STD Other Projects Purple turbo 240D

Purple turbo 240D

Purple turbo 240D

 
  • 3 Vote(s) - 4.33 Average
 
Pages (14): Previous 1 2 3 4 5 14 Next  
Purplecomputer
Slowness 220D

897
01-06-2012, 11:17 PM #51
(01-06-2012, 08:51 PM)ronnie I am making good progress on my turbo conversion. Couple of things to note. If you have the York a/c compressor it will not fit with a turbo conversion, you will need the newer r-4 gm compressor and bracket that mounts under the power steering pump on the drivers side.

throttle linkages will also need to be changed, notice your linkages come up through the intake/exhaust manifold. they will not fit once the turbo is on. I'll figure what I am going to do this weekend.

New engine is in now, just need to finish little stuff. Might take the complete exhaust off a 300, it's the easy way. Don't worry I do have two down pipes, so if you still want one I do have an extra.

Thats the last piece I need before I can start putting the turbo. I want to be able to have everything I need and do it in one day. Im super tight on cash and im saving my money because I still might be buying some euro bumpers.

Ill keep everyone posted. Let me know how it turns out with the throttle linkage as I was looking at that today as well.
Purplecomputer
01-06-2012, 11:17 PM #51

(01-06-2012, 08:51 PM)ronnie I am making good progress on my turbo conversion. Couple of things to note. If you have the York a/c compressor it will not fit with a turbo conversion, you will need the newer r-4 gm compressor and bracket that mounts under the power steering pump on the drivers side.

throttle linkages will also need to be changed, notice your linkages come up through the intake/exhaust manifold. they will not fit once the turbo is on. I'll figure what I am going to do this weekend.

New engine is in now, just need to finish little stuff. Might take the complete exhaust off a 300, it's the easy way. Don't worry I do have two down pipes, so if you still want one I do have an extra.

Thats the last piece I need before I can start putting the turbo. I want to be able to have everything I need and do it in one day. Im super tight on cash and im saving my money because I still might be buying some euro bumpers.

Ill keep everyone posted. Let me know how it turns out with the throttle linkage as I was looking at that today as well.

Purplecomputer
Slowness 220D

897
02-22-2012, 05:05 PM #52
Finally some progress!

I made my dad make me a guage holder for the car. Hes way better at wood work then i am

We put it over a pot so the steam would soften the would so it would take shape to the ashtray. Tomorrow my dad will glue it and Ill get some vinyl to make it match the rest of the interior

[Image: th_20120222_145805.jpg]
[Image: th_20120222_145637.jpg]
[Image: th_20120222_143915.jpg]
[Image: th_20120222_143243.jpg]
Purplecomputer
02-22-2012, 05:05 PM #52

Finally some progress!

I made my dad make me a guage holder for the car. Hes way better at wood work then i am

We put it over a pot so the steam would soften the would so it would take shape to the ashtray. Tomorrow my dad will glue it and Ill get some vinyl to make it match the rest of the interior

[Image: th_20120222_145805.jpg]
[Image: th_20120222_145637.jpg]
[Image: th_20120222_143915.jpg]
[Image: th_20120222_143243.jpg]

sassparilla_kid
diesel > all other fuels

1,618
02-22-2012, 07:45 PM #53
Awesome, Im thinking about making one that hugs the steering column, that way I can keep the guages where I can see them
This post was last modified: 02-22-2012, 07:46 PM by sassparilla_kid.

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
02-22-2012, 07:45 PM #53

Awesome, Im thinking about making one that hugs the steering column, that way I can keep the guages where I can see them


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
02-23-2012, 07:25 PM #54
(02-22-2012, 07:45 PM)sassparilla_kid Awesome, Im thinking about making one that hugs the steering column, that way I can keep the guages where I can see them

That would look cool but i wanted it to look like it came with the car so i removed thr ash tray Smile
Purplecomputer
02-23-2012, 07:25 PM #54

(02-22-2012, 07:45 PM)sassparilla_kid Awesome, Im thinking about making one that hugs the steering column, that way I can keep the guages where I can see them

That would look cool but i wanted it to look like it came with the car so i removed thr ash tray Smile

w123love
Stockish

354
02-23-2012, 10:25 PM #55
The bee knees would be one that could be hidden in the ashtray Big Grin

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
02-23-2012, 10:25 PM #55

The bee knees would be one that could be hidden in the ashtray Big Grin


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

sassparilla_kid
diesel > all other fuels

1,618
02-24-2012, 12:50 AM #56
Unfortunately my ashtray gets used for ashes, and power for miscellaneous chargers and stuff when they are needed. Plus I want to have the guages right in front of me where all the other guages are so I don't have to go searching for them when I want to know what's up, like I have to do right now when I want to see boost

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
02-24-2012, 12:50 AM #56

Unfortunately my ashtray gets used for ashes, and power for miscellaneous chargers and stuff when they are needed. Plus I want to have the guages right in front of me where all the other guages are so I don't have to go searching for them when I want to know what's up, like I have to do right now when I want to see boost


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
02-24-2012, 01:02 AM #57
(02-24-2012, 12:50 AM)sassparilla_kid Unfortunately my ashtray gets used for ashes, and power for miscellaneous chargers and stuff when they are needed. Plus I want to have the guages right in front of me where all the other guages are so I don't have to go searching for them when I want to know what's up, like I have to do right now when I want to see boost

I get ya man. my radio has a built in USB so i power most of my stuff through there and i quit smoking so i dont need to dispose of my ashes anymore Big Grin

I really want to see what you come up with though
Purplecomputer
02-24-2012, 01:02 AM #57

(02-24-2012, 12:50 AM)sassparilla_kid Unfortunately my ashtray gets used for ashes, and power for miscellaneous chargers and stuff when they are needed. Plus I want to have the guages right in front of me where all the other guages are so I don't have to go searching for them when I want to know what's up, like I have to do right now when I want to see boost

I get ya man. my radio has a built in USB so i power most of my stuff through there and i quit smoking so i dont need to dispose of my ashes anymore Big Grin

I really want to see what you come up with though

sassparilla_kid
diesel > all other fuels

1,618
02-24-2012, 01:31 AM #58
My radio has usb as well, although my ipod is perpetually plugged into it Rolleyes

As for the ashtray I like having the lighter there haha, and I don't really use it as much as my friends, unless I need to satisfy a cigar craving lol Cool

I'll post somewhere when I get my guages figured out Wink

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
02-24-2012, 01:31 AM #58

My radio has usb as well, although my ipod is perpetually plugged into it Rolleyes

As for the ashtray I like having the lighter there haha, and I don't really use it as much as my friends, unless I need to satisfy a cigar craving lol Cool

I'll post somewhere when I get my guages figured out Wink


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
03-23-2012, 05:19 PM #59
I spent a good day of my weekend replacing some old rubber Wink

[Image: 20120323_174319.jpg]

The subframe mounts were a paint to get in and the rear differential mount wasnt any easier!

[Image: 20120323_174155.jpg]

Two bolts, one on each side, broke in half while i was removing the mount forcing me to grind them out. Doing so cause me to make a bigger hole then I could use so my dad today went to the store and picked up some metal pieces to custom make me some new ones.

[Image: 20120323_174212.jpg]

Hopefully he can finish it tomorrow since im down my daily driver and using my moms car for the moment. Its strange driving a gasser...NO NOISE! i felt like i wasnt turning on the car at one point.


once all the work is done with the mount ill be moving on to replacing the flex disk!

[Image: 20120323_174230.jpg]
This post was last modified: 03-23-2012, 05:20 PM by Purplecomputer.
Purplecomputer
03-23-2012, 05:19 PM #59

I spent a good day of my weekend replacing some old rubber Wink

[Image: 20120323_174319.jpg]

The subframe mounts were a paint to get in and the rear differential mount wasnt any easier!

[Image: 20120323_174155.jpg]

Two bolts, one on each side, broke in half while i was removing the mount forcing me to grind them out. Doing so cause me to make a bigger hole then I could use so my dad today went to the store and picked up some metal pieces to custom make me some new ones.

[Image: 20120323_174212.jpg]

Hopefully he can finish it tomorrow since im down my daily driver and using my moms car for the moment. Its strange driving a gasser...NO NOISE! i felt like i wasnt turning on the car at one point.


once all the work is done with the mount ill be moving on to replacing the flex disk!

[Image: 20120323_174230.jpg]

Purplecomputer
Slowness 220D

897
03-23-2012, 06:53 PM #60
a nice surpise when i came home, the front euro bumper came and so did the euro headlights!

I started unboxing them before i realized i should share this with you guys

[Image: 20120323_185027.jpg]

ooh..

[Image: 20120323_185035.jpg]

forgot to take pictures of the individual lamps

[Image: 20120323_190759.jpg]

heres the inside of one, you can definately tell its not OEM quality but i dont fee as bad since its not some blacked out projector crap you normally find on fleabay

[Image: 20120323_185259.jpg]
[Image: 20120323_185255.jpg]
[Image: 20120323_185250.jpg]

heres the bumper!

[Image: 20120323_190004.jpg]

part numbers, so shiny!

[Image: 20120323_190027.jpg]

and the only real damage on the bumper, good thing the license plate will cover that up

[Image: 20120323_190038.jpg]


I plan on installing everything on sunday, of course if the weather allows me too.


Purplecomputer
03-23-2012, 06:53 PM #60

a nice surpise when i came home, the front euro bumper came and so did the euro headlights!

I started unboxing them before i realized i should share this with you guys

[Image: 20120323_185027.jpg]

ooh..

[Image: 20120323_185035.jpg]

forgot to take pictures of the individual lamps

[Image: 20120323_190759.jpg]

heres the inside of one, you can definately tell its not OEM quality but i dont fee as bad since its not some blacked out projector crap you normally find on fleabay

[Image: 20120323_185259.jpg]
[Image: 20120323_185255.jpg]
[Image: 20120323_185250.jpg]

heres the bumper!

[Image: 20120323_190004.jpg]

part numbers, so shiny!

[Image: 20120323_190027.jpg]

and the only real damage on the bumper, good thing the license plate will cover that up

[Image: 20120323_190038.jpg]


I plan on installing everything on sunday, of course if the weather allows me too.


Purplecomputer
Slowness 220D

897
03-24-2012, 07:35 PM #61
So i finally finished with the differential mount!

heres the new metal pieces my dad fabricated.

[Image: 20120324_174224.jpg]

he even was able to make those edges

[Image: 20120324_174229.jpg]
Purplecomputer
03-24-2012, 07:35 PM #61

So i finally finished with the differential mount!

heres the new metal pieces my dad fabricated.

[Image: 20120324_174224.jpg]

he even was able to make those edges

[Image: 20120324_174229.jpg]

Purplecomputer
Slowness 220D

897
03-26-2012, 08:15 PM #62
I put on the front euro bumper yesterday and it was easier then i expected

[Image: 20120325_183845.jpg]

im not used to the skinny bumpers so it just looks odd to me right now

[Image: 20120325_183936.jpg]

The rust on the bottom front was a little worse then i expected but nothing i cant fix!

[Image: 20120325_184000.jpg]
Purplecomputer
03-26-2012, 08:15 PM #62

I put on the front euro bumper yesterday and it was easier then i expected

[Image: 20120325_183845.jpg]

im not used to the skinny bumpers so it just looks odd to me right now

[Image: 20120325_183936.jpg]

The rust on the bottom front was a little worse then i expected but nothing i cant fix!

[Image: 20120325_184000.jpg]

w123love
Stockish

354
03-26-2012, 10:50 PM #63
I dig it. Def need a Euro plate for the front, then you’ll like it for sure. Are you going to put the rubber trim on? It surprisingly (to me) looks ok without it.

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
03-26-2012, 10:50 PM #63

I dig it. Def need a Euro plate for the front, then you’ll like it for sure. Are you going to put the rubber trim on? It surprisingly (to me) looks ok without it.


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

Purplecomputer
Slowness 220D

897
03-27-2012, 06:36 AM #64
the rubber trim is on, Is the trim supposed to be on top of the bumper because is underneath it right now.
Purplecomputer
03-27-2012, 06:36 AM #64

the rubber trim is on, Is the trim supposed to be on top of the bumper because is underneath it right now.

Purplecomputer
Slowness 220D

897
03-28-2012, 11:54 AM #65
My day off! its going to rain here in NY so i figured i would swap the rear bumper before it does.

here is the bumper pulled off before i cleaned the bottom

[Image: 20120328_103515.jpg]
[Image: 20120328_103525.jpg]

here it is cleaned!

[Image: 20120328_105244.jpg]

there were some rusty spots so i sanded them and sprayed primer and the i coated it with paint that matches the body color. I didnt want to post the finished result on that cause I messed it up but it looks better then rust

[Image: 20120328_111159.jpg]
[Image: 20120328_111149.jpg]

here is the finished result with the bumper on. I am pretty sure i messedd this up too because i didnt have the metal pieces which aligned the tips and There is to much space between the bumper and car.. take a look and let me know if i did it wrong

[Image: 20120328_121414.jpg]
[Image: 20120328_121424.jpg]
[Image: 20120328_121429.jpg]


heres a shot from far away

[Image: 20120328_122132.jpg]

i also was finally able to align the driver side door striker. no more slamming!

today was a good day
This post was last modified: 03-28-2012, 11:56 AM by Purplecomputer.
Purplecomputer
03-28-2012, 11:54 AM #65

My day off! its going to rain here in NY so i figured i would swap the rear bumper before it does.

here is the bumper pulled off before i cleaned the bottom

[Image: 20120328_103515.jpg]
[Image: 20120328_103525.jpg]

here it is cleaned!

[Image: 20120328_105244.jpg]

there were some rusty spots so i sanded them and sprayed primer and the i coated it with paint that matches the body color. I didnt want to post the finished result on that cause I messed it up but it looks better then rust

[Image: 20120328_111159.jpg]
[Image: 20120328_111149.jpg]

here is the finished result with the bumper on. I am pretty sure i messedd this up too because i didnt have the metal pieces which aligned the tips and There is to much space between the bumper and car.. take a look and let me know if i did it wrong

[Image: 20120328_121414.jpg]
[Image: 20120328_121424.jpg]
[Image: 20120328_121429.jpg]


heres a shot from far away

[Image: 20120328_122132.jpg]

i also was finally able to align the driver side door striker. no more slamming!

today was a good day

w123love
Stockish

354
03-28-2012, 12:09 PM #66
(03-27-2012, 06:36 AM)Purplecomputer the rubber trim is on, Is the trim supposed to be on top of the bumper because is underneath it right now.
Yeah, take a look at other Euro W123’s.

if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN
w123love
03-28-2012, 12:09 PM #66

(03-27-2012, 06:36 AM)Purplecomputer the rubber trim is on, Is the trim supposed to be on top of the bumper because is underneath it right now.
Yeah, take a look at other Euro W123’s.


if it don’t blow black...take it back.

1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty

The VEGEWGN

sassparilla_kid
diesel > all other fuels

1,618
03-28-2012, 01:05 PM #67
Those bumpers look pretty awesome, now you just need to get your turbo conversion set up and those euro lights and you'll have one bitchin' mercedes!!

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
03-28-2012, 01:05 PM #67

Those bumpers look pretty awesome, now you just need to get your turbo conversion set up and those euro lights and you'll have one bitchin' mercedes!!


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
03-28-2012, 02:03 PM #68
(03-28-2012, 12:09 PM)w123love
(03-27-2012, 06:36 AM)Purplecomputer the rubber trim is on, Is the trim supposed to be on top of the bumper because is underneath it right now.
Yeah, take a look at other Euro W123’s.

yeah the shots are all too far away for me to really make out anything. ill fix it later this week


(03-28-2012, 01:05 PM)sassparilla_kid Those bumpers look pretty awesome, now you just need to get your turbo conversion set up and those euro lights and you'll have one bitchin' mercedes!!


Im justing waiting on the HID kit to come in before i put those on and i just need a few more parts for the turbo conversion which i am working out with another forum member!
This post was last modified: 03-28-2012, 02:04 PM by Purplecomputer.
Purplecomputer
03-28-2012, 02:03 PM #68

(03-28-2012, 12:09 PM)w123love
(03-27-2012, 06:36 AM)Purplecomputer the rubber trim is on, Is the trim supposed to be on top of the bumper because is underneath it right now.
Yeah, take a look at other Euro W123’s.

yeah the shots are all too far away for me to really make out anything. ill fix it later this week


(03-28-2012, 01:05 PM)sassparilla_kid Those bumpers look pretty awesome, now you just need to get your turbo conversion set up and those euro lights and you'll have one bitchin' mercedes!!


Im justing waiting on the HID kit to come in before i put those on and i just need a few more parts for the turbo conversion which i am working out with another forum member!

Purplecomputer
Slowness 220D

897
06-21-2012, 10:44 AM #69
WOAH! STATUS UPDATE GUYZ!11!

okay so,

Ive done a few things but havent really documented it

I put on the euro headlights, I love em!
[Image: w123front.jpg]

Then There was some missing paint and stuff so I went to an auto body and got matching paint in a paint can and just covered it up with light layers, came out pretty good

[Image: 20120611_190708.jpg]

Then I put in the chrome tail light trim, huge difference

[Image: 20120610_175553.jpg]

thats really all ive done to date but BIG NEWS GUYZ!

I am installing or going to actually install my turbo this weekend! my parents will be gone for a week on a cruise leaving me their awezome toyota camry so I have a back up car in case all goes wrong
Purplecomputer
06-21-2012, 10:44 AM #69

WOAH! STATUS UPDATE GUYZ!11!

okay so,

Ive done a few things but havent really documented it

I put on the euro headlights, I love em!
[Image: w123front.jpg]

Then There was some missing paint and stuff so I went to an auto body and got matching paint in a paint can and just covered it up with light layers, came out pretty good

[Image: 20120611_190708.jpg]

Then I put in the chrome tail light trim, huge difference

[Image: 20120610_175553.jpg]

thats really all ive done to date but BIG NEWS GUYZ!

I am installing or going to actually install my turbo this weekend! my parents will be gone for a week on a cruise leaving me their awezome toyota camry so I have a back up car in case all goes wrong

Simpler=Better
PORTED HEAD

2,127
06-21-2012, 11:33 AM #70
(06-21-2012, 10:44 AM)Purplecomputer I am installing or going to actually install my turbo this weekend! my parents will be gone for a week on a cruise leaving me their awezome toyota camry so I have a back up car in case all goes wrong

Lookin' good! However, something WILL go wrong-that's just the way turbo swaps go Big Grin

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
06-21-2012, 11:33 AM #70

(06-21-2012, 10:44 AM)Purplecomputer I am installing or going to actually install my turbo this weekend! my parents will be gone for a week on a cruise leaving me their awezome toyota camry so I have a back up car in case all goes wrong

Lookin' good! However, something WILL go wrong-that's just the way turbo swaps go Big Grin


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

Purplecomputer
Slowness 220D

897
06-21-2012, 11:55 AM #71
(06-21-2012, 11:33 AM)Simpler=Better
(06-21-2012, 10:44 AM)Purplecomputer I am installing or going to actually install my turbo this weekend! my parents will be gone for a week on a cruise leaving me their awezome toyota camry so I have a back up car in case all goes wrong

Lookin' good! However, something WILL go wrong-that's just the way turbo swaps go Big Grin

no need to tell me! I know it first hand!
Purplecomputer
06-21-2012, 11:55 AM #71

(06-21-2012, 11:33 AM)Simpler=Better
(06-21-2012, 10:44 AM)Purplecomputer I am installing or going to actually install my turbo this weekend! my parents will be gone for a week on a cruise leaving me their awezome toyota camry so I have a back up car in case all goes wrong

Lookin' good! However, something WILL go wrong-that's just the way turbo swaps go Big Grin

no need to tell me! I know it first hand!

bryant.cw
Naturally-aspirated

17
06-21-2012, 12:58 PM #72
http://www.batinc.net/mocal-central.htm

That place sells pretty much any connector you could need. I got new fittings and hoses for the transmission and engine oil coolers. Pretty economical to make your own instead of paying a hydraulic shop to do it for you.

They sell different types of hoses and fittings, some take clamps, some use 'aeroquip' push-on connectors that are super heavy duty. Get the ones you need clamps for, the aeroquip lines are "push on", but my arm isn't exactly a hydraulic press and getting everything together was a nightmare.

They also actually have customer service which is pretty rare these days, if you call them they will work out what you need.
bryant.cw
06-21-2012, 12:58 PM #72

http://www.batinc.net/mocal-central.htm

That place sells pretty much any connector you could need. I got new fittings and hoses for the transmission and engine oil coolers. Pretty economical to make your own instead of paying a hydraulic shop to do it for you.

They sell different types of hoses and fittings, some take clamps, some use 'aeroquip' push-on connectors that are super heavy duty. Get the ones you need clamps for, the aeroquip lines are "push on", but my arm isn't exactly a hydraulic press and getting everything together was a nightmare.

They also actually have customer service which is pretty rare these days, if you call them they will work out what you need.

Purplecomputer
Slowness 220D

897
06-21-2012, 01:12 PM #73
(06-21-2012, 12:58 PM)bryant.cw http://www.batinc.net/mocal-central.htm

That place sells pretty much any connector you could need. I got new fittings and hoses for the transmission and engine oil coolers. Pretty economical to make your own instead of paying a hydraulic shop to do it for you.

They sell different types of hoses and fittings, some take clamps, some use 'aeroquip' push-on connectors that are super heavy duty. Get the ones you need clamps for, the aeroquip lines are "push on", but my arm isn't exactly a hydraulic press and getting everything together was a nightmare.

They also actually have customer service which is pretty rare these days, if you call them they will work out what you need.

I have the 300d oil line from the filter housing to the turbo thats what I will use and I already have an adapter made up for the turbo drain, thats all i really need for that, but if those hoses dont work out I will order something from this site since it looks very highquality
Purplecomputer
06-21-2012, 01:12 PM #73

(06-21-2012, 12:58 PM)bryant.cw http://www.batinc.net/mocal-central.htm

That place sells pretty much any connector you could need. I got new fittings and hoses for the transmission and engine oil coolers. Pretty economical to make your own instead of paying a hydraulic shop to do it for you.

They sell different types of hoses and fittings, some take clamps, some use 'aeroquip' push-on connectors that are super heavy duty. Get the ones you need clamps for, the aeroquip lines are "push on", but my arm isn't exactly a hydraulic press and getting everything together was a nightmare.

They also actually have customer service which is pretty rare these days, if you call them they will work out what you need.

I have the 300d oil line from the filter housing to the turbo thats what I will use and I already have an adapter made up for the turbo drain, thats all i really need for that, but if those hoses dont work out I will order something from this site since it looks very highquality

sassparilla_kid
diesel > all other fuels

1,618
06-21-2012, 09:16 PM #74
Awesome, looks pretty sweet dude, hope all goes well with the turbo swap! As long as the manifolds come off without too many problems then I think you will have it made in the shade

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
06-21-2012, 09:16 PM #74

Awesome, looks pretty sweet dude, hope all goes well with the turbo swap! As long as the manifolds come off without too many problems then I think you will have it made in the shade


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
06-21-2012, 09:25 PM #75
(06-21-2012, 09:16 PM)sassparilla_kid Awesome, looks pretty sweet dude, hope all goes well with the turbo swap! As long as the manifolds come off without too many problems then I think you will have it made in the shade

I am actually pretty worried about the whole oil lines as well as fabricating and getting the acceleration linkage working
Purplecomputer
06-21-2012, 09:25 PM #75

(06-21-2012, 09:16 PM)sassparilla_kid Awesome, looks pretty sweet dude, hope all goes well with the turbo swap! As long as the manifolds come off without too many problems then I think you will have it made in the shade

I am actually pretty worried about the whole oil lines as well as fabricating and getting the acceleration linkage working

sassparilla_kid
diesel > all other fuels

1,618
06-21-2012, 09:27 PM #76
I'm sure you'll figure it all out, and if not, then throw the keys to that extra car into the woods and you will have no other option lol

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
06-21-2012, 09:27 PM #76

I'm sure you'll figure it all out, and if not, then throw the keys to that extra car into the woods and you will have no other option lol


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
06-21-2012, 09:43 PM #77
(06-21-2012, 09:27 PM)sassparilla_kid I'm sure you'll figure it all out, and if not, then throw the keys to that extra car into the woods and you will have no other option lol

we have no woods around here

[Image: 474-whats-all-this-racket.jpg]
Purplecomputer
06-21-2012, 09:43 PM #77

(06-21-2012, 09:27 PM)sassparilla_kid I'm sure you'll figure it all out, and if not, then throw the keys to that extra car into the woods and you will have no other option lol

we have no woods around here

[Image: 474-whats-all-this-racket.jpg]

Simpler=Better
PORTED HEAD

2,127
06-22-2012, 07:42 AM #78
The oil lines are easy-get it all lined up, mark with a sharpie, and take it to a radiator shop for brazing. Best braze job I ever had done on my car cost me a whole $2.50. In a pinch you can run fuel injection line-it's rated for the 200psi or so that goes through. Ran my engine the last 2,000 miles that way.

Accel linkage is nothing.

Also, you need to paint this car purple now.

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
06-22-2012, 07:42 AM #78

The oil lines are easy-get it all lined up, mark with a sharpie, and take it to a radiator shop for brazing. Best braze job I ever had done on my car cost me a whole $2.50. In a pinch you can run fuel injection line-it's rated for the 200psi or so that goes through. Ran my engine the last 2,000 miles that way.

Accel linkage is nothing.

Also, you need to paint this car purple now.


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

Purplecomputer
Slowness 220D

897
06-22-2012, 08:39 AM #79
(06-22-2012, 07:42 AM)Simpler=Better The oil lines are easy-get it all lined up, mark with a sharpie, and take it to a radiator shop for brazing. Best braze job I ever had done on my car cost me a whole $2.50. In a pinch you can run fuel injection line-it's rated for the 200psi or so that goes through. Ran my engine the last 2,000 miles that way.

Accel linkage is nothing.

Also, you need to paint this car purple now.

brazing? never heard of that, what does that mean?
Purplecomputer
06-22-2012, 08:39 AM #79

(06-22-2012, 07:42 AM)Simpler=Better The oil lines are easy-get it all lined up, mark with a sharpie, and take it to a radiator shop for brazing. Best braze job I ever had done on my car cost me a whole $2.50. In a pinch you can run fuel injection line-it's rated for the 200psi or so that goes through. Ran my engine the last 2,000 miles that way.

Accel linkage is nothing.

Also, you need to paint this car purple now.

brazing? never heard of that, what does that mean?

Simpler=Better
PORTED HEAD

2,127
06-22-2012, 08:47 AM #80
A step above soldering and one below welding. I used the stock oil line, cut it off, and had an extension of bronze line brazed on with a banjo fitting for my turbo.

http://en.wikipedia.org/wiki/Brazing

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
06-22-2012, 08:47 AM #80

A step above soldering and one below welding. I used the stock oil line, cut it off, and had an extension of bronze line brazed on with a banjo fitting for my turbo.

http://en.wikipedia.org/wiki/Brazing


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

Purplecomputer
Slowness 220D

897
06-22-2012, 12:50 PM #81
(06-22-2012, 08:47 AM)Simpler=Better A step above soldering and one below welding. I used the stock oil line, cut it off, and had an extension of bronze line brazed on with a banjo fitting for my turbo.

http://en.wikipedia.org/wiki/Brazing

Is that necessary for me? Ronnie who also did a 240 turbo conversion did not mention anything about that to me and we have been talking much about this and he has been giving me many tips
Purplecomputer
06-22-2012, 12:50 PM #81

(06-22-2012, 08:47 AM)Simpler=Better A step above soldering and one below welding. I used the stock oil line, cut it off, and had an extension of bronze line brazed on with a banjo fitting for my turbo.

http://en.wikipedia.org/wiki/Brazing

Is that necessary for me? Ronnie who also did a 240 turbo conversion did not mention anything about that to me and we have been talking much about this and he has been giving me many tips

Purplecomputer
Slowness 220D

897
06-24-2012, 11:23 AM #82
Update

Yesterday was the first day

So far I took off the manifolds and the accelerator linkage

I was trying to take off the oil filter housing but I didnt really have the right tools. I took of the two big bolts conecting the main lines when i realized I could have saved an hour or two by just replacing the plate that holds the banjo bolt.

Tonight I will drop the oil pan, and install the piping for the turbo oil return. I will post some pictures tonight after some more work is done.
Purplecomputer
06-24-2012, 11:23 AM #82

Update

Yesterday was the first day

So far I took off the manifolds and the accelerator linkage

I was trying to take off the oil filter housing but I didnt really have the right tools. I took of the two big bolts conecting the main lines when i realized I could have saved an hour or two by just replacing the plate that holds the banjo bolt.

Tonight I will drop the oil pan, and install the piping for the turbo oil return. I will post some pictures tonight after some more work is done.

Purplecomputer
Slowness 220D

897
06-25-2012, 08:14 AM #83
Day two,

I droppped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I dont have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the egt gauge broke Sad

Tonight I will try to finish all the oil lines reintstall the oil pan and start working on the throttle linkage.
Purplecomputer
06-25-2012, 08:14 AM #83

Day two,

I droppped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I dont have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the egt gauge broke Sad

Tonight I will try to finish all the oil lines reintstall the oil pan and start working on the throttle linkage.

willbhere4u
Six in a row make her go!

2,507
06-25-2012, 09:36 AM #84
(06-25-2012, 08:14 AM)Purplecomputer Day two,

I dropped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I don't have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the EGT gauge broke Sad

Tonight I will try to finish all the oil lines reinstall the oil pan and start working on the throttle linkage.

Try to take some pictures Big Grin

Good work so far! What happened to the EGT gauge?
This post was last modified: 06-25-2012, 09:36 AM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
06-25-2012, 09:36 AM #84

(06-25-2012, 08:14 AM)Purplecomputer Day two,

I dropped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I don't have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the EGT gauge broke Sad

Tonight I will try to finish all the oil lines reinstall the oil pan and start working on the throttle linkage.

Try to take some pictures Big Grin

Good work so far! What happened to the EGT gauge?


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Simpler=Better
PORTED HEAD

2,127
06-25-2012, 09:46 AM #85
(06-25-2012, 08:14 AM)Purplecomputer Day two,

I droppped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I dont have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the egt gauge broke Sad

Tonight I will try to finish all the oil lines reintstall the oil pan and start working on the throttle linkage.

You need a step drill. HF has them the cheapest, but any hardware store will carry them. They work wonders with sheetmetal.

If you're running a stock turbo you probably don't need to braze anything-I though you were going vnt or holset or something like that.
This post was last modified: 06-25-2012, 09:48 AM by Simpler=Better.

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
06-25-2012, 09:46 AM #85

(06-25-2012, 08:14 AM)Purplecomputer Day two,

I droppped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I dont have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the egt gauge broke Sad

Tonight I will try to finish all the oil lines reintstall the oil pan and start working on the throttle linkage.

You need a step drill. HF has them the cheapest, but any hardware store will carry them. They work wonders with sheetmetal.

If you're running a stock turbo you probably don't need to braze anything-I though you were going vnt or holset or something like that.


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

Purplecomputer
Slowness 220D

897
06-25-2012, 11:00 AM #86
(06-25-2012, 09:36 AM)willbhere4u
(06-25-2012, 08:14 AM)Purplecomputer Day two,

I dropped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I don't have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the EGT gauge broke Sad

Tonight I will try to finish all the oil lines reinstall the oil pan and start working on the throttle linkage.

Try to take some pictures Big Grin

Good work so far! What happened to the EGT gauge?

Ive been mostly working at night so I will take pictures of the car so far. I have to say the engine looks awesome with a turbo on its side, like a giant tumor of awesomness. Oh and the guage is fine but the probe is what broke, I left it on there while i was working and the weight of the manifold cut the wires right at the end of the probe so I cannot splice in new wire, I will have to replace the probe.

(06-25-2012, 09:46 AM)Simpler=Better
(06-25-2012, 08:14 AM)Purplecomputer Day two,

I droppped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I dont have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the egt gauge broke Sad

Tonight I will try to finish all the oil lines reintstall the oil pan and start working on the throttle linkage.

You need a step drill. HF has them the cheapest, but any hardware store will carry them. They work wonders with sheetmetal.

If you're running a stock turbo you probably don't need to braze anything-I though you were going vnt or holset or something like that.

Step drill, never thought of that. I may have made a big doody with where i am going to put the oil return but if ronnie who has also put the turbo on a 240d and did it this way and it worked for him, I will trust him.

Edit: heres a little teaser, its a terrible photo but i wanted to get the spindle thing inside the turbo in the shot, which i wasnt able to do anyway

[Image: 20120624_223124.jpg]

also when im done with the turbo, anyone want to fix my A/C system?
This post was last modified: 06-25-2012, 11:21 AM by Purplecomputer.
Purplecomputer
06-25-2012, 11:00 AM #86

(06-25-2012, 09:36 AM)willbhere4u
(06-25-2012, 08:14 AM)Purplecomputer Day two,

I dropped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I don't have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the EGT gauge broke Sad

Tonight I will try to finish all the oil lines reinstall the oil pan and start working on the throttle linkage.

Try to take some pictures Big Grin

Good work so far! What happened to the EGT gauge?

Ive been mostly working at night so I will take pictures of the car so far. I have to say the engine looks awesome with a turbo on its side, like a giant tumor of awesomness. Oh and the guage is fine but the probe is what broke, I left it on there while i was working and the weight of the manifold cut the wires right at the end of the probe so I cannot splice in new wire, I will have to replace the probe.

(06-25-2012, 09:46 AM)Simpler=Better
(06-25-2012, 08:14 AM)Purplecomputer Day two,

I droppped the oil pan and started to modify it to be able to take the oil return pipe i had gotten. So far I dont have a big enough drill bit so I sent my friend on a shopping list of tools and things to get.

I mounted the turbo manifold, and air intake and also replaced the exhaust/air gasket while I was at it and mounted the turbo. In this time the egt gauge broke Sad

Tonight I will try to finish all the oil lines reintstall the oil pan and start working on the throttle linkage.

You need a step drill. HF has them the cheapest, but any hardware store will carry them. They work wonders with sheetmetal.

If you're running a stock turbo you probably don't need to braze anything-I though you were going vnt or holset or something like that.

Step drill, never thought of that. I may have made a big doody with where i am going to put the oil return but if ronnie who has also put the turbo on a 240d and did it this way and it worked for him, I will trust him.

Edit: heres a little teaser, its a terrible photo but i wanted to get the spindle thing inside the turbo in the shot, which i wasnt able to do anyway

[Image: 20120624_223124.jpg]

also when im done with the turbo, anyone want to fix my A/C system?

Simpler=Better
PORTED HEAD

2,127
06-25-2012, 12:45 PM #87
Spindle thingy is the impellor/ compressor/ finger chewer

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
06-25-2012, 12:45 PM #87

Spindle thingy is the impellor/ compressor/ finger chewer


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

Purplecomputer
Slowness 220D

897
06-25-2012, 02:04 PM #88
(06-25-2012, 12:45 PM)Simpler=Better Spindle thingy is the impellor/ compressor/ finger chewer

i think you meant ego booster
Purplecomputer
06-25-2012, 02:04 PM #88

(06-25-2012, 12:45 PM)Simpler=Better Spindle thingy is the impellor/ compressor/ finger chewer

i think you meant ego booster

Simpler=Better
PORTED HEAD

2,127
06-25-2012, 02:59 PM #89
Big Grin hehehhehehe

Did you polish the turbo?

Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
06-25-2012, 02:59 PM #89

Big Grin hehehhehehe

Did you polish the turbo?


Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?

Purplecomputer
Slowness 220D

897
06-25-2012, 04:11 PM #90
(06-25-2012, 02:59 PM)Simpler=Better Big Grin hehehhehehe

Did you polish the turbo?

tried, when I got it, it was covered in oil because the forum member i bought it from shipped the oil filter housing in with as well and oil spilled all over the box! Usps would not deliver I had to drive into town to go get it.
Purplecomputer
06-25-2012, 04:11 PM #90

(06-25-2012, 02:59 PM)Simpler=Better Big Grin hehehhehehe

Did you polish the turbo?

tried, when I got it, it was covered in oil because the forum member i bought it from shipped the oil filter housing in with as well and oil spilled all over the box! Usps would not deliver I had to drive into town to go get it.

Purplecomputer
Slowness 220D

897
06-25-2012, 07:48 PM #91
Had this made today, cost me a pretty penny. Mostly cause i sent my friend and i think they took advantage of him $100....

[Image: 20120625_192836.jpg]
[Image: 20120625_192818.jpg]
[Image: 20120625_192826.jpg]

This is the car with the turbo, better shot

[Image: 20120625_202917.jpg]

My work area

[Image: 20120625_203010.jpg]
[Image: 20120625_203020.jpg]

maybe this was the reason why I layed under the car for an hour trying to figure out what i was doing

[Image: 20120625_203005.jpg]

I didnt actually drink that many....i shared it with my buddy whos helping me.
This post was last modified: 06-26-2012, 02:20 PM by Purplecomputer.
Purplecomputer
06-25-2012, 07:48 PM #91

Had this made today, cost me a pretty penny. Mostly cause i sent my friend and i think they took advantage of him $100....

[Image: 20120625_192836.jpg]
[Image: 20120625_192818.jpg]
[Image: 20120625_192826.jpg]

This is the car with the turbo, better shot

[Image: 20120625_202917.jpg]

My work area

[Image: 20120625_203010.jpg]
[Image: 20120625_203020.jpg]

maybe this was the reason why I layed under the car for an hour trying to figure out what i was doing

[Image: 20120625_203005.jpg]

I didnt actually drink that many....i shared it with my buddy whos helping me.

ronnie
GT2559V

179
06-26-2012, 05:34 PM #92
I know nothing about a/c Big Grin

The tube should have fit, or just needed to be bent a bit to line up.
ronnie
06-26-2012, 05:34 PM #92

I know nothing about a/c Big Grin

The tube should have fit, or just needed to be bent a bit to line up.

sassparilla_kid
diesel > all other fuels

1,618
06-26-2012, 06:58 PM #93
That is looking awesome. Can't wait to hear about results!

-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
06-26-2012, 06:58 PM #93

That is looking awesome. Can't wait to hear about results!


-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!

Purplecomputer
Slowness 220D

897
06-27-2012, 08:13 AM #94
(06-26-2012, 05:34 PM)ronnie I know nothing about a/c Big Grin

The tube should have fit, or just needed to be bent a bit to line up.

yeah I wish I spent more time with it trying to make it work because now the new hose I had made is too long! the way I have it right now there are no kinks but i fear it will not get proper oil the way it is. If you guys think its fine I will leave it as I am running short on what I call emergency cash

[Image: imagejpeg_2.jpg]
[Image: imagejpeg_2_2.jpg]

(06-26-2012, 06:58 PM)sassparilla_kid That is looking awesome. Can't wait to hear about results!

I am really way over my head at this point and having feelings of giving up. Ill push through.
This post was last modified: 06-27-2012, 08:14 AM by Purplecomputer.
Purplecomputer
06-27-2012, 08:13 AM #94

(06-26-2012, 05:34 PM)ronnie I know nothing about a/c Big Grin

The tube should have fit, or just needed to be bent a bit to line up.

yeah I wish I spent more time with it trying to make it work because now the new hose I had made is too long! the way I have it right now there are no kinks but i fear it will not get proper oil the way it is. If you guys think its fine I will leave it as I am running short on what I call emergency cash

[Image: imagejpeg_2.jpg]
[Image: imagejpeg_2_2.jpg]

(06-26-2012, 06:58 PM)sassparilla_kid That is looking awesome. Can't wait to hear about results!

I am really way over my head at this point and having feelings of giving up. Ill push through.

willbhere4u
Six in a row make her go!

2,507
06-27-2012, 09:29 AM #95
It should work just fine just make sure it not rubbing on anything!

I took some old hose and wrapped it around the oil hose and used zip ties to hold it in place

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
06-27-2012, 09:29 AM #95

It should work just fine just make sure it not rubbing on anything!

I took some old hose and wrapped it around the oil hose and used zip ties to hold it in place


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Purplecomputer
Slowness 220D

897
06-27-2012, 09:59 AM #96
(06-27-2012, 09:29 AM)willbhere4u It should work just fine just make sure it not rubbing on anything!

I took some old hose and wrapped it around the oil hose and used zip ties to hold it in place

excellent, Ill if i can organize the hose a little and make sure its not rubbing on anything. Tonight I will tackle the return hose and ill be done with the oil part of the project and moving onto the throttle linkage!
Purplecomputer
06-27-2012, 09:59 AM #96

(06-27-2012, 09:29 AM)willbhere4u It should work just fine just make sure it not rubbing on anything!

I took some old hose and wrapped it around the oil hose and used zip ties to hold it in place

excellent, Ill if i can organize the hose a little and make sure its not rubbing on anything. Tonight I will tackle the return hose and ill be done with the oil part of the project and moving onto the throttle linkage!

JB3
Superturbo

1,795
06-27-2012, 10:20 AM #97
how in the holy hell have i missed this thread the whole time!?

two words-

Fukin awesome

Big Grin
Love the look, congratulations on how its turning out, looks good so far!

1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

JB3
06-27-2012, 10:20 AM #97

how in the holy hell have i missed this thread the whole time!?

two words-

Fukin awesome

Big Grin
Love the look, congratulations on how its turning out, looks good so far!


1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

Purplecomputer
Slowness 220D

897
06-27-2012, 11:45 AM #98
(06-27-2012, 10:20 AM)JB3 how in the holy hell have i missed this thread the whole time!?

two words-

Fukin awesome

Big Grin
Love the look, congratulations on how its turning out, looks good so far!

thanks, I am certainly trying my best with this car and its not easy sometimes.
Purplecomputer
06-27-2012, 11:45 AM #98

(06-27-2012, 10:20 AM)JB3 how in the holy hell have i missed this thread the whole time!?

two words-

Fukin awesome

Big Grin
Love the look, congratulations on how its turning out, looks good so far!

thanks, I am certainly trying my best with this car and its not easy sometimes.

ronnie
GT2559V

179
06-27-2012, 11:50 AM #99
There is an oriface in the turbo that restricts oil flow, so no need to worry about the hose, unless it really is kinked.

here is a link to my engine build, if anyone needs some more ideas

http://www.peachparts.com/shopforum/dies...616-a.html
This post was last modified: 06-27-2012, 11:54 AM by ronnie.
ronnie
06-27-2012, 11:50 AM #99

There is an oriface in the turbo that restricts oil flow, so no need to worry about the hose, unless it really is kinked.


here is a link to my engine build, if anyone needs some more ideas

http://www.peachparts.com/shopforum/dies...616-a.html

Purplecomputer
Slowness 220D

897
06-27-2012, 12:21 PM #100
(06-27-2012, 11:50 AM)ronnie There is an oriface in the turbo that restricts oil flow, so no need to worry about the hose, unless it really is kinked.

here is a link to my engine build, if anyone needs some more ideas

http://www.peachparts.com/shopforum/dies...616-a.html

No kinks, just a few bends. I am super releaved now, PHEW! Ill post pictures on how I have the return set up once I finish it!
Purplecomputer
06-27-2012, 12:21 PM #100

(06-27-2012, 11:50 AM)ronnie There is an oriface in the turbo that restricts oil flow, so no need to worry about the hose, unless it really is kinked.

here is a link to my engine build, if anyone needs some more ideas

http://www.peachparts.com/shopforum/dies...616-a.html

No kinks, just a few bends. I am super releaved now, PHEW! Ill post pictures on how I have the return set up once I finish it!

Pages (14): Previous 1 2 3 4 5 14 Next  
 
  • 3 Vote(s) - 4.33 Average
Users browsing this thread:
 2 Guest(s)
Users browsing this thread:
 2 Guest(s)