STD Tuning Engine Rebuilding an Engine, whats really involved??

Rebuilding an Engine, whats really involved??

Rebuilding an Engine, whats really involved??

 
  • 0 Vote(s) - 0 Average
 
300SD81
GT2559V

187
02-18-2010, 11:13 PM #1
Since it seems like my motor is really on the way out after running on a burnt valve for an extended period of time, I'm thinking about picking up a used engine and rebuilding it. Its been running really rough in the morning lately, pretty much on 4 cylinders for the first 5 minutes or so.

Based on what I've read, for a decent rebuild I'd need:

New Pistons and Rods
Replace Cylinder Liners
Crankshaft Tested
New bearings
Replace valves, seats and seals
timing chain, guides, sprockets, etc
Gaskets...

Is there anything I've missed? I'm planning on getting a used engine from the part yard for a long term project over whatever life my current engine has left in it. I'm just going to drive it into the ground since I'm petty sure the misfiring has bent a rod.

I can probably budget around $3k over the next 9 months or so, and the old motor should make it for at least that long, I only have one car and need it daily...


This does not mean the turbo project is on hold. Still working on it, and will test on current engine if I have it set up before the new one is ready...
This post was last modified: 02-18-2010, 11:15 PM by 300SD81.

Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!
300SD81
02-18-2010, 11:13 PM #1

Since it seems like my motor is really on the way out after running on a burnt valve for an extended period of time, I'm thinking about picking up a used engine and rebuilding it. Its been running really rough in the morning lately, pretty much on 4 cylinders for the first 5 minutes or so.

Based on what I've read, for a decent rebuild I'd need:

New Pistons and Rods
Replace Cylinder Liners
Crankshaft Tested
New bearings
Replace valves, seats and seals
timing chain, guides, sprockets, etc
Gaskets...

Is there anything I've missed? I'm planning on getting a used engine from the part yard for a long term project over whatever life my current engine has left in it. I'm just going to drive it into the ground since I'm petty sure the misfiring has bent a rod.

I can probably budget around $3k over the next 9 months or so, and the old motor should make it for at least that long, I only have one car and need it daily...


This does not mean the turbo project is on hold. Still working on it, and will test on current engine if I have it set up before the new one is ready...


Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!

ForcedInduction
Banned

3,628
02-19-2010, 07:27 AM #2
$3k isn't quite enough.

$1,250 alone for 5 piston and ring sets.
$250 valves
$175 liners
$120 bearings
$105 chain tensioner
$75 chain rails
$50 headgasket
$50 valve guides
$45 Timing chain
$35 oil pump chain
=$2,155 for just the hard parts. That doesn't include any shipping, machining, liner pressing, an injection pump rebuild (Around $1000 on its own), turbo rebuild, minor gaskets/seals or special tools.

Rods are a non-wear item. They don't need to be replaced unless bent or damaged.
ForcedInduction
02-19-2010, 07:27 AM #2

$3k isn't quite enough.

$1,250 alone for 5 piston and ring sets.
$250 valves
$175 liners
$120 bearings
$105 chain tensioner
$75 chain rails
$50 headgasket
$50 valve guides
$45 Timing chain
$35 oil pump chain
=$2,155 for just the hard parts. That doesn't include any shipping, machining, liner pressing, an injection pump rebuild (Around $1000 on its own), turbo rebuild, minor gaskets/seals or special tools.

Rods are a non-wear item. They don't need to be replaced unless bent or damaged.

300SD81
GT2559V

187
02-21-2010, 12:35 AM #3
I think I may go through with this anyway, maybe over a longer term. A head rebuild looks totally possable over summer break though, and I may be wrong about the oil consumption being a bent rod. What do you guys think about rebuilding a head and potentially putting it on a damaged block? Compression in cyl 1 is down to 200psi hot now, and combustion is leaking into the intake based on the crazy vibration my boost gauge has been doing for a while...

Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!
300SD81
02-21-2010, 12:35 AM #3

I think I may go through with this anyway, maybe over a longer term. A head rebuild looks totally possable over summer break though, and I may be wrong about the oil consumption being a bent rod. What do you guys think about rebuilding a head and potentially putting it on a damaged block? Compression in cyl 1 is down to 200psi hot now, and combustion is leaking into the intake based on the crazy vibration my boost gauge has been doing for a while...


Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!

DeliveryValve
Superturbo

1,338
02-21-2010, 12:46 AM #4
There are plenty of good used motors out there that are much cheaper then the routes your are suggesting. Plus the time of your car being out of commission would be shortened.

Unless you are talking about custom performance pieces, a regular rebuild just doesn't make economical sense to me. So my opinion is get a good low mileage motor with excellent compression and drop it in.

Gota love Mercedes Diesels!



.
DeliveryValve
02-21-2010, 12:46 AM #4

There are plenty of good used motors out there that are much cheaper then the routes your are suggesting. Plus the time of your car being out of commission would be shortened.

Unless you are talking about custom performance pieces, a regular rebuild just doesn't make economical sense to me. So my opinion is get a good low mileage motor with excellent compression and drop it in.


Gota love Mercedes Diesels!



.

ForcedInduction
Banned

3,628
02-21-2010, 12:03 PM #5
I agree. ~$600 vs $3000 for basically the same result in a fraction of the time and headache.

Most any good used engine will last as long as an owner can stand driving the same vehicle.
ForcedInduction
02-21-2010, 12:03 PM #5

I agree. ~$600 vs $3000 for basically the same result in a fraction of the time and headache.

Most any good used engine will last as long as an owner can stand driving the same vehicle.

willbhere4u
Six in a row make her go!

2,507
02-21-2010, 08:43 PM #6
I think you can find the piston ring set for $900 But if I ever rebuild one I'm going to do liners & rings! unless the pistons are damaged I would reuse them the two engines I have taken apart the pistons looked like new no scoring or any thing else wrong just clean them check them and reuse them!!!
This post was last modified: 02-21-2010, 08:46 PM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
02-21-2010, 08:43 PM #6

I think you can find the piston ring set for $900 But if I ever rebuild one I'm going to do liners & rings! unless the pistons are damaged I would reuse them the two engines I have taken apart the pistons looked like new no scoring or any thing else wrong just clean them check them and reuse them!!!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

George3soccer
Holset

373
02-24-2010, 06:46 PM #7
$900 very fesable from Mercedes and that was for 6 rings.
George3soccer
02-24-2010, 06:46 PM #7

$900 very fesable from Mercedes and that was for 6 rings.

winmutt
bitbanger

3,468
02-28-2010, 08:51 AM #8
Check with rusty @ buymbparts.biz, chat him up online about the pricing. Also check with MB Classic Parts center in Irvine.

I vote for a good used engine with verifiable compression numbers.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
02-28-2010, 08:51 AM #8

Check with rusty @ buymbparts.biz, chat him up online about the pricing. Also check with MB Classic Parts center in Irvine.

I vote for a good used engine with verifiable compression numbers.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

winmutt
bitbanger

3,468
03-01-2010, 09:55 AM #9
http://atlanta.craigslist.org/eat/pts/1618066377.html

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
03-01-2010, 09:55 AM #9

http://atlanta.craigslist.org/eat/pts/1618066377.html


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

300SD81
GT2559V

187
03-01-2010, 11:13 AM #10
(03-01-2010, 09:55 AM)winmutt http://atlanta.craigslist.org/eat/pts/1618066377.html

Thanks! I just emailed the guy, might be interested in some of the other parts too if its a SD...

Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!
300SD81
03-01-2010, 11:13 AM #10

(03-01-2010, 09:55 AM)winmutt http://atlanta.craigslist.org/eat/pts/1618066377.html

Thanks! I just emailed the guy, might be interested in some of the other parts too if its a SD...


Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!

TotalDiesel
Unregistered

 
03-05-2010, 08:49 AM #11
http://www.autopartsworld.com/mercedes-benz_parts.html

This site is loaded with parts for pretty fair prices. choose your car.
TotalDiesel
03-05-2010, 08:49 AM #11

http://www.autopartsworld.com/mercedes-benz_parts.html

This site is loaded with parts for pretty fair prices. choose your car.

Kozuka
I'm_Badass

334
03-05-2010, 12:33 PM #12
What kind of machine work would be needed? Press out - Pressing in of the cylinder liners, messing with the valve train lifters/tappets/springs/retainers/guides/valves, and headwork. Plastigauge the crank/rod bearings and see what size replacements you need. Do the liners need to be honed?
Kozuka
03-05-2010, 12:33 PM #12

What kind of machine work would be needed? Press out - Pressing in of the cylinder liners, messing with the valve train lifters/tappets/springs/retainers/guides/valves, and headwork. Plastigauge the crank/rod bearings and see what size replacements you need. Do the liners need to be honed?

winmutt
bitbanger

3,468
03-08-2010, 08:23 AM #13
(03-01-2010, 11:13 AM)300SD81
(03-01-2010, 09:55 AM)winmutt http://atlanta.craigslist.org/eat/pts/1618066377.html

Thanks! I just emailed the guy, might be interested in some of the other parts too if its a SD...

LMK if you want to borrow my compression tester.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
03-08-2010, 08:23 AM #13

(03-01-2010, 11:13 AM)300SD81
(03-01-2010, 09:55 AM)winmutt http://atlanta.craigslist.org/eat/pts/1618066377.html

Thanks! I just emailed the guy, might be interested in some of the other parts too if its a SD...

LMK if you want to borrow my compression tester.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

btrapr
Unregistered

29
03-08-2010, 10:20 AM #14
Take a look at Germanimportedparts as they seem to have good pricing on a lot of items..not sure if they have pistons...I know i have seen several engine parts listed.
btrapr
03-08-2010, 10:20 AM #14

Take a look at Germanimportedparts as they seem to have good pricing on a lot of items..not sure if they have pistons...I know i have seen several engine parts listed.

300SD81
GT2559V

187
03-08-2010, 10:20 AM #15
(03-08-2010, 08:23 AM)winmutt
(03-01-2010, 11:13 AM)300SD81
(03-01-2010, 09:55 AM)winmutt http://atlanta.craigslist.org/eat/pts/1618066377.html

Thanks! I just emailed the guy, might be interested in some of the other parts too if its a SD...

LMK if you want to borrow my compression tester.

I have one, but thanks anyway. Do you happen to have an engine lift/stand?

Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!
300SD81
03-08-2010, 10:20 AM #15

(03-08-2010, 08:23 AM)winmutt
(03-01-2010, 11:13 AM)300SD81
(03-01-2010, 09:55 AM)winmutt http://atlanta.craigslist.org/eat/pts/1618066377.html

Thanks! I just emailed the guy, might be interested in some of the other parts too if its a SD...

LMK if you want to borrow my compression tester.

I have one, but thanks anyway. Do you happen to have an engine lift/stand?


Ich liebe meine Autos!

1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...

1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in Sad | Retired to garage.

Excessive speeding? It ain't excessive till I redline!

winmutt
bitbanger

3,468
03-09-2010, 11:22 AM #16
Stand yes. I had a hoist at my house forever but the owner took it back.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
03-09-2010, 11:22 AM #16

Stand yes. I had a hoist at my house forever but the owner took it back.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 2 Guest(s)
Users browsing this thread:
 2 Guest(s)