7,5 mm Element design for high performance engine
7,5 mm Element design for high performance engine
07-19-2012, 12:12 PM
#155
(07-19-2012, 06:05 AM)tomnik(07-17-2012, 08:35 AM)_siim_ idle is 1000rpm and bit rough.
The pump should be timed 15 degrees After TDC
Hi,
why 1000/min idle??
Next: 15 deg A TDC is about 24 deg before TDC physically start of injection.
Why not retarded to physically 15 deg before TDC or even later?
The shorter duration will allow it and it is less stress for the engine, also way more smoother.
Tom
Tom, Obviosly the timing is totally wrong on this engine, that is chrystal clear. Think its your opinion also.
I think he must have at least 1000 rpm on low idle to get it running.
One other theori is that the throttle shaft not goes back to zero in the car, that is quite common as a mounting fault and comes from the adjustment of the governor, I have to back off the throttle stop some turns to get it down safe without afterrewing
My superpumps comes with a low idle at 650-700 rpm
0,5-0,75 degree offset in phasing as max.
Timing should be 15 ATDC when putting pump into engine, I set the timing wing in the governor with a 15 degree offset, and if you do your math then you see that timing is 15 BTDC when running at load.
Also I have a retard notch that gets 3-4 degrees later ignition under 9 mm of racktravel, then at low idle the engine goes at 12-13 BDTC and runs very smooth and nice.
That is if they are mounted properly.
(07-18-2012, 01:42 PM)Spaceraver Oh I would love to have some of your elements in my pump.. But for 250 HP/3 50nm would they be needed? Or would it be enough to pay you a visit sometime over winter? IF I get it running by that time.
You are welcome to visit my workshop. maybee 6 mm will get you there, but as always, shorter duration comes with bigger elements.
I have done a few 6 mm pumps to Denmark and they are running well according to the customers. If you wish I can give you some e.mailadress to Danish people with 6 mm pumps, pm or e-mail me if so / Göran
This post was last modified: 07-19-2012, 12:18 PM by dieselmeken.
dieselmeken
07-19-2012, 12:12 PM #155(07-19-2012, 06:05 AM)tomnik(07-17-2012, 08:35 AM)_siim_ idle is 1000rpm and bit rough.
The pump should be timed 15 degrees After TDC
Hi,
why 1000/min idle??
Next: 15 deg A TDC is about 24 deg before TDC physically start of injection.
Why not retarded to physically 15 deg before TDC or even later?
The shorter duration will allow it and it is less stress for the engine, also way more smoother.
Tom
Tom, Obviosly the timing is totally wrong on this engine, that is chrystal clear. Think its your opinion also.
I think he must have at least 1000 rpm on low idle to get it running.
One other theori is that the throttle shaft not goes back to zero in the car, that is quite common as a mounting fault and comes from the adjustment of the governor, I have to back off the throttle stop some turns to get it down safe without afterrewing
My superpumps comes with a low idle at 650-700 rpm
0,5-0,75 degree offset in phasing as max.
Timing should be 15 ATDC when putting pump into engine, I set the timing wing in the governor with a 15 degree offset, and if you do your math then you see that timing is 15 BTDC when running at load.
Also I have a retard notch that gets 3-4 degrees later ignition under 9 mm of racktravel, then at low idle the engine goes at 12-13 BDTC and runs very smooth and nice.
That is if they are mounted properly.
(07-18-2012, 01:42 PM)Spaceraver Oh I would love to have some of your elements in my pump.. But for 250 HP/3 50nm would they be needed? Or would it be enough to pay you a visit sometime over winter? IF I get it running by that time.
You are welcome to visit my workshop. maybee 6 mm will get you there, but as always, shorter duration comes with bigger elements.
I have done a few 6 mm pumps to Denmark and they are running well according to the customers. If you wish I can give you some e.mailadress to Danish people with 6 mm pumps, pm or e-mail me if so / Göran
Messages In This Thread
7,5 mm Element design for high performance engine - by dieselmeken - 02-27-2012, 02:43 PM
RE: 7,5 mm Element design for high performance engine - by Palmer - 02-27-2012, 03:45 PM
RE: 7,5 mm Element design for high performance engine - by willbhere4u - 02-27-2012, 04:37 PM
RE: 7,5 mm Element design for high performance engine - by Booster - 02-27-2012, 06:04 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 02-27-2012, 08:28 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 02-27-2012, 09:10 PM
RE: 7,5 mm Element design for high performance engine - by pp d - 02-28-2012, 01:39 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 02-28-2012, 02:13 AM
RE: 7,5 mm Element design for high performance engine - by barrote - 02-28-2012, 05:38 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 02-28-2012, 05:26 PM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-29-2012, 12:13 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 02-28-2012, 11:22 PM
RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 02-28-2012, 10:31 AM
RE: 7,5 mm Element design for high performance engine - by w210tdt - 02-28-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 02-28-2012, 01:21 PM
RE: 7,5 mm Element design for high performance engine - by 2996 - 02-28-2012, 01:22 PM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 02-28-2012, 01:58 PM
RE: 7,5 mm Element design for high performance engine - by Captain America - 02-29-2012, 01:25 AM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 02-29-2012, 12:31 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 02-29-2012, 03:47 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 02-29-2012, 09:42 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 12:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-01-2012, 01:41 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-01-2012, 07:29 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 03-01-2012, 07:43 PM
RE: 7,5 mm Element design for high performance engine - by w123love - 03-01-2012, 09:33 PM
RE: 7,5 mm Element design for high performance engine - by SurfRodder - 03-02-2012, 10:18 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-04-2012, 08:34 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-05-2012, 05:20 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-05-2012, 07:51 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-06-2012, 09:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-07-2012, 02:22 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-04-2012, 01:59 PM
RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 03-04-2012, 04:47 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-05-2012, 06:00 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-05-2012, 04:15 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 01:29 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-06-2012, 02:40 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-06-2012, 04:14 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-07-2012, 09:37 AM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 03-07-2012, 10:44 PM
RE: 7,5 mm Element design for high performance engine - by jonbobshinigin - 03-07-2012, 11:09 PM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 03-08-2012, 02:44 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 05:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-08-2012, 07:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-08-2012, 08:19 AM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-09-2012, 04:01 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-11-2012, 11:51 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-15-2012, 06:33 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 03-08-2012, 08:02 PM
RE: 7,5 mm Element design for high performance engine - by diesel2fast4u - 03-09-2012, 02:16 AM
RE: 7,5 mm Element design for high performance engine - by George3soccer - 03-09-2012, 08:54 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-13-2012, 06:15 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-13-2012, 07:37 AM
RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-14-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by W126Lover - 03-18-2012, 12:22 AM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 03-18-2012, 01:04 AM
RE: 7,5 mm Element design for high performance engine - by pp d - 03-18-2012, 10:29 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 04:54 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 05:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 05:48 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-21-2012, 07:55 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-21-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-21-2012, 09:14 PM
RE: 7,5 mm Element design for high performance engine - by Twinturboguy - 03-21-2012, 07:40 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 03-21-2012, 09:00 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 03-21-2012, 04:49 PM
RE: 7,5 mm Element design for high performance engine - by ErikT - 03-21-2012, 05:04 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-21-2012, 05:31 PM
RE: 7,5 mm Element design for high performance engine - by pp d - 03-22-2012, 01:02 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 03-24-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by Booster - 03-22-2012, 11:04 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-22-2012, 01:36 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-23-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 07:03 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-23-2012, 02:34 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-23-2012, 02:17 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-23-2012, 04:07 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-23-2012, 05:57 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-24-2012, 12:21 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-24-2012, 04:43 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-24-2012, 02:51 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-25-2012, 03:03 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 03-26-2012, 02:32 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-26-2012, 06:04 PM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-27-2012, 02:41 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-28-2012, 06:10 AM
RE: 7,5 mm Element design for high performance engine - by Savitas - 03-28-2012, 07:47 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-28-2012, 11:16 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-28-2012, 12:29 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-28-2012, 02:19 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 10:02 AM
RE: 7,5 mm Element design for high performance engine - by JustPassinThru - 03-28-2012, 11:28 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-28-2012, 03:29 PM
RE: 7,5 mm Element design for high performance engine - by Simpler=Better - 03-28-2012, 03:32 PM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 03-29-2012, 10:19 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-29-2012, 04:46 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-29-2012, 11:59 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 03-30-2012, 02:16 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 04-01-2012, 03:30 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 03-30-2012, 04:57 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-30-2012, 05:15 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 03-31-2012, 01:21 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 03-31-2012, 02:40 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 03-31-2012, 02:11 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 03:07 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-01-2012, 09:23 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-01-2012, 01:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 04-02-2012, 08:50 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-02-2012, 10:56 AM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 04-02-2012, 09:33 PM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 04-02-2012, 05:47 PM
RE: 7,5 mm Element design for high performance engine - by 2996 - 04-03-2012, 12:13 PM
RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-03-2012, 12:48 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-03-2012, 09:13 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-05-2012, 01:55 PM
RE: 7,5 mm Element design for high performance engine - by iheartboost - 04-05-2012, 07:05 PM
RE: 7,5 mm Element design for high performance engine - by Captain America - 04-09-2012, 03:29 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-09-2012, 03:36 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-11-2012, 01:00 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-11-2012, 03:25 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-17-2012, 12:12 AM
RE: 7,5 mm Element design for high performance engine - by Volker407 - 05-28-2012, 04:20 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-28-2012, 09:45 AM
RE: 7,5 mm Element design for high performance engine - by DeliveryValve - 04-17-2012, 01:54 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 04-19-2012, 04:54 PM
RE: 7,5 mm Element design for high performance engine - by yatzee - 04-19-2012, 04:56 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 04-20-2012, 08:16 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 05:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2012, 06:29 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-27-2012, 06:35 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 04-27-2012, 05:38 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-01-2012, 09:51 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 05-01-2012, 03:30 PM
RE: 7,5 mm Element design for high performance engine - by Diesel-Wiking - 05-01-2012, 04:08 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-02-2012, 02:21 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-04-2012, 08:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-04-2012, 10:19 AM
RE: 7,5 mm Element design for high performance engine - by George3soccer - 05-04-2012, 11:45 AM
RE: 7,5 mm Element design for high performance engine - by swecias - 05-04-2012, 12:59 PM
RE: 7,5 mm Element design for high performance engine - by bricktron - 05-06-2012, 01:39 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-11-2012, 11:11 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-13-2012, 09:49 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-22-2012, 04:41 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 05-22-2012, 06:32 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 05-22-2012, 02:36 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-23-2012, 01:23 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 05-30-2012, 10:41 AM
RE: 7,5 mm Element design for high performance engine - by W126Lover - 07-17-2012, 12:03 AM
RE: 7,5 mm Element design for high performance engine - by _siim_ - 07-17-2012, 08:35 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2012, 01:03 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 06:05 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-19-2012, 12:12 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-19-2012, 03:02 PM
RE: 7,5 mm Element design for high performance engine - by Riverstick - 07-19-2012, 12:53 PM
RE: 7,5 mm Element design for high performance engine - by Spaceraver - 07-18-2012, 01:42 PM
RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-19-2012, 07:34 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 12:27 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 09:38 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-20-2012, 01:44 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-20-2012, 02:53 PM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-21-2012, 12:01 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-21-2012, 03:53 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 07-22-2012, 02:20 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-02-2012, 09:27 AM
RE: 7,5 mm Element design for high performance engine - by Greazzer - 07-20-2012, 10:36 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-06-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-06-2012, 01:52 PM
RE: 7,5 mm Element design for high performance engine - by aaa - 08-06-2012, 11:38 PM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-07-2012, 03:38 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-07-2012, 12:52 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-07-2012, 05:34 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 10:16 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 10:24 AM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 11:08 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-08-2012, 04:42 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-08-2012, 01:23 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-08-2012, 02:33 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-08-2012, 03:35 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-09-2012, 03:00 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-09-2012, 06:51 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-10-2012, 10:11 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 08-10-2012, 04:04 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-10-2012, 05:36 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-13-2012, 12:41 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 08-09-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-09-2012, 02:06 PM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 06:17 AM
RE: 7,5 mm Element design for high performance engine - by Mark_M - 08-12-2012, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-12-2012, 10:47 AM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 08-13-2012, 09:09 AM
RE: 7,5 mm Element design for high performance engine - by ronnie - 08-13-2012, 11:35 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 02:03 PM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-13-2012, 03:57 PM
RE: 7,5 mm Element design for high performance engine - by frodes - 08-13-2012, 04:00 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 08-14-2012, 01:28 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 08-14-2012, 12:46 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 08-14-2012, 05:28 AM
RE: 7,5 mm Element design for high performance engine - by mercemann - 08-15-2012, 12:40 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-14-2012, 08:46 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 08-15-2012, 12:09 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 08-17-2012, 09:18 AM
RE: 7,5 mm Element design for high performance engine - by RICHIS - 08-17-2012, 05:23 PM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 11:52 AM
RE: 7,5 mm Element design for high performance engine - by sassparilla_kid - 08-18-2012, 08:38 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-20-2012, 08:58 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 08-20-2012, 09:36 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 08-22-2012, 06:09 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-09-2012, 03:24 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 09-09-2012, 01:46 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-10-2012, 06:01 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 09-09-2012, 09:17 PM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 09-09-2012, 10:33 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 09-10-2012, 09:14 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 06:21 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 09-12-2012, 04:29 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-10-2012, 11:12 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-11-2012, 04:07 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 02:40 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-12-2012, 03:55 AM
RE: 7,5 mm Element design for high performance engine - by tomnik - 09-12-2012, 04:27 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-18-2012, 09:10 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 10-19-2012, 10:17 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 10-20-2012, 03:40 PM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-25-2012, 03:22 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 10-27-2012, 04:09 AM
RE: 7,5 mm Element design for high performance engine - by huseyin55amg - 10-28-2012, 01:31 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:16 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:18 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 11:54 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-02-2012, 11:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 01:04 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-07-2012, 04:30 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-08-2012, 12:31 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-08-2012, 07:38 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-09-2012, 04:19 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-02-2012, 02:01 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-02-2012, 02:26 PM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 11-02-2012, 06:45 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-02-2012, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-03-2012, 08:20 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-03-2012, 10:47 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-03-2012, 06:10 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-03-2012, 07:33 PM
RE: 7,5 mm Element design for high performance engine - by dieselmerc - 11-06-2012, 05:58 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-06-2012, 02:57 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 08:18 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-06-2012, 11:05 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-07-2012, 05:10 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-10-2012, 12:19 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-10-2012, 01:58 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-10-2012, 03:35 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-10-2012, 03:36 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-11-2012, 12:37 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-12-2012, 05:51 AM
RE: 7,5 mm Element design for high performance engine - by raidaru - 11-12-2012, 12:33 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-13-2012, 12:28 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-15-2012, 09:05 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 10:44 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 10:44 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:02 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:10 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:14 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 11:17 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 11:22 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:09 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:11 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-15-2012, 11:24 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:12 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 04:18 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:21 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-15-2012, 03:27 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:21 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 12:26 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 12:32 PM
RE: 7,5 mm Element design for high performance engine - by Savitas - 11-15-2012, 02:29 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 02:54 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-15-2012, 04:13 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:16 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-15-2012, 04:28 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-15-2012, 04:59 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 01:45 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 02:34 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 03:30 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-16-2012, 04:07 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:10 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 04:17 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-16-2012, 07:00 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-16-2012, 08:30 AM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-16-2012, 11:38 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-16-2012, 04:42 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 11-16-2012, 04:56 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-18-2012, 08:45 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 07:17 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-17-2012, 08:47 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 09:14 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-17-2012, 05:12 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-17-2012, 05:16 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-18-2012, 12:15 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-18-2012, 12:22 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 01:18 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 01:26 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 03:20 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 11-22-2012, 03:14 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-17-2012, 07:07 PM
RE: 7,5 mm Element design for high performance engine - by raysorenson - 11-17-2012, 08:50 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-22-2012, 03:36 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:10 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 11-24-2012, 01:24 PM
RE: 7,5 mm Element design for high performance engine - by Mark_M - 11-22-2012, 07:34 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-22-2012, 07:39 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-23-2012, 03:31 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-23-2012, 05:06 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 11-23-2012, 08:37 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 12:14 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-24-2012, 07:05 AM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-25-2012, 09:17 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 01:09 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-24-2012, 01:19 PM
RE: 7,5 mm Element design for high performance engine - by jeemu - 11-24-2012, 03:50 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 05:42 PM
RE: 7,5 mm Element design for high performance engine - by m2rkz - 11-24-2012, 06:49 PM
RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-25-2012, 11:37 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-25-2012, 03:54 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 02:55 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:16 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 11-26-2012, 12:41 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-26-2012, 12:56 PM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-27-2012, 03:11 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 03:45 PM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-27-2012, 05:39 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-27-2012, 05:45 PM
RE: 7,5 mm Element design for high performance engine - by hooblah - 11-27-2012, 06:07 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:14 AM
RE: 7,5 mm Element design for high performance engine - by Siekkinen - 11-29-2012, 03:52 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 03:55 PM
RE: 7,5 mm Element design for high performance engine - by 300SD81 - 11-29-2012, 11:21 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 11:25 AM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 11-29-2012, 01:27 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 01:42 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 11-29-2012, 04:23 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 11-29-2012, 04:32 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 12-01-2012, 03:00 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 12-02-2012, 09:05 AM
RE: 7,5 mm Element design for high performance engine - by Ksteen2 - 11-30-2012, 03:00 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-01-2012, 09:58 AM
RE: 7,5 mm Element design for high performance engine - by maKe- - 12-02-2012, 07:21 PM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 12-11-2012, 05:49 AM
RE: 7,5 mm Element design for high performance engine - by BigAssCFotPrint - 12-11-2012, 09:50 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 12-20-2012, 11:00 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 01-21-2013, 01:51 AM
RE: 7,5 mm Element design for high performance engine - by raysorenson - 01-21-2013, 06:34 PM
RE: 7,5 mm Element design for high performance engine - by swecias - 03-03-2013, 12:58 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-26-2013, 08:04 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:11 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:18 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-26-2013, 08:41 AM
RE: 7,5 mm Element design for high performance engine - by frodes - 04-26-2013, 04:57 PM
RE: 7,5 mm Element design for high performance engine - by erling66 - 04-27-2013, 02:43 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-27-2013, 05:25 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 04-26-2013, 04:55 PM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 04-26-2013, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 04-27-2013, 06:37 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 04-27-2013, 05:09 PM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-29-2013, 10:33 AM
RE: 7,5 mm Element design for high performance engine - by lgreeley83 - 04-29-2013, 11:54 AM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 04-30-2013, 04:23 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-06-2013, 01:08 PM
RE: 7,5 mm Element design for high performance engine - by Stamsaas - 05-06-2013, 02:23 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 05-06-2013, 04:00 PM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 05-06-2013, 04:04 PM
RE: 7,5 mm Element design for high performance engine - by Njdub - 05-06-2013, 08:53 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-12-2013, 01:46 PM
RE: 7,5 mm Element design for high performance engine - by hansebanger77 - 06-12-2013, 02:12 PM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-12-2013, 03:15 PM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-12-2013, 04:45 PM
RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-12-2013, 09:08 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 06-13-2013, 03:32 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-13-2013, 09:56 AM
RE: 7,5 mm Element design for high performance engine - by squirrelmaster - 06-13-2013, 03:21 PM
RE: 7,5 mm Element design for high performance engine - by Bangaway - 06-13-2013, 08:12 PM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-14-2013, 10:09 AM
RE: 7,5 mm Element design for high performance engine - by winmutt - 06-14-2013, 12:03 PM
RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 07:35 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-17-2013, 09:58 AM
RE: 7,5 mm Element design for high performance engine - by maKe- - 06-17-2013, 11:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 10:14 AM
RE: 7,5 mm Element design for high performance engine - by Duncansport - 06-19-2013, 11:18 AM
RE: 7,5 mm Element design for high performance engine - by willbhere4u - 06-19-2013, 10:32 AM
RE: 7,5 mm Element design for high performance engine - by Alastair E - 06-19-2013, 11:28 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-19-2013, 05:35 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-19-2013, 11:39 PM
RE: 7,5 mm Element design for high performance engine - by majesty78 - 06-21-2013, 06:20 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 06-21-2013, 07:31 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-28-2013, 08:42 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 06-28-2013, 11:55 AM
RE: 7,5 mm Element design for high performance engine - by barrote - 07-01-2013, 11:58 AM
RE: 7,5 mm Element design for high performance engine - by sorin_cel - 07-07-2013, 02:51 PM
RE: 7,5 mm Element design for high performance engine - by ErikT - 07-10-2013, 03:39 PM
RE: 7,5 mm Element design for high performance engine - by winmutt - 07-10-2013, 09:47 PM
RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-17-2013, 06:56 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-17-2013, 10:40 AM
RE: 7,5 mm Element design for high performance engine - by yankneck696 - 07-18-2013, 08:12 AM
RE: 7,5 mm Element design for high performance engine - by Domino81 - 07-18-2013, 01:59 PM
RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-18-2013, 05:59 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-19-2013, 04:02 AM
RE: 7,5 mm Element design for high performance engine - by HaavardPYA - 07-19-2013, 10:13 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-19-2013, 01:48 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 07-21-2013, 09:09 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 07-22-2013, 02:58 AM
RE: 7,5 mm Element design for high performance engine - by jeemu - 07-27-2013, 03:23 PM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 07-28-2013, 08:20 AM
RE: 7,5 mm Element design for high performance engine - by maxypriest - 07-23-2013, 08:36 AM
RE: 7,5 mm Element design for high performance engine - by mantahead - 07-23-2013, 12:34 PM
RE: 7,5 mm Element design for high performance engine - by HoleshotHolset - 07-26-2013, 06:43 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 09-06-2013, 07:17 AM
RE: 7,5 mm Element design for high performance engine - by hooblah - 09-06-2013, 10:39 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 09-06-2013, 01:26 PM
RE: 7,5 mm Element design for high performance engine - by 300SD_KY - 01-21-2014, 05:41 PM
RE: 7,5 mm Element design for high performance engine - by F.R.A.S - 01-23-2014, 09:33 AM
RE: 7,5 mm Element design for high performance engine - by baldur - 02-03-2014, 09:19 AM
RE: 7,5 mm Element design for high performance engine - by EDH_Performance - 02-03-2014, 12:43 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 04-28-2014, 11:10 AM
RE: 7,5 mm Element design for high performance engine - by Turbo - 04-28-2014, 02:48 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 05-03-2014, 06:49 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-26-2014, 02:56 PM
RE: 7,5 mm Element design for high performance engine - by Turbo - 06-26-2014, 04:39 PM
RE: 7,5 mm Element design for high performance engine - by MFSuper90 - 06-26-2014, 05:00 PM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 01:58 AM
RE: 7,5 mm Element design for high performance engine - by Gearbound - 06-26-2014, 05:08 PM
RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 03:19 AM
RE: 7,5 mm Element design for high performance engine - by dieselmeken - 06-27-2014, 03:42 AM
RE: 7,5 mm Element design for high performance engine - by DiseaselWeasel - 06-27-2014, 04:37 AM
RE: 7,5 mm Element design for high performance engine - by Spoolin - 09-08-2016, 12:11 PM
Users browsing this thread:
17 Guest(s)
17 Guest(s)
Users browsing this thread:
17 Guest(s)
17 Guest(s)