STD Tuning Engine I think I cooked my turbo.

I think I cooked my turbo.

I think I cooked my turbo.

 
  • 0 Vote(s) - 0 Average
 
winmutt
bitbanger

3,468
05-24-2011, 12:49 PM #1
Parked it over the weekend. Monday morning no power lots of black smoke. I havent pulled the intake yet but.... last weekend I installed a MBC and kept turning it up until the overboost kicked in. Well the overoost never kicked in, probably because I also backed out the alda at the same time. It was whistling but I assumed it was an air leak somewhere. not the singing of the journals burning up.

Anyone know if the engine would still run if the turbo seized? Could it just be rotating slowly enough to not provide boost?

I have been looking for a turbo but now... well its more imperative.
This post was last modified: 05-24-2011, 12:51 PM by winmutt.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-24-2011, 12:49 PM #1

Parked it over the weekend. Monday morning no power lots of black smoke. I havent pulled the intake yet but.... last weekend I installed a MBC and kept turning it up until the overboost kicked in. Well the overoost never kicked in, probably because I also backed out the alda at the same time. It was whistling but I assumed it was an air leak somewhere. not the singing of the journals burning up.

Anyone know if the engine would still run if the turbo seized? Could it just be rotating slowly enough to not provide boost?

I have been looking for a turbo but now... well its more imperative.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

tomnik
Holset

587
05-24-2011, 01:20 PM #2
(05-24-2011, 12:49 PM)winmutt Anyone know if the engine would still run if the turbo seized? Could it just be rotating slowly enough to not provide boost?

yes it will run but the exhaust side blocks the exhaust (high EGT, no power, smoke).

Tom
tomnik
05-24-2011, 01:20 PM #2

(05-24-2011, 12:49 PM)winmutt Anyone know if the engine would still run if the turbo seized? Could it just be rotating slowly enough to not provide boost?

yes it will run but the exhaust side blocks the exhaust (high EGT, no power, smoke).

Tom

willbhere4u
Six in a row make her go!

2,507
05-24-2011, 03:28 PM #3
I have that really nice powder coated red rebuilt turbo if your interested in it?

I've got $230 in it so far with shipping

http://www.superturbodiesel.com/std/show...418&page=2

The one on my car isn't bad

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-24-2011, 03:28 PM #3

I have that really nice powder coated red rebuilt turbo if your interested in it?

I've got $230 in it so far with shipping

http://www.superturbodiesel.com/std/show...418&page=2

The one on my car isn't bad


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

winmutt
bitbanger

3,468
05-24-2011, 04:07 PM #4
Oh that is pretty. I was thinking VNT or HY35 etc. Is that one from the rod benders or 3l 603?

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-24-2011, 04:07 PM #4

Oh that is pretty. I was thinking VNT or HY35 etc. Is that one from the rod benders or 3l 603?


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

winmutt
bitbanger

3,468
05-24-2011, 05:10 PM #5
HY35 and HY35W same turbo?

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-24-2011, 05:10 PM #5

HY35 and HY35W same turbo?


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

willbhere4u
Six in a row make her go!

2,507
05-24-2011, 07:26 PM #6
He said in the add it was from an 1986 300sdl after getting it I decided I'm going to save and get a w140 manifold and hy35
This post was last modified: 05-24-2011, 07:28 PM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-24-2011, 07:26 PM #6

He said in the add it was from an 1986 300sdl after getting it I decided I'm going to save and get a w140 manifold and hy35


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Captain America
Boostin' & Roostin'

2,221
05-25-2011, 12:32 AM #7
(05-24-2011, 05:10 PM)winmutt HY35 and HY35W same turbo?

THAT TURBO IS FAR TO LARGE AND WONT SPOOL WORTH A SHIT

Lol!!!!!!

Tongue Big Grin Cool Wink Angel Blush


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
05-25-2011, 12:32 AM #7

(05-24-2011, 05:10 PM)winmutt HY35 and HY35W same turbo?

THAT TURBO IS FAR TO LARGE AND WONT SPOOL WORTH A SHIT

Lol!!!!!!

Tongue Big Grin Cool Wink Angel Blush



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

dieselboy
Rotatin 5500 times a minute

680
05-25-2011, 01:38 AM #8
Lol. Putting a hy35 on a friends 85tdt once he gets it.
Yes they only made a hy35w. W= internally wastegated.
An he341 or hy35 are close to the same thing.
They are slow to make boost but it's still drivable and gets better mileage. I need to check my timing as I think it's way out.

I'll let you know what it's like on a car with a untouched pump as soon as we get the turbo.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
05-25-2011, 01:38 AM #8

Lol. Putting a hy35 on a friends 85tdt once he gets it.
Yes they only made a hy35w. W= internally wastegated.
An he341 or hy35 are close to the same thing.
They are slow to make boost but it's still drivable and gets better mileage. I need to check my timing as I think it's way out.

I'll let you know what it's like on a car with a untouched pump as soon as we get the turbo.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
05-25-2011, 09:09 AM #9
(05-25-2011, 01:38 AM)dieselboy They are slow to make boost
This is not what I want. However you stated you get 10psi at 2500. What about at 2000? This us going on a 603 so it should spool better than the 617.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-25-2011, 09:09 AM #9

(05-25-2011, 01:38 AM)dieselboy They are slow to make boost
This is not what I want. However you stated you get 10psi at 2500. What about at 2000? This us going on a 603 so it should spool better than the 617.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
05-25-2011, 11:48 AM #10
Oh a 603..... Ive yet to work with one of those. It's a cheap turbo that has been proven tough and reliable. 360° thrust bearing, fat shaft, etc.... Couldn't hurt to try it IMO.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
05-25-2011, 11:48 AM #10

Oh a 603..... Ive yet to work with one of those. It's a cheap turbo that has been proven tough and reliable. 360° thrust bearing, fat shaft, etc.... Couldn't hurt to try it IMO.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
05-25-2011, 04:23 PM #11
Its hard to find a good turbo suited for the 603. Either all to small or too larger or unobtanium.

Dieselboy, what kinds of psi are you seeing at 200rpm?

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-25-2011, 04:23 PM #11

Its hard to find a good turbo suited for the 603. Either all to small or too larger or unobtanium.

Dieselboy, what kinds of psi are you seeing at 200rpm?


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

willbhere4u
Six in a row make her go!

2,507
05-25-2011, 05:10 PM #12
At 200 rpm I bet none!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-25-2011, 05:10 PM #12

At 200 rpm I bet none!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

dieselboy
Rotatin 5500 times a minute

680
05-25-2011, 05:40 PM #13
I'd need to drive it and report back. I don't remember. I want to say 5 but I've just been driving the thing lately. My car is never at 2k really. 3 is the sweet spot.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
05-25-2011, 05:40 PM #13

I'd need to drive it and report back. I don't remember. I want to say 5 but I've just been driving the thing lately. My car is never at 2k really. 3 is the sweet spot.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
05-26-2011, 07:48 AM #14
Im looking for a hy30 me thinks. Hard to find tho.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-26-2011, 07:48 AM #14

Im looking for a hy30 me thinks. Hard to find tho.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
05-26-2011, 11:50 AM #15
Any other mods done to the car?

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
05-26-2011, 11:50 AM #15

Any other mods done to the car?


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
05-26-2011, 12:07 PM #16
Not to the engine yet. I have a euro manifold I will be using obviously. I want to get a modified pump but with a kid due in July I have other priorities. Also needs a new hg maybe new head so other priorities are first.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-26-2011, 12:07 PM #16

Not to the engine yet. I have a euro manifold I will be using obviously. I want to get a modified pump but with a kid due in July I have other priorities. Also needs a new hg maybe new head so other priorities are first.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

willbhere4u
Six in a row make her go!

2,507
05-26-2011, 12:22 PM #17
what's an hg?
This post was last modified: 05-26-2011, 12:22 PM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-26-2011, 12:22 PM #17

what's an hg?


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

larsalan
Superturbo

1,272
05-26-2011, 12:29 PM #18
headgasket?

Rusted out beat down 300d turbo 82' -- RIP
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'
larsalan
05-26-2011, 12:29 PM #18

headgasket?


Rusted out beat down 300d turbo 82' -- RIP
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'

willbhere4u
Six in a row make her go!

2,507
05-26-2011, 02:16 PM #19
duh !

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-26-2011, 02:16 PM #19

duh !


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Captain America
Boostin' & Roostin'

2,221
05-27-2011, 01:27 AM #20
(05-26-2011, 02:16 PM)willbhere4u duh !

It's ok, took me a second as well haha


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
05-27-2011, 01:27 AM #20

(05-26-2011, 02:16 PM)willbhere4u duh !

It's ok, took me a second as well haha



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

willbhere4u
Six in a row make her go!

2,507
05-27-2011, 10:25 AM #21
What we really need is a ball bearing turbo comparable to a Holset hy35

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-27-2011, 10:25 AM #21

What we really need is a ball bearing turbo comparable to a Holset hy35


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Captain America
Boostin' & Roostin'

2,221
05-27-2011, 04:17 PM #22
(05-27-2011, 10:25 AM)willbhere4u What we really need is a ball bearing turbo comparable to a Holset hy35

Right!?! That would make for some super spool!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
05-27-2011, 04:17 PM #22

(05-27-2011, 10:25 AM)willbhere4u What we really need is a ball bearing turbo comparable to a Holset hy35

Right!?! That would make for some super spool!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

winmutt
bitbanger

3,468
05-27-2011, 04:19 PM #23
They are ridiculously expensive.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-27-2011, 04:19 PM #23

They are ridiculously expensive.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
05-28-2011, 12:10 AM #24
What's that?

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
05-28-2011, 12:10 AM #24

What's that?


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
05-31-2011, 04:18 PM #25
Ball bearing anything... So I have looked and looked and it seems the HE341 is the easiest to find replacement upgrade for stock/semi stock 603. I cannot find a HY30W to save my life. Given Lances report ont he HE341VE I am hoping the HE341 is a easy drop in as well.

ps I asked Lance to sell me his turbo and he said he was disappointed in me and had lost faith a long time ago. Talk about pot kettle hello black.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
05-31-2011, 04:18 PM #25

Ball bearing anything... So I have looked and looked and it seems the HE341 is the easiest to find replacement upgrade for stock/semi stock 603. I cannot find a HY30W to save my life. Given Lances report ont he HE341VE I am hoping the HE341 is a easy drop in as well.

ps I asked Lance to sell me his turbo and he said he was disappointed in me and had lost faith a long time ago. Talk about pot kettle hello black.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

willbhere4u
Six in a row make her go!

2,507
05-31-2011, 04:33 PM #26
The pot calling the kettle African aluminum!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-31-2011, 04:33 PM #26

The pot calling the kettle African aluminum!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

winmutt
bitbanger

3,468
06-01-2011, 08:51 AM #27
Here is the list of possibles I compiled:

Quote:Garrett/AiResearch T3-45 1978-1985 300D/TD/CD/SD (concurrently used with the K26 from 83+)

Compressor
Exducer: 60mm
Inducer: 40.5mm
12 blades

Turbine
Inducer: 62.5mm
Exducer: 43mm
11 blades
.43 A/R

Quote:HY35 off a 98 cummins 5.9 auto.

9cm housing
Compressor exducer: 78mm
Compressor inducer: 54mm
Turbine wheel: 58/65mm

Quote:hy35 from years 00 to 02. it has the smallest compressor wheel of the hy's at 54mm.

Quote:Holset HX/HY30- Various Cummins 4BTa and John Deere applications

Compressor
Exducer: 73mm
Inducer: 44mm
6 blades
36 trim

Turbine
Inducer: ?mm
Exducer: ?mm
? blades



Quote:Schwitzer S2EGL069 (S2E, 103-2085)
Caterpillar 3116 170,185 HP, Various applications (Bus, Semi, GMC TopKick)

Compressor
Exducer: 76.2mm
Inducer: 57.5mm
57 trim
12 blades
0.60A/R
4" mouth, 2" outlet, Map-width enhancement slot

Turbine
Inducer: 69.75mm
Exducer: 60.5mm
10 blades
0.70A/R
T3 flange w/split ports, 4" v-band outlet
Compressor: 69mm exducer, 44.5 mm inducer
Turbine: 67mm / 56mm

Quote:HE341 compressor inducer at 56mm, exducer at 76 mm.
t3 flange
This is the he341ve...
Turbine
Inducer: 69mm
Exducer: 59.4mm
This post was last modified: 06-01-2011, 09:02 AM by winmutt.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
06-01-2011, 08:51 AM #27

Here is the list of possibles I compiled:

Quote:Garrett/AiResearch T3-45 1978-1985 300D/TD/CD/SD (concurrently used with the K26 from 83+)

Compressor
Exducer: 60mm
Inducer: 40.5mm
12 blades

Turbine
Inducer: 62.5mm
Exducer: 43mm
11 blades
.43 A/R

Quote:HY35 off a 98 cummins 5.9 auto.

9cm housing
Compressor exducer: 78mm
Compressor inducer: 54mm
Turbine wheel: 58/65mm

Quote:hy35 from years 00 to 02. it has the smallest compressor wheel of the hy's at 54mm.

Quote:Holset HX/HY30- Various Cummins 4BTa and John Deere applications

Compressor
Exducer: 73mm
Inducer: 44mm
6 blades
36 trim

Turbine
Inducer: ?mm
Exducer: ?mm
? blades



Quote:Schwitzer S2EGL069 (S2E, 103-2085)
Caterpillar 3116 170,185 HP, Various applications (Bus, Semi, GMC TopKick)

Compressor
Exducer: 76.2mm
Inducer: 57.5mm
57 trim
12 blades
0.60A/R
4" mouth, 2" outlet, Map-width enhancement slot

Turbine
Inducer: 69.75mm
Exducer: 60.5mm
10 blades
0.70A/R
T3 flange w/split ports, 4" v-band outlet
Compressor: 69mm exducer, 44.5 mm inducer
Turbine: 67mm / 56mm

Quote:HE341 compressor inducer at 56mm, exducer at 76 mm.
t3 flange
This is the he341ve...
Turbine
Inducer: 69mm
Exducer: 59.4mm


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

winmutt
bitbanger

3,468
06-02-2011, 11:16 AM #28
HE341 is on its way. Measurements are 54/58/9. Still not sure about the 9cm housing but we shall see!

[Image: he341.jpg]
This post was last modified: 06-02-2011, 11:17 AM by winmutt.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
06-02-2011, 11:16 AM #28

HE341 is on its way. Measurements are 54/58/9. Still not sure about the 9cm housing but we shall see!

[Image: he341.jpg]


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
06-02-2011, 06:36 PM #29
Nice. Where did you end up getting it?

The Garrett turbos originally on our cars is old technology
This post was last modified: 06-02-2011, 06:38 PM by dieselboy.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
06-02-2011, 06:36 PM #29

Nice. Where did you end up getting it?

The Garrett turbos originally on our cars is old technology


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

Captain America
Boostin' & Roostin'

2,221
06-03-2011, 01:02 AM #30
(06-02-2011, 06:36 PM)dieselboy Nice. Where did you end up getting it?

The Garrett turbos originally on our cars is old technology

Well yeah! they're like 30 yrs old!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
06-03-2011, 01:02 AM #30

(06-02-2011, 06:36 PM)dieselboy Nice. Where did you end up getting it?

The Garrett turbos originally on our cars is old technology

Well yeah! they're like 30 yrs old!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

winmutt
bitbanger

3,468
06-03-2011, 11:23 AM #31
I dont think the wheel geometry has changed on theses older garetts since wwii.

I got it off 4btswaps. If you have time its a good chance you could pick up a hx30 or hy30 from there.

Anyone know what size pipe is used for the exhaust on the 603?
This post was last modified: 06-03-2011, 11:25 AM by winmutt.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
06-03-2011, 11:23 AM #31

I dont think the wheel geometry has changed on theses older garetts since wwii.

I got it off 4btswaps. If you have time its a good chance you could pick up a hx30 or hy30 from there.

Anyone know what size pipe is used for the exhaust on the 603?


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
06-03-2011, 11:55 AM #32
60mm would be my guess.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
06-03-2011, 11:55 AM #32

60mm would be my guess.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
06-10-2011, 11:40 AM #33
HE341 is a big turbo. I think the specs I have are incorrect and that its a hair off the HE351 on the comprssor wheel. As there is too much axial play and a guy just replied back about a HY30W I am going to try to return this.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
06-10-2011, 11:40 AM #33

HE341 is a big turbo. I think the specs I have are incorrect and that its a hair off the HE351 on the comprssor wheel. As there is too much axial play and a guy just replied back about a HY30W I am going to try to return this.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
06-10-2011, 12:13 PM #34
Hy30? Thats tiny. To be honest I've never seen one.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
06-10-2011, 12:13 PM #34

Hy30? Thats tiny. To be honest I've never seen one.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

winmutt
bitbanger

3,468
06-13-2011, 01:13 PM #35
(06-10-2011, 12:13 PM)dieselboy Hy30? Thats tiny. To be honest I've never seen one.

Its larger than stock. Should be a good fit for a DD. 3" in and out t3 flange. No weird routing issues (since I am not using IC yet).


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
06-13-2011, 01:13 PM #35

(06-10-2011, 12:13 PM)dieselboy Hy30? Thats tiny. To be honest I've never seen one.

Its larger than stock. Should be a good fit for a DD. 3" in and out t3 flange. No weird routing issues (since I am not using IC yet).


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

winmutt
bitbanger

3,468
08-12-2011, 06:51 AM #36
Soooo... Got the left side of the engine off, turbo manifold etc last night. 2 of the studs are snapped Sad....

Once upon a time I took off the wastegate arm and lost the circlip. So I didnt cook the turbo, arm was just hanging off.............


For now I will probably mount the euro manifold and put the stock turbo on for another week or two until I can finalize fitment.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-12-2011, 06:51 AM #36

Soooo... Got the left side of the engine off, turbo manifold etc last night. 2 of the studs are snapped Sad....

Once upon a time I took off the wastegate arm and lost the circlip. So I didnt cook the turbo, arm was just hanging off.............


For now I will probably mount the euro manifold and put the stock turbo on for another week or two until I can finalize fitment.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

dieselboy
Rotatin 5500 times a minute

680
08-12-2011, 11:18 AM #37
Been there done that lol.

-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.
dieselboy
08-12-2011, 11:18 AM #37

Been there done that lol.


-Jesse

80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon

10 mistsubishi fuso service truck.

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 2 Guest(s)
Users browsing this thread:
 2 Guest(s)