10 AM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-28-2012, 07:47 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-28-2012, 11:16 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-28-2012, 12:29 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-28-2012, 02:19 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 10:02 AM
RE: 7,5 mm Element design for high performance engine - by JustPassinThru - 03-28-2012, 11:28 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-28-2012, 03:29 PM
RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 03-28-2012, 03:32 PM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-29-2012, 10:19 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 04:46 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-29-2012, 11:59 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-30-2012, 02:16 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 04-01-2012, 03:30 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-30-2012, 04:57 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-30-2012, 05:15 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-31-2012, 01:21 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-31-2012, 02:40 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-31-2012, 02:11 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 03:07 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-01-2012, 09:23 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 01:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-02-2012, 08:50 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-02-2012, 10:56 AM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 04-02-2012, 09:33 PM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 04-02-2012, 05:47 PM
RE: 7,5 mm Element design for high performance engine - by 2996 - 04-03-2012, 12:13 PM
RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-03-2012, 12:48 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-03-2012, 09:13 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-05-2012, 01:55 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-05-2012, 07:05 PM
RE: 7,5 mm Element design for high performance engine - by Captain America - 04-09-2012, 03:29 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-09-2012, 03:36 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-11-2012, 01:00 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-11-2012, 03:25 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-17-2012, 12:12 AM
RE: 7,5 mm Element design for high performance engine - by Volker407 - 05-28-2012, 04:20 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-28-2012, 09:45 AM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 04-17-2012, 01:54 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 04-19-2012, 04:54 PM
RE: 7,5 mm Element design for high performance engine - by yatzee - 04-19-2012, 04:56 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 04-20-2012, 08:16 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 05:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2012, 06:29 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 06:35 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 04-27-2012, 05:38 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-01-2012, 09:51 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 05-01-2012, 03:30 PM
RE: 7,5 mm Element design for high performance engine - by Diesel-Wiking - 05-01-2012, 04:08 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-02-2012, 02:21 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-04-2012, 08:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-04-2012, 10:19 AM
RE: 7,5 mm Element design for high performance engine - by George3soccer - 05-04-2012, 11:45 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 05-04-2012, 12:59 PM
RE: 7,5 mm Element design for high performance engine - by bricktron - 05-06-2012, 01:39 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-11-2012, 11:11 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-13-2012, 09:49 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-22-2012, 04:41 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-22-2012, 06:32 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 05-22-2012, 02:36 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-23-2012, 01:23 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-30-2012, 10:41 AM
RE: 7,5 mm Element design for high performance engine - by W126Lover - 07-17-2012, 12:03 AM
RE: 7,5 mm Element design for high performance engine - by _siim_ - 07-17-2012, 08:35 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2012, 01:03 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 06:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-19-2012, 12:12 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 03:02 PM
RE: 7,5 mm Element design for high performance engine - by Riverstick - 07-19-2012, 12:53 PM
RE: 7,5 mm Element design for high performance engine - by Spaceraver - 07-18-2012, 01:42 PM
RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-19-2012, 07:34 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 12:27 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 09:38 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 01:44 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 02:53 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-21-2012, 12:01 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-21-2012, 03:53 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-22-2012, 02:20 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-02-2012, 09:27 AM
RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-20-2012, 10:36 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-06-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-06-2012, 01:52 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 08-06-2012, 11:38 PM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-07-2012, 03:38 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-07-2012, 12:52 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-07-2012, 05:34 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 10:16 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 10:24 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 11:08 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 04:42 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-08-2012, 01:23 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-08-2012, 02:33 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 03:35 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-09-2012, 03:00 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-09-2012, 06:51 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-10-2012, 10:11 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 08-10-2012, 04:04 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-10-2012, 05:36 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-13-2012, 12:41 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 08-09-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-09-2012, 02:06 PM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 06:17 AM
RE: 7,5 mm Element design for high performance engine - by Mark_M - 08-12-2012, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 10:47 AM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-13-2012, 09:09 AM
RE: 7,5 mm Element design for high performance engine - by ronnie - 08-13-2012, 11:35 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 02:03 PM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-13-2012, 03:57 PM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 04:00 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-14-2012, 01:28 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 08-14-2012, 12:46 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-14-2012, 05:28 AM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-15-2012, 12:40 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-14-2012, 08:46 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-15-2012, 12:09 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 08-17-2012, 09:18 AM
RE: 7,5 mm Element design for high performance engine - by RICHIS - 08-17-2012, 05:23 PM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 11:52 AM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 08:38 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-20-2012, 08:58 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-20-2012, 09:36 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-22-2012, 06:09 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-09-2012, 03:24 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 09-09-2012, 01:46 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-10-2012, 06:01 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 09-09-2012, 09:17 PM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 09-09-2012, 10:33 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 09-10-2012, 09:14 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 06:21 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 09-12-2012, 04:29 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 11:12 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-11-2012, 04:07 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 02:40 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-12-2012, 03:55 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 04:27 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-18-2012, 09:10 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 10-19-2012, 10:17 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 10-20-2012, 03:40 PM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-25-2012, 03:22 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-27-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-28-2012, 01:31 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:16 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:18 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:54 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-07-2012, 04:30 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-08-2012, 12:31 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-08-2012, 07:38 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-09-2012, 04:19 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-02-2012, 02:01 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 02:26 PM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 11-02-2012, 06:45 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-02-2012, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-03-2012, 08:20 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-03-2012, 10:47 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-03-2012, 06:10 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-03-2012, 07:33 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-06-2012, 05:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-06-2012, 02:57 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 08:18 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 11:05 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-07-2012, 05:10 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-10-2012, 12:19 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-10-2012, 01:58 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-10-2012, 03:35 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-10-2012, 03:36 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-11-2012, 12:37 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-12-2012, 05:51 AM
RE: 7,5 mm Element design for high performance engine - by raidaru - 11-12-2012, 12:33 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-13-2012, 12:28 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-15-2012, 09:05 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 10:44 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 10:44 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:02 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:10 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:14 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:17 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:22 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:09 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:11 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-15-2012, 11:24 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:12 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 04:18 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:21 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-15-2012, 03:27 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:21 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:26 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:32 PM
RE: 7,5 mm Element design for high performance engine - by Savitas - 11-15-2012, 02:29 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 02:54 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 04:13 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:16 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-15-2012, 04:28 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:59 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 01:45 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 02:34 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 03:30 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 04:07 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:10 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 04:17 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-16-2012, 07:00 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-16-2012, 08:30 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 11:38 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 04:42 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:56 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-18-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 07:17 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-17-2012, 08:47 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 09:14 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-17-2012, 05:12 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 05:16 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-18-2012, 12:15 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-18-2012, 12:22 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 01:18 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 01:26 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 03:20 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-22-2012, 03:14 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 07:07 PM
RE: 7,5 mm Element design for high performance engine - by raysorenson - 11-17-2012, 08:50 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 03:36 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:10 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-24-2012, 01:24 PM
RE: 7,5 mm Element design for high performance engine - by Mark_M - 11-22-2012, 07:34 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:39 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-23-2012, 03:31 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-23-2012, 05:06 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-23-2012, 08:37 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 12:14 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-24-2012, 07:05 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-25-2012, 09:17 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 01:09 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-24-2012, 01:19 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 03:50 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 05:42 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 06:49 PM
RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-25-2012, 11:37 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-25-2012, 03:54 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 02:55 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 12:41 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:56 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-27-2012, 03:11 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 03:45 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-27-2012, 05:39 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 05:45 PM
RE: 7,5 mm Element design for high performance engine - by hooblah - 11-27-2012, 06:07 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:14 AM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-29-2012, 03:52 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 03:55 PM
RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-29-2012, 11:21 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:25 AM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 11-29-2012, 01:27 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 01:42 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 11-29-2012, 04:23 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 04:32 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 12-01-2012, 03:00 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 12-02-2012, 09:05 AM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-30-2012, 03:00 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-01-2012, 09:58 AM
RE: 7,5 mm Element design for high performance engine - by maKe- - 12-02-2012, 07:21 PM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 12-11-2012, 05:49 AM
RE: 7,5 mm Element design for high performance engine - by BigAssCFotPrint - 12-11-2012, 09:50 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-20-2012, 11:00 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 01-21-2013, 01:51 AM
RE: 7,5 mm Element design for high performance engine - by raysorenson - 01-21-2013, 06:34 PM
RE: 7,5 mm Element design for high performance engine - by swecias - 03-03-2013, 12:58 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-26-2013, 08:04 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:11 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:18 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:41 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 04-26-2013, 04:57 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-27-2013, 02:43 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2013, 05:25 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-26-2013, 04:55 PM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 04-27-2013, 06:37 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-27-2013, 05:09 PM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-29-2013, 10:33 AM
RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-29-2013, 11:54 AM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-30-2013, 04:23 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-06-2013, 01:08 PM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 05-06-2013, 02:23 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 05-06-2013, 04:00 PM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 05-06-2013, 04:04 PM
RE: 7,5 mm Element design for high performance engine - by Njdub - 05-06-2013, 08:53 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-12-2013, 01:46 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 06-12-2013, 02:12 PM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-12-2013, 03:15 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-12-2013, 04:45 PM
RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-12-2013, 09:08 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 06-13-2013, 03:32 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-13-2013, 09:56 AM
RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 06-13-2013, 03:21 PM
RE: 7,5 mm Element design for high performance engine - by Bangaway - 06-13-2013, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-14-2013, 10:09 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 06-14-2013, 12:03 PM
RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 07:35 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-17-2013, 09:58 AM
RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 11:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 10:14 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-19-2013, 11:18 AM
RE: 7,5 mm Element design for high performance engine - by willbhere4u - 06-19-2013, 10:32 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-19-2013, 11:28 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-19-2013, 05:35 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 11:39 PM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 06-21-2013, 06:20 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 06-21-2013, 07:31 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-28-2013, 08:42 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-28-2013, 11:55 AM
RE: 7,5 mm Element design for high performance engine - by barrote - 07-01-2013, 11:58 AM
RE: 7,5 mm Element design for high performance engine - by sorin_cel - 07-07-2013, 02:51 PM
RE: 7,5 mm Element design for high performance engine - by ErikT - 07-10-2013, 03:39 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 07-10-2013, 09:47 PM
RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-17-2013, 06:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2013, 10:40 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 07-18-2013, 08:12 AM
RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-18-2013, 01:59 PM
RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-18-2013, 05:59 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-19-2013, 04:02 AM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 07-19-2013, 10:13 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-19-2013, 01:48 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-21-2013, 09:09 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-22-2013, 02:58 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 07-27-2013, 03:23 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-28-2013, 08:20 AM
RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-23-2013, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 07-23-2013, 12:34 PM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 07-26-2013, 06:43 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-06-2013, 07:17 AM
RE: 7,5 mm Element design for high performance engine - by hooblah - 09-06-2013, 10:39 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-06-2013, 01:26 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 01-21-2014, 05:41 PM
RE: 7,5 mm Element design for high performance engine - by F.R.A.S - 01-23-2014, 09:33 AM
RE: 7,5 mm Element design for high performance engine - by baldur - 02-03-2014, 09:19 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 02-03-2014, 12:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-28-2014, 11:10 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 04-28-2014, 02:48 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-03-2014, 06:49 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-26-2014, 02:56 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 06-26-2014, 04:39 PM
RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-26-2014, 05:00 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 01:58 AM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 06-26-2014, 05:08 PM
RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 03:19 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 03:42 AM
RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 04:37 AM
RE: 7,5 mm Element design for high performance engine - by Spoolin - 09-08-2016, 12:11 PM
Users browsing this thread:
10 Guest(s)
10 Guest(s)
Users browsing this thread:
10 Guest(s)
10 Guest(s)