STD Tuning Engine 7,5 mm Element design for high performance engine

7,5 mm Element design for high performance engine

7,5 mm Element design for high performance engine

 
  • 5 Vote(s) - 4.8 Average
 
Pages (9): 1 2 3 4 5 9 Next  
dieselmeken
Holset

407
02-27-2012, 02:43 PM #1
As some of you here on the STD forum knows, I have been struggling with making my own pumpelement for the M-seriepump. I want to reveal some facts what I have done the last year.

Previously I have done pumps with the "old" 7 mm Ford Transit element, Also with the 6 mm original OM606 element. My opinion was that the 7 mm didnt work out well at all, High knock at low idle, high fuelconsumption max 120cc was some of the disadvantages with those.

6 mm was running perfect, good balance nice idle and so on.

After those pumps my customers wanted moore fuel, Myna was running 170cc with there own 7 mm element, However I could not buy those, Myna dont sell element only, they just put them in there own pumps. The explanation I got was that
-It is some difference in quality.

At this moment I have around 10-15 pumps waiting for nice, big element whit a lot of fuel.
Something had to bee doneDodgy

I started do design the first serie of 7,5 mm element, It took around 3 months for the factory to make them for me.
At this moment I have payed around 8000 euro.
After 4 months the goods arriwed, I was glad for about 4,5 minute, then everything went to ****.
Barrel was too big, didnt even fit in the pumphousing, plunger was 0,15mm to long, The plunger could not go to top in the pump, it was stuck.
This however I could fix, my friend, who has a mechanical workshop helped me.
Barrels was grinded down to right dimensions so that they fitted in the housing, plunger was modified so that I could mount them in the pump.

First pump was 2,5 degrees wrong in phasing, That was no big deal, but it gave me a lot of extra work, changing rollers in the tappet lifter so the balance was OK.

Next thing was fuelquantity, I was expecting a bit over 170cc but no.
140-150 cc was max at 21mm of rack BUT, It had capacity for OVER 200ccBig GrinBig Grin
The "only" thing was that the helixangel on the element was to flat, I would need around 25-26 mm of rack to get 100% out of the element.

80 elements where adjusted, 10pc of 140cc pumps was built with good result. I bougt a 250TD with OM605 just for testing the pumpelements properly.
Rest of the elements where shipped back to the factory for modification.

Serie 2 was up on drawingtable, wise from the first serie I know now how it should bee designed, Serie 2 has som benefits that serie 1 dont have.
Here is a small teaserRolleyes
   
   
   

50 days from today and serie 2 will arriwe for testing. After that gentlemen, I think that I can offer you some nice pumps.
140cc & a bit moore.





dieselmeken
02-27-2012, 02:43 PM #1

As some of you here on the STD forum knows, I have been struggling with making my own pumpelement for the M-seriepump. I want to reveal some facts what I have done the last year.

Previously I have done pumps with the "old" 7 mm Ford Transit element, Also with the 6 mm original OM606 element. My opinion was that the 7 mm didnt work out well at all, High knock at low idle, high fuelconsumption max 120cc was some of the disadvantages with those.

6 mm was running perfect, good balance nice idle and so on.

After those pumps my customers wanted moore fuel, Myna was running 170cc with there own 7 mm element, However I could not buy those, Myna dont sell element only, they just put them in there own pumps. The explanation I got was that
-It is some difference in quality.

At this moment I have around 10-15 pumps waiting for nice, big element whit a lot of fuel.
Something had to bee doneDodgy

I started do design the first serie of 7,5 mm element, It took around 3 months for the factory to make them for me.
At this moment I have payed around 8000 euro.
After 4 months the goods arriwed, I was glad for about 4,5 minute, then everything went to ****.
Barrel was too big, didnt even fit in the pumphousing, plunger was 0,15mm to long, The plunger could not go to top in the pump, it was stuck.
This however I could fix, my friend, who has a mechanical workshop helped me.
Barrels was grinded down to right dimensions so that they fitted in the housing, plunger was modified so that I could mount them in the pump.

First pump was 2,5 degrees wrong in phasing, That was no big deal, but it gave me a lot of extra work, changing rollers in the tappet lifter so the balance was OK.

Next thing was fuelquantity, I was expecting a bit over 170cc but no.
140-150 cc was max at 21mm of rack BUT, It had capacity for OVER 200ccBig GrinBig Grin
The "only" thing was that the helixangel on the element was to flat, I would need around 25-26 mm of rack to get 100% out of the element.

80 elements where adjusted, 10pc of 140cc pumps was built with good result. I bougt a 250TD with OM605 just for testing the pumpelements properly.
Rest of the elements where shipped back to the factory for modification.

Serie 2 was up on drawingtable, wise from the first serie I know now how it should bee designed, Serie 2 has som benefits that serie 1 dont have.
Here is a small teaserRolleyes
   
   
   

50 days from today and serie 2 will arriwe for testing. After that gentlemen, I think that I can offer you some nice pumps.
140cc & a bit moore.





Palmer
GTA2056V

93
02-27-2012, 03:45 PM #2
(02-27-2012, 02:43 PM)dieselmeken As some of you here on the STD forum knows, I have been struggling with making my own pumpelement for the M-seriepump. I want to reveal some facts what I have done the last year.

Previously I have done pumps with the "old" 7 mm Ford Transit element, Also with the 6 mm original OM606 element. My opinion was that the 7 mm didnt work out well at all, High knock at low idle, high fuelconsumption max 120cc was some of the disadvantages with those.

6 mm was running perfect, good balance nice idle and so on.

After those pumps my customers wanted moore fuel, Myna was running 170cc with there own 7 mm element, However I could not buy those, Myna dont sell element only, they just put them in there own pumps. The explanation I got was that
-It is some difference in quality.

At this moment I have around 10-15 pumps waiting for nice, big element whit a lot of fuel.
Something had to bee doneDodgy

I started do design the first serie of 7,5 mm element, It took around 3 months for the factory to make them for me.
At this moment I have payed around 8000 euro.
After 4 months the goods arriwed, I was glad for about 4,5 minute, then everything went to ****.
Barrel was too big, didnt even fit in the pumphousing, plunger was 0,15mm to long, The plunger could not go to top in the pump, it was stuck.
This however I could fix, my friend, who has a mechanical workshop helped me.
Barrels was grinded down to right dimensions so that they fitted in the housing, plunger was modified so that I could mount them in the pump.

First pump was 2,5 degrees wrong in phasing, That was no big deal, but it gave me a lot of extra work, changing rollers in the tappet lifter so the balance was OK.

Next thing was fuelquantity, I was expecting a bit over 170cc but no.
140-150 cc was max at 21mm of rack BUT, It had capacity for OVER 200ccBig GrinBig Grin
The "only" thing was that the helixangel on the element was to flat, I would need around 25-26 mm of rack to get 100% out of the element.

80 elements where adjusted, 10pc of 140cc pumps was built with good result. I bougt a 250TD with OM605 just for testing the pumpelements properly.
Rest of the elements where shipped back to the factory for modification.

Serie 2 was up on drawingtable, wise from the first serie I know now how it should bee designed, Serie 2 has som benefits that serie 1 dont have.
Here is a small teaserRolleyes




50 days from today and serie 2 will arriwe for testing. After that gentlemen, I think that I can offer you some nice pumps.
140cc & a bit moore.

Nice one mate.

Ill be looking for a power pump soon for my C250 OM605 Wink
Palmer
02-27-2012, 03:45 PM #2

(02-27-2012, 02:43 PM)dieselmeken As some of you here on the STD forum knows, I have been struggling with making my own pumpelement for the M-seriepump. I want to reveal some facts what I have done the last year.

Previously I have done pumps with the "old" 7 mm Ford Transit element, Also with the 6 mm original OM606 element. My opinion was that the 7 mm didnt work out well at all, High knock at low idle, high fuelconsumption max 120cc was some of the disadvantages with those.

6 mm was running perfect, good balance nice idle and so on.

After those pumps my customers wanted moore fuel, Myna was running 170cc with there own 7 mm element, However I could not buy those, Myna dont sell element only, they just put them in there own pumps. The explanation I got was that
-It is some difference in quality.

At this moment I have around 10-15 pumps waiting for nice, big element whit a lot of fuel.
Something had to bee doneDodgy

I started do design the first serie of 7,5 mm element, It took around 3 months for the factory to make them for me.
At this moment I have payed around 8000 euro.
After 4 months the goods arriwed, I was glad for about 4,5 minute, then everything went to ****.
Barrel was too big, didnt even fit in the pumphousing, plunger was 0,15mm to long, The plunger could not go to top in the pump, it was stuck.
This however I could fix, my friend, who has a mechanical workshop helped me.
Barrels was grinded down to right dimensions so that they fitted in the housing, plunger was modified so that I could mount them in the pump.

First pump was 2,5 degrees wrong in phasing, That was no big deal, but it gave me a lot of extra work, changing rollers in the tappet lifter so the balance was OK.

Next thing was fuelquantity, I was expecting a bit over 170cc but no.
140-150 cc was max at 21mm of rack BUT, It had capacity for OVER 200ccBig GrinBig Grin
The "only" thing was that the helixangel on the element was to flat, I would need around 25-26 mm of rack to get 100% out of the element.

80 elements where adjusted, 10pc of 140cc pumps was built with good result. I bougt a 250TD with OM605 just for testing the pumpelements properly.
Rest of the elements where shipped back to the factory for modification.

Serie 2 was up on drawingtable, wise from the first serie I know now how it should bee designed, Serie 2 has som benefits that serie 1 dont have.
Here is a small teaserRolleyes




50 days from today and serie 2 will arriwe for testing. After that gentlemen, I think that I can offer you some nice pumps.
140cc & a bit moore.

Nice one mate.

Ill be looking for a power pump soon for my C250 OM605 Wink

willbhere4u
Six in a row make her go!

2,507
02-27-2012, 04:37 PM #3
Thanks for all of your hard work! And for posting on this forum. I'm excited to see how this works out I'll have to start saving up for a custom pump!Big Grin
This post was last modified: 02-27-2012, 04:37 PM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
02-27-2012, 04:37 PM #3

Thanks for all of your hard work! And for posting on this forum. I'm excited to see how this works out I'll have to start saving up for a custom pump!Big Grin


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Booster
GT2559V

240
02-27-2012, 06:04 PM #4
I can't wait for these to be offered properly!
Booster
02-27-2012, 06:04 PM #4

I can't wait for these to be offered properly!

w123love
Stockish

354
02-27-2012, 08:28 PM #5
Schttttoked!

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
02-27-2012, 08:28 PM #5

Schttttoked!


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

winmutt
bitbanger

3,468
02-27-2012, 09:10 PM #6
What did the factory say?

-Rolf

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
02-27-2012, 09:10 PM #6

What did the factory say?

-Rolf


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

pp d
K26-2

42
02-28-2012, 01:39 AM #7
Well... I made a pump with 150 cc delivery for Tom, sent it about a week ago.
No need such thing as 20-21 mm track travel Dodgy
pp d
02-28-2012, 01:39 AM #7

Well... I made a pump with 150 cc delivery for Tom, sent it about a week ago.
No need such thing as 20-21 mm track travel Dodgy

dieselmeken
Holset

407
02-28-2012, 02:13 AM #8
(02-28-2012, 01:39 AM)pp d Well... I made a pump with 150 cc delivery for Tom, sent it about a week ago.
No need such thing as 20-21 mm track travel Dodgy

Ofcourse you did. You get a element that works in the first place, You can buy element from Tom, How hard can it bee then? You dont design, you just build the pump.
Toms element is nice if you dont need moore fuel that 140-.150cc, My customers building high performance engine, just as the topic says, and then Toms element is not enough

Im trying to explain how difficult this is, I dont need any devaluation.
I think this is going to workout perfect, just you wait and see.
Some people has not been so helpful to me, that is one of the reasons I had to do something.
dieselmeken
02-28-2012, 02:13 AM #8

(02-28-2012, 01:39 AM)pp d Well... I made a pump with 150 cc delivery for Tom, sent it about a week ago.
No need such thing as 20-21 mm track travel Dodgy

Ofcourse you did. You get a element that works in the first place, You can buy element from Tom, How hard can it bee then? You dont design, you just build the pump.
Toms element is nice if you dont need moore fuel that 140-.150cc, My customers building high performance engine, just as the topic says, and then Toms element is not enough

Im trying to explain how difficult this is, I dont need any devaluation.
I think this is going to workout perfect, just you wait and see.
Some people has not been so helpful to me, that is one of the reasons I had to do something.

barrote
Superturbo

1,627
02-28-2012, 05:38 AM #9
(02-28-2012, 02:13 AM)dieselmeken
(02-28-2012, 01:39 AM)pp d Well... I made a pump with 150 cc delivery for Tom, sent it about a week ago.
No need such thing as 20-21 mm track travel Dodgy

Ofcourse you did. You get a element that works in the first place, You can buy element from Tom, How hard can it bee then? You dont design, you just build the pump.
Toms element is nice if you dont need moore fuel that 140-.150cc, My customers building high performance engine, just as the topic says, and then Toms element is not enough

Im trying to explain how difficult this is, I dont need any devaluation.
I think this is going to workout perfect, just you wait and see.
Some people has not been so helpful to me, that is one of the reasons I had to do something.

hope u succeed, from the deepest hope it work out,
do u have any idea what are u going to do after , will u rebuild the pumps or just available the elements?
go on that the right way to fight.

FD,
Powered by tractor fuel
barrote
02-28-2012, 05:38 AM #9

(02-28-2012, 02:13 AM)dieselmeken
(02-28-2012, 01:39 AM)pp d Well... I made a pump with 150 cc delivery for Tom, sent it about a week ago.
No need such thing as 20-21 mm track travel Dodgy

Ofcourse you did. You get a element that works in the first place, You can buy element from Tom, How hard can it bee then? You dont design, you just build the pump.
Toms element is nice if you dont need moore fuel that 140-.150cc, My customers building high performance engine, just as the topic says, and then Toms element is not enough

Im trying to explain how difficult this is, I dont need any devaluation.
I think this is going to workout perfect, just you wait and see.
Some people has not been so helpful to me, that is one of the reasons I had to do something.

hope u succeed, from the deepest hope it work out,
do u have any idea what are u going to do after , will u rebuild the pumps or just available the elements?
go on that the right way to fight.


FD,
Powered by tractor fuel

Simpler=Better
PORTED HEAD

2,127
02-28-2012, 10:31 AM #10
I like the sounds of 200cc Big Grin
This post was last modified: 02-28-2012, 10:31 AM by Simpler=Better.

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
02-28-2012, 10:31 AM #10

I like the sounds of 200cc Big Grin


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

w210tdt
K26-2

31
02-28-2012, 01:04 PM #11
Keep up the good work gøran! Smile
w210tdt
02-28-2012, 01:04 PM #11

Keep up the good work gøran! Smile

DeliveryValve
Superturbo

1,338
02-28-2012, 01:21 PM #12
Göran, Thanks many times over for posting your thoughts, expertise and videos on injection pump building. Folks like myself love to see these journeys in type of build in action and explained.

I hope all the success in this one and perhaps maybe later, you can design and manufacture an affordable higher output MW element. Cool



.

Gota love Mercedes Diesels!



.
DeliveryValve
02-28-2012, 01:21 PM #12

Göran, Thanks many times over for posting your thoughts, expertise and videos on injection pump building. Folks like myself love to see these journeys in type of build in action and explained.

I hope all the success in this one and perhaps maybe later, you can design and manufacture an affordable higher output MW element. Cool



.


Gota love Mercedes Diesels!



.

2996
K26-2

45
02-28-2012, 01:22 PM #13
Interesting and very effective looking helix design. I am glad someone is making an element that gives more fuel than ~150ccm, as why go through all the trouble and expense with changing the elements only to find you need more fuel. <150ccm elements have there place as well.

Thanks for posting this, and keep up with the great, and sometimes discouraging work!
2996
02-28-2012, 01:22 PM #13

Interesting and very effective looking helix design. I am glad someone is making an element that gives more fuel than ~150ccm, as why go through all the trouble and expense with changing the elements only to find you need more fuel. <150ccm elements have there place as well.

Thanks for posting this, and keep up with the great, and sometimes discouraging work!

huseyin55amg
Naturally-aspirated

20
02-28-2012, 01:58 PM #14
great news goran ! do you keep the standard turbo ? is it able to cope with the extra fuel delivery..?

keep us posted goran......

rgds hus
huseyin55amg
02-28-2012, 01:58 PM #14

great news goran ! do you keep the standard turbo ? is it able to cope with the extra fuel delivery..?

keep us posted goran......

rgds hus

tomnik
Holset

587
02-28-2012, 05:26 PM #15
(02-28-2012, 02:13 AM)dieselmeken Toms element is nice if you dont need moore fuel that 140-.150cc, My customers building high performance engine, just as the topic says, and then Toms element is not enough

Hi,

not correct in the case of my SuperFloyd pump.
As I always pray the thing is not to move end of delivery too late.
I am retarding down BOD to about 18deg for smooth engine run and low emission and still end delivery within the Bosch recommendation therefore the limit of quantity.
Now my new prototype delivers 150 ccm but still respecting the safe range of the Bosch book and standard rack travel and standard governor operation.
My new elements could easily exceed 200 ccm but I don't care as only very few people can burn this amount of fuel without black clouds of smoke.
Anyway good job, I know very well what it takes to calculate, design and manufacture elements in excellent qualityCool

Tom
tomnik
02-28-2012, 05:26 PM #15

(02-28-2012, 02:13 AM)dieselmeken Toms element is nice if you dont need moore fuel that 140-.150cc, My customers building high performance engine, just as the topic says, and then Toms element is not enough

Hi,

not correct in the case of my SuperFloyd pump.
As I always pray the thing is not to move end of delivery too late.
I am retarding down BOD to about 18deg for smooth engine run and low emission and still end delivery within the Bosch recommendation therefore the limit of quantity.
Now my new prototype delivers 150 ccm but still respecting the safe range of the Bosch book and standard rack travel and standard governor operation.
My new elements could easily exceed 200 ccm but I don't care as only very few people can burn this amount of fuel without black clouds of smoke.
Anyway good job, I know very well what it takes to calculate, design and manufacture elements in excellent qualityCool

Tom

winmutt
bitbanger

3,468
02-28-2012, 11:22 PM #16
(02-28-2012, 02:13 AM)dieselmeken Im trying to explain how difficult this is, I dont need any devaluation.

I support this statement.

It's great that ppd came up with a pump using Tom's elements. I look forward to what dm offers as well. Tom went through several iterations as well IIRC.

More to the point, you guys are offering competition to Myna. I think everyone here appreciates all the hard work everyone has put in.

-Rolf

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
02-28-2012, 11:22 PM #16

(02-28-2012, 02:13 AM)dieselmeken Im trying to explain how difficult this is, I dont need any devaluation.

I support this statement.

It's great that ppd came up with a pump using Tom's elements. I look forward to what dm offers as well. Tom went through several iterations as well IIRC.

More to the point, you guys are offering competition to Myna. I think everyone here appreciates all the hard work everyone has put in.

-Rolf


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
02-29-2012, 01:25 AM #17
You are Awesome Gøran! Heart


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
02-29-2012, 01:25 AM #17

You are Awesome Gøran! Heart



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

DeliveryValve
Superturbo

1,338
02-29-2012, 12:13 PM #18
(02-28-2012, 05:26 PM)tomnik ...
Now my new prototype delivers 150 ccm but still respecting the safe range of the Bosch book and standard rack travel and standard governor operation....
Tom


If I was in the market for M-pump elements, this would be what would want regarding the setup because of the lack of experience in IP building up here in the States. Make it easier for the tech.

BTW -Not to highjack your thread Göran, But Tom, how much are your elements? And are you going to do another run of the MW?


.

Gota love Mercedes Diesels!



.
DeliveryValve
02-29-2012, 12:13 PM #18

(02-28-2012, 05:26 PM)tomnik ...
Now my new prototype delivers 150 ccm but still respecting the safe range of the Bosch book and standard rack travel and standard governor operation....
Tom


If I was in the market for M-pump elements, this would be what would want regarding the setup because of the lack of experience in IP building up here in the States. Make it easier for the tech.

BTW -Not to highjack your thread Göran, But Tom, how much are your elements? And are you going to do another run of the MW?


.


Gota love Mercedes Diesels!



.

sassparilla_kid
diesel &gt; all other fuels

1,618
02-29-2012, 12:31 PM #19
If I had an M-pump I would buy these elements in a second!!

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
02-29-2012, 12:31 PM #19

If I had an M-pump I would buy these elements in a second!!


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

aaa
GT2256V

913
02-29-2012, 03:47 PM #20
Would be nice if the american 617 people didn't even have to mail stuff in to be modded, since 617 m-pumps are in europe already.
aaa
02-29-2012, 03:47 PM #20

Would be nice if the american 617 people didn't even have to mail stuff in to be modded, since 617 m-pumps are in europe already.

w123love
Stockish

354
02-29-2012, 09:42 PM #21
I have a M-pump that needs to be modified. Who do I need to talk to?

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
02-29-2012, 09:42 PM #21

I have a M-pump that needs to be modified. Who do I need to talk to?


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

tomnik
Holset

587
03-01-2012, 12:58 AM #22
(02-29-2012, 09:42 PM)w123love I have a M-pump that needs to be modified. Who do I need to talk to?

...to DeliveryValve ...

Tom
tomnik
03-01-2012, 12:58 AM #22

(02-29-2012, 09:42 PM)w123love I have a M-pump that needs to be modified. Who do I need to talk to?

...to DeliveryValve ...

Tom

dieselmeken
Holset

407
03-01-2012, 01:41 AM #23


(03-01-2012, 12:58 AM)tomnik
(02-29-2012, 09:42 PM)w123love I have a M-pump that needs to be modified. Who do I need to talk to?

...to DeliveryValve ...

Tom

Or you can talk to me if you wish.
dieselmeken
03-01-2012, 01:41 AM #23



(03-01-2012, 12:58 AM)tomnik
(02-29-2012, 09:42 PM)w123love I have a M-pump that needs to be modified. Who do I need to talk to?

...to DeliveryValve ...

Tom

Or you can talk to me if you wish.

tomnik
Holset

587
03-01-2012, 07:29 PM #24
(03-01-2012, 01:41 AM)dieselmeken Or you can talk to me if you wish.

Hi Göran,

the interest was in having a US guy do the pump...

Tom
tomnik
03-01-2012, 07:29 PM #24

(03-01-2012, 01:41 AM)dieselmeken Or you can talk to me if you wish.

Hi Göran,

the interest was in having a US guy do the pump...

Tom

aaa
GT2256V

913
03-01-2012, 07:43 PM #25
(03-01-2012, 07:29 PM)tomnik
(03-01-2012, 01:41 AM)dieselmeken Or you can talk to me if you wish.

Hi Göran,

the interest was in having a US guy do the pump...

Tom

That wasn't mentioned here. Although it would indeed be preferable. I wonder about the timeliness though, of both alternatives.
aaa
03-01-2012, 07:43 PM #25

(03-01-2012, 07:29 PM)tomnik
(03-01-2012, 01:41 AM)dieselmeken Or you can talk to me if you wish.

Hi Göran,

the interest was in having a US guy do the pump...

Tom

That wasn't mentioned here. Although it would indeed be preferable. I wonder about the timeliness though, of both alternatives.

w123love
Stockish

354
03-01-2012, 09:33 PM #26
I don’t want a US guy touching my pump. I don’t want to be a lab rat. I want a pro. So offshore it will go.

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
03-01-2012, 09:33 PM #26

I don’t want a US guy touching my pump. I don’t want to be a lab rat. I want a pro. So offshore it will go.


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

SurfRodder
Jackass Extraordinaire

611
03-02-2012, 10:18 AM #27
(03-01-2012, 09:33 PM)w123love I don’t want a US guy touching my pump. I don’t want to be a lab rat. I want a pro. So offshore it will go.

The guy that did my pump in Fresno is a self proclaimed "Mercedes Geek" and works at an IP shop with likely the same/equivalent test gear to do the actual tuning...not sure how much more "pro" you need...mine has Tom's elements BTW... hope to install it soon.

I also have an M-pump lying around that I may mess with at a later date, but I'm sure it'll go to the same guy for tuning.

W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **

S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **

OBK# 62
SurfRodder
03-02-2012, 10:18 AM #27

(03-01-2012, 09:33 PM)w123love I don’t want a US guy touching my pump. I don’t want to be a lab rat. I want a pro. So offshore it will go.

The guy that did my pump in Fresno is a self proclaimed "Mercedes Geek" and works at an IP shop with likely the same/equivalent test gear to do the actual tuning...not sure how much more "pro" you need...mine has Tom's elements BTW... hope to install it soon.

I also have an M-pump lying around that I may mess with at a later date, but I'm sure it'll go to the same guy for tuning.


W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **

S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **

OBK# 62

EDH_Performance
Holset

537
03-04-2012, 08:34 AM #28
Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink
This post was last modified: 03-04-2012, 08:41 AM by EDH_Performance.
EDH_Performance
03-04-2012, 08:34 AM #28

Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink

dieselmeken
Holset

407
03-04-2012, 01:59 PM #29
Yes, I know that my serie 1 element works out well, it just needs some more love and care when putting them into the pump.
Nothing for do it yorself.
Serie 1 will never bee sold as part only, I only put them in by myself.
Serie 2 however will be on the market, But only after testing them out.


I am glad that EDH_performance i happy with his dm superpump.
This post was last modified: 03-04-2012, 02:00 PM by dieselmeken.
dieselmeken
03-04-2012, 01:59 PM #29

Yes, I know that my serie 1 element works out well, it just needs some more love and care when putting them into the pump.
Nothing for do it yorself.
Serie 1 will never bee sold as part only, I only put them in by myself.
Serie 2 however will be on the market, But only after testing them out.


I am glad that EDH_performance i happy with his dm superpump.

squirrelmaster
smokey

49
03-04-2012, 04:47 PM #30
(03-04-2012, 01:59 PM)dieselmeken Yes, I know that my serie 1 element works out well, it just needs some more love and care when putting them into the pump.
Nothing for do it yorself.
Serie 1 will never bee sold as part only, I only put them in by myself.
Serie 2 however will be on the market, But only after testing them out.


I am glad that EDH_performance i happy with his dm superpump.

price per series 2 element ? and any idea of when these may be ready
squirrelmaster
03-04-2012, 04:47 PM #30

(03-04-2012, 01:59 PM)dieselmeken Yes, I know that my serie 1 element works out well, it just needs some more love and care when putting them into the pump.
Nothing for do it yorself.
Serie 1 will never bee sold as part only, I only put them in by myself.
Serie 2 however will be on the market, But only after testing them out.


I am glad that EDH_performance i happy with his dm superpump.

price per series 2 element ? and any idea of when these may be ready

dieselmeken
Holset

407
03-05-2012, 06:00 AM #31
(03-04-2012, 04:47 PM)squirrelmaster
(03-04-2012, 01:59 PM)dieselmeken Yes, I know that my serie 1 element works out well, it just needs some more love and care when putting them into the pump.
Nothing for do it yorself.
Serie 1 will never bee sold as part only, I only put them in by myself.
Serie 2 however will be on the market, But only after testing them out.


I am glad that EDH_performance i happy with his dm superpump.

price per series 2 element ? and any idea of when these may be ready

As I wrote at first, 50 days approx. Price is not set yet. I must test them out first.

dieselmeken
03-05-2012, 06:00 AM #31

(03-04-2012, 04:47 PM)squirrelmaster
(03-04-2012, 01:59 PM)dieselmeken Yes, I know that my serie 1 element works out well, it just needs some more love and care when putting them into the pump.
Nothing for do it yorself.
Serie 1 will never bee sold as part only, I only put them in by myself.
Serie 2 however will be on the market, But only after testing them out.


I am glad that EDH_performance i happy with his dm superpump.

price per series 2 element ? and any idea of when these may be ready

As I wrote at first, 50 days approx. Price is not set yet. I must test them out first.

jeemu
&quot;some people do, some people talk.&quot;

457
03-05-2012, 04:15 PM #32
Can you tell how much is true injection amount on 7,5mm. Not mean what you can get on testbench?

OM605 600hp diesel drag car build with BMW E30 chassis
jeemu
03-05-2012, 04:15 PM #32

Can you tell how much is true injection amount on 7,5mm. Not mean what you can get on testbench?


OM605 600hp diesel drag car build with BMW E30 chassis

mantahead
Holset

600
03-05-2012, 05:20 PM #33
(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink
hi,
nice one, Goran has done it againTongue
what sort of EGTS are you getting
how many cc of fuel

mantahead
03-05-2012, 05:20 PM #33

(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink
hi,
nice one, Goran has done it againTongue
what sort of EGTS are you getting
how many cc of fuel

EDH_Performance
Holset

537
03-05-2012, 07:51 PM #34
(03-05-2012, 05:20 PM)mantahead
(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink
hi,
nice one, Goran has done it againTongue
what sort of EGTS are you getting
how many cc of fuel

I dont know what cc my pumpe gives! Tell us GøranBig Grin
I haven`t maxed it out yet, still on 1.7 bar i boost
I see around 500celcius at WOT...
EDH_Performance
03-05-2012, 07:51 PM #34

(03-05-2012, 05:20 PM)mantahead
(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink
hi,
nice one, Goran has done it againTongue
what sort of EGTS are you getting
how many cc of fuel

I dont know what cc my pumpe gives! Tell us GøranBig Grin
I haven`t maxed it out yet, still on 1.7 bar i boost
I see around 500celcius at WOT...

dieselmeken
Holset

407
03-06-2012, 01:29 AM #35
(03-05-2012, 04:15 PM)jeemu Can you tell how much is true injection amount on 7,5mm. Not mean what you can get on testbench?

Im not sure I am with you there, You must explain what you mean Jeemu.
The only amount I have is the answer from the bench. That is with 6x2x600 pipes & 111 testinjectors just as the Bosch testsheet says for that pump.

EDH_performance is 140cc @ 1500 rpm.

dieselmeken
03-06-2012, 01:29 AM #35

(03-05-2012, 04:15 PM)jeemu Can you tell how much is true injection amount on 7,5mm. Not mean what you can get on testbench?

Im not sure I am with you there, You must explain what you mean Jeemu.
The only amount I have is the answer from the bench. That is with 6x2x600 pipes & 111 testinjectors just as the Bosch testsheet says for that pump.

EDH_performance is 140cc @ 1500 rpm.

tomnik
Holset

587
03-06-2012, 02:40 PM #36
(03-06-2012, 01:29 AM)dieselmeken EDH_performance is 140cc @ 1500 rpm.

... @ which rack position?

Tom
tomnik
03-06-2012, 02:40 PM #36

(03-06-2012, 01:29 AM)dieselmeken EDH_performance is 140cc @ 1500 rpm.

... @ which rack position?

Tom

dieselmeken
Holset

407
03-06-2012, 04:14 PM #37
(03-06-2012, 02:40 PM)tomnik
(03-06-2012, 01:29 AM)dieselmeken EDH_performance is 140cc @ 1500 rpm.

... @ which rack position?

Tom
around 18 mm, why do you wonder?

dieselmeken
03-06-2012, 04:14 PM #37

(03-06-2012, 02:40 PM)tomnik
(03-06-2012, 01:29 AM)dieselmeken EDH_performance is 140cc @ 1500 rpm.

... @ which rack position?

Tom
around 18 mm, why do you wonder?

winmutt
bitbanger

3,468
03-06-2012, 09:43 PM #38
(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink

This post is worthless without videos.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
03-06-2012, 09:43 PM #38

(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink

This post is worthless without videos.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselmeken
Holset

407
03-07-2012, 02:22 AM #39
(03-06-2012, 09:43 PM)winmutt
(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink

This post is worthless without videos.

Daniel, do you have a small clip just for showing, maybee I can get a five star rating on my topic thenSmile
dieselmeken
03-07-2012, 02:22 AM #39

(03-06-2012, 09:43 PM)winmutt
(03-04-2012, 08:34 AM)EDH_Performance Gøran`s 7.5mm elements killed my 2nd and 3rd gear! But there is still brutal acceleration in 4thSmile So I am very pleased with the pump and the job Gøran did! Gøran is the manWink

This post is worthless without videos.

Daniel, do you have a small clip just for showing, maybee I can get a five star rating on my topic thenSmile

iheartboost
Holset

422
03-07-2012, 09:37 AM #40
So excited!!
This post was last modified: 03-07-2012, 09:40 AM by iheartboost.

1998 E300TD 7.5mm pump and hx35 to come!
00 Mustang gt drift car

iheartboost
03-07-2012, 09:37 AM #40

So excited!!


1998 E300TD 7.5mm pump and hx35 to come!
00 Mustang gt drift car

HoleshotHolset
Holset

379
03-07-2012, 10:44 PM #41
Glad I didn't send my pump out yet... Smile
By the way, where are the dieselmeken stickers?! Big Grin

'07 W211 OM642
'95 W124.131/722.435, 211k - daily driver/Superturbo project - OM606.962 with "M" pump...under construction! (build thread here)
'99 W210.025 - gone, but not forgotten
'94 Dodge/Cummins - gone, but not forgotten
HoleshotHolset
03-07-2012, 10:44 PM #41

Glad I didn't send my pump out yet... Smile
By the way, where are the dieselmeken stickers?! Big Grin


'07 W211 OM642
'95 W124.131/722.435, 211k - daily driver/Superturbo project - OM606.962 with "M" pump...under construction! (build thread here)
'99 W210.025 - gone, but not forgotten
'94 Dodge/Cummins - gone, but not forgotten

jonbobshinigin
Holset

292
03-07-2012, 11:09 PM #42
Can we say "group buy"?

1987 300TDT - 260,000 Miles
>>275HP OM603 Project Profile here<<

jonbobshinigin
03-07-2012, 11:09 PM #42

Can we say "group buy"?


1987 300TDT - 260,000 Miles
>>275HP OM603 Project Profile here<<

sassparilla_kid
diesel &gt; all other fuels

1,618
03-08-2012, 02:44 AM #43
I need to find another job pronto so I can afford this lol

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
03-08-2012, 02:44 AM #43

I need to find another job pronto so I can afford this lol


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

EDH_Performance
Holset

537
03-08-2012, 05:05 AM #44
Here is oneSmile
http://www.youtube.com/watch?v=Da_aPaNex...r_embedded#!

The other car is an BMW 325ix with 170 hp.

I have no 3rd and so I have alot of lag I 4th because of thatSmile
Feeding pressure to the pump is 3bar.
The turbo is putting out 1.7bar, around 450-500c in EGT, and it is still smoking, so i need to turn the stoparm down a bit moreSmile

This post was last modified: 03-08-2012, 08:30 AM by EDH_Performance.
EDH_Performance
03-08-2012, 05:05 AM #44

Here is oneSmile
http://www.youtube.com/watch?v=Da_aPaNex...r_embedded#!

The other car is an BMW 325ix with 170 hp.

I have no 3rd and so I have alot of lag I 4th because of thatSmile
Feeding pressure to the pump is 3bar.
The turbo is putting out 1.7bar, around 450-500c in EGT, and it is still smoking, so i need to turn the stoparm down a bit moreSmile

dieselmeken
Holset

407
03-08-2012, 07:40 AM #45
(03-08-2012, 05:05 AM)EDH_Performance Here is oneSmile
http://www.youtube.com/watch?v=Da_aPaNex...r_embedded#!

The other car is an BMW 325ix with 170 hp.

I have no 3rd and so I have alot of lag I 4th because of thatSmile
Feeding preassure to the pump is 3bar.
The turbo is putting out 1.7bar, around 450-500c in EGT, and it is still smoking, so i need to turn the stoparm down a bit moreSmile

Or you can adjust the pressure to go higher, and crash the other gears tooBig GrinBig Grin



dieselmeken
03-08-2012, 07:40 AM #45

(03-08-2012, 05:05 AM)EDH_Performance Here is oneSmile
http://www.youtube.com/watch?v=Da_aPaNex...r_embedded#!

The other car is an BMW 325ix with 170 hp.

I have no 3rd and so I have alot of lag I 4th because of thatSmile
Feeding preassure to the pump is 3bar.
The turbo is putting out 1.7bar, around 450-500c in EGT, and it is still smoking, so i need to turn the stoparm down a bit moreSmile

Or you can adjust the pressure to go higher, and crash the other gears tooBig GrinBig Grin



EDH_Performance
Holset

537
03-08-2012, 08:19 AM #46
(03-08-2012, 07:40 AM)dieselmeken
(03-08-2012, 05:05 AM)EDH_Performance Here is oneSmile
http://www.youtube.com/watch?v=Da_aPaNex...r_embedded#!

The other car is an BMW 325ix with 170 hp.

I have no 3rd and so I have alot of lag I 4th because of thatSmile
Feeding preassure to the pump is 3bar.
The turbo is putting out 1.7bar, around 450-500c in EGT, and it is still smoking, so i need to turn the stoparm down a bit moreSmile


Or you can adjust the pressure to go higher, and crash the other gears tooBig GrinBig Grin
Haha, i just ordered a BMW e39 530d gearbox and clutch from a wreckyard in sweden, This will hold the powerWink
EDH_Performance
03-08-2012, 08:19 AM #46

(03-08-2012, 07:40 AM)dieselmeken
(03-08-2012, 05:05 AM)EDH_Performance Here is oneSmile
http://www.youtube.com/watch?v=Da_aPaNex...r_embedded#!

The other car is an BMW 325ix with 170 hp.

I have no 3rd and so I have alot of lag I 4th because of thatSmile
Feeding preassure to the pump is 3bar.
The turbo is putting out 1.7bar, around 450-500c in EGT, and it is still smoking, so i need to turn the stoparm down a bit moreSmile


Or you can adjust the pressure to go higher, and crash the other gears tooBig GrinBig Grin
Haha, i just ordered a BMW e39 530d gearbox and clutch from a wreckyard in sweden, This will hold the powerWink

iheartboost
Holset

422
03-08-2012, 08:02 PM #47
i want to blow black smoke Sad

1998 E300TD 7.5mm pump and hx35 to come!
00 Mustang gt drift car

iheartboost
03-08-2012, 08:02 PM #47

i want to blow black smoke Sad


1998 E300TD 7.5mm pump and hx35 to come!
00 Mustang gt drift car

diesel2fast4u
GT2256V

107
03-09-2012, 02:16 AM #48
(03-08-2012, 08:02 PM)iheartboost i want to blow black smoke Sad

buy a truck Smile

Grand cherokee WK (OM642)
diesel2fast4u
03-09-2012, 02:16 AM #48

(03-08-2012, 08:02 PM)iheartboost i want to blow black smoke Sad

buy a truck Smile


Grand cherokee WK (OM642)

Savitas
K26-2

34
03-09-2012, 04:01 AM #49
(03-08-2012, 08:19 AM)EDH_Performance Haha, i just ordered a BMW e39 530d gearbox and clutch from a wreckyard in sweden, This will hold the powerWink

This is my GS5-39DZ gearbox ready to fit with OM606 engine.
[Image: 882c35871a4b.jpg]

BMW gearbox should hold your torque, but I'm in deep doubt about original clutch. I offer you to not waste money and buy some ceramic clutch and and stronger pressure plate.
Savitas
03-09-2012, 04:01 AM #49

(03-08-2012, 08:19 AM)EDH_Performance Haha, i just ordered a BMW e39 530d gearbox and clutch from a wreckyard in sweden, This will hold the powerWink

This is my GS5-39DZ gearbox ready to fit with OM606 engine.
[Image: 882c35871a4b.jpg]

BMW gearbox should hold your torque, but I'm in deep doubt about original clutch. I offer you to not waste money and buy some ceramic clutch and and stronger pressure plate.

George3soccer
Holset

373
03-09-2012, 08:54 AM #50
your options with a bmw tranny is huge with clutches.

Mb 1984 w201 om603 swap.
Mb 1986 w201 190E 2.3-16v
Mb 2004 w203 C230k
George3soccer
03-09-2012, 08:54 AM #50

your options with a bmw tranny is huge with clutches.


Mb 1984 w201 om603 swap.
Mb 1986 w201 190E 2.3-16v
Mb 2004 w203 C230k

Pages (9): 1 2 3 4 5 9 Next  
 
  • 5 Vote(s) - 4.8 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)