STD Other Projects Captain's '82 300D Purists Must Die Prius Repellent

Captain's '82 300D Purists Must Die Prius Repellent

Captain's '82 300D Purists Must Die Prius Repellent

 
  • 6 Vote(s) - 3.83 Average
 
Pages (10): Previous 1 2 3 4 5 10 Next  
garage
Bush Taxi

893
08-11-2010, 07:21 PM #51
Big Grin

Hows the road noise??

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-11-2010, 07:21 PM #51

Big Grin

Hows the road noise??


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Captain America
Boostin' & Roostin'

2,221
08-11-2010, 10:50 PM #52
What road noise??? lol there is none!

The only issue I have is that with the additional width and diameter, the shoulder tries to rip off the front fender when the tire tucks and is turned. I just need to roll the edge and I think they will be fine.

Is there a way to recalibrate my speedometer???


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-11-2010, 10:50 PM #52

What road noise??? lol there is none!

The only issue I have is that with the additional width and diameter, the shoulder tries to rip off the front fender when the tire tucks and is turned. I just need to roll the edge and I think they will be fine.

Is there a way to recalibrate my speedometer???



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

garage
Bush Taxi

893
08-12-2010, 10:29 AM #53
(08-11-2010, 10:50 PM)Captain America What road noise??? lol there is none!

The only issue I have is that with the additional width and diameter, the shoulder tries to rip off the front fender when the tire tucks and is turned. I just need to roll the edge and I think they will be fine.

Is there a way to recalibrate my speedometer???

Well thats good no extra noise! Im gonna really have to get myself some more agressive tread soon. haha
Grab a baseball bat and roll the fenders dude! Ive been wanting to do mine for weeks...but i need to grab a baseball bat from someone first.

not sure about the speedo

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-12-2010, 10:29 AM #53

(08-11-2010, 10:50 PM)Captain America What road noise??? lol there is none!

The only issue I have is that with the additional width and diameter, the shoulder tries to rip off the front fender when the tire tucks and is turned. I just need to roll the edge and I think they will be fine.

Is there a way to recalibrate my speedometer???

Well thats good no extra noise! Im gonna really have to get myself some more agressive tread soon. haha
Grab a baseball bat and roll the fenders dude! Ive been wanting to do mine for weeks...but i need to grab a baseball bat from someone first.

not sure about the speedo


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Captain America
Boostin' & Roostin'

2,221
08-12-2010, 11:00 AM #54
Ive got a bat to do it with ... just takes two people haha. The tires are gonna rub no matter what.. at least if the tread doesn't catch the fender lip.. I think I need to flare the front fenders! haha that would be crazy huh?


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-12-2010, 11:00 AM #54

Ive got a bat to do it with ... just takes two people haha. The tires are gonna rub no matter what.. at least if the tread doesn't catch the fender lip.. I think I need to flare the front fenders! haha that would be crazy huh?



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

willbhere4u
Six in a row make her go!

2,507
08-12-2010, 11:42 AM #55
That's what I did on my 240d I rolled the front fenders and left the rears alone!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-12-2010, 11:42 AM #55

That's what I did on my 240d I rolled the front fenders and left the rears alone!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

garage
Bush Taxi

893
08-12-2010, 02:09 PM #56
Well damn dude, if i didnt need to install a new slave cylinder for the clutch id ask you use your bat to help roll mine!!
shit i needa get it fixed..

I wanna do fronts and backs, and flare it out as much as possible.

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-12-2010, 02:09 PM #56

Well damn dude, if i didnt need to install a new slave cylinder for the clutch id ask you use your bat to help roll mine!!
shit i needa get it fixed..

I wanna do fronts and backs, and flare it out as much as possible.


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Captain America
Boostin' & Roostin'

2,221
08-12-2010, 05:58 PM #57
This guy flared his just a bit

http://www.superturbodiesel.com/std/ml32...l#pid13486


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-12-2010, 05:58 PM #57

This guy flared his just a bit

http://www.superturbodiesel.com/std/ml32...l#pid13486



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

garage
Bush Taxi

893
08-12-2010, 06:26 PM #58
Yeah looks good, i really wanna flare mine out a bit more.

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-12-2010, 06:26 PM #58

Yeah looks good, i really wanna flare mine out a bit more.


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

winmutt
bitbanger

3,468
08-18-2010, 11:43 AM #59
(08-12-2010, 06:26 PM)garage Yeah looks good, i really wanna flare mine out a bit more.

Its not easy on the W123s. Thick german steel. There is a guy on bw or pp that will rent out the proper tool for doing it. I did mine with a baseball bat and heat gun, this will only allow you to do a little. Somewhere I have the AMG install FSM covering this for the W124.
This post was last modified: 08-18-2010, 11:44 AM by winmutt.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-18-2010, 11:43 AM #59

(08-12-2010, 06:26 PM)garage Yeah looks good, i really wanna flare mine out a bit more.

Its not easy on the W123s. Thick german steel. There is a guy on bw or pp that will rent out the proper tool for doing it. I did mine with a baseball bat and heat gun, this will only allow you to do a little. Somewhere I have the AMG install FSM covering this for the W124.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
08-18-2010, 12:36 PM #60
(08-18-2010, 11:43 AM)winmutt
(08-12-2010, 06:26 PM)garage Yeah looks good, i really wanna flare mine out a bit more.

Its not easy on the W123s. Thick german steel. There is a guy on bw or pp that will rent out the proper tool for doing it. I did mine with a baseball bat and heat gun, this will only allow you to do a little. Somewhere I have the AMG install FSM covering this for the W124.

Whats PP (peach parts?) and FSM?
This post was last modified: 08-18-2010, 12:37 PM by Captain America.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-18-2010, 12:36 PM #60

(08-18-2010, 11:43 AM)winmutt
(08-12-2010, 06:26 PM)garage Yeah looks good, i really wanna flare mine out a bit more.

Its not easy on the W123s. Thick german steel. There is a guy on bw or pp that will rent out the proper tool for doing it. I did mine with a baseball bat and heat gun, this will only allow you to do a little. Somewhere I have the AMG install FSM covering this for the W124.

Whats PP (peach parts?) and FSM?



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Rudolf_Diesel
Ask me if I care...

579
08-18-2010, 12:44 PM #61
(08-18-2010, 12:36 PM)Captain America Whats PP (peach parts?) and FSM?

FSM = Factory Shop Manual

PP = What your mommy asked if you needed to do before you went to bedBig GrinBig Grin

1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.
Rudolf_Diesel
08-18-2010, 12:44 PM #61

(08-18-2010, 12:36 PM)Captain America Whats PP (peach parts?) and FSM?

FSM = Factory Shop Manual

PP = What your mommy asked if you needed to do before you went to bedBig GrinBig Grin


1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.

Captain America
Boostin' & Roostin'

2,221
08-18-2010, 01:05 PM #62
(08-18-2010, 12:44 PM)Rudolf_Diesel
(08-18-2010, 12:36 PM)Captain America Whats PP (peach parts?) and FSM?

FSM = Factory Shop Manual

PP = What your mommy asked if you needed to do before you went to bedBig GrinBig Grin

All life's Important questions have been answered! Cool


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-18-2010, 01:05 PM #62

(08-18-2010, 12:44 PM)Rudolf_Diesel
(08-18-2010, 12:36 PM)Captain America Whats PP (peach parts?) and FSM?

FSM = Factory Shop Manual

PP = What your mommy asked if you needed to do before you went to bedBig GrinBig Grin

All life's Important questions have been answered! Cool



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

winmutt
bitbanger

3,468
08-18-2010, 02:40 PM #63
(08-18-2010, 12:36 PM)Captain America
(08-18-2010, 11:43 AM)winmutt
(08-12-2010, 06:26 PM)garage Yeah looks good, i really wanna flare mine out a bit more.

Its not easy on the W123s. Thick german steel. There is a guy on bw or pp that will rent out the proper tool for doing it. I did mine with a baseball bat and heat gun, this will only allow you to do a little. Somewhere I have the AMG install FSM covering this for the W124.

Whats PP (peach parts?) and FSM?

Peach parts. Shop manual.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-18-2010, 02:40 PM #63

(08-18-2010, 12:36 PM)Captain America
(08-18-2010, 11:43 AM)winmutt
(08-12-2010, 06:26 PM)garage Yeah looks good, i really wanna flare mine out a bit more.

Its not easy on the W123s. Thick german steel. There is a guy on bw or pp that will rent out the proper tool for doing it. I did mine with a baseball bat and heat gun, this will only allow you to do a little. Somewhere I have the AMG install FSM covering this for the W124.

Whats PP (peach parts?) and FSM?

Peach parts. Shop manual.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

garage
Bush Taxi

893
08-19-2010, 04:48 PM #64
Winmutt, do you happen to remember the user name of this guy?

Capt, if your down, ill split the cost of renting the tool with you, and we could try that..?

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-19-2010, 04:48 PM #64

Winmutt, do you happen to remember the user name of this guy?

Capt, if your down, ill split the cost of renting the tool with you, and we could try that..?


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

winmutt
bitbanger

3,468
08-19-2010, 05:18 PM #65
It was in the tool rental section I think. Maybe ask on those boards if someone has it for rent? You should be able to find it at any decent local body shop.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-19-2010, 05:18 PM #65

It was in the tool rental section I think. Maybe ask on those boards if someone has it for rent? You should be able to find it at any decent local body shop.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
08-19-2010, 05:31 PM #66
sure, im willing to try it.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-19-2010, 05:31 PM #66

sure, im willing to try it.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

garage
Bush Taxi

893
08-20-2010, 01:36 AM #67
http://tom.actionfit.com/fenderolling.html
Is this it Winmutt?

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-20-2010, 01:36 AM #67

http://tom.actionfit.com/fenderolling.html
Is this it Winmutt?


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

winmutt
bitbanger

3,468
08-20-2010, 05:37 AM #68
That is the proper tool. Make many passes with small effects.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-20-2010, 05:37 AM #68

That is the proper tool. Make many passes with small effects.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
08-20-2010, 10:08 AM #69
Yeah, Those things are nice


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-20-2010, 10:08 AM #69

Yeah, Those things are nice



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

winmutt
bitbanger

3,468
08-20-2010, 10:22 AM #70
Post locally on CL or local tuner boards. There is a guy here that does it $50 per wheel in your driveway....

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-20-2010, 10:22 AM #70

Post locally on CL or local tuner boards. There is a guy here that does it $50 per wheel in your driveway....


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
08-20-2010, 10:26 AM #71
Wow! I'd do that for sure!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-20-2010, 10:26 AM #71

Wow! I'd do that for sure!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

meareweird
TA 0301

70
08-22-2010, 02:44 PM #72
Those bundt wheels look hot when black! Never thought of that before, if I ever get them I will do the same.
meareweird
08-22-2010, 02:44 PM #72

Those bundt wheels look hot when black! Never thought of that before, if I ever get them I will do the same.

Captain America
Boostin' & Roostin'

2,221
08-23-2010, 02:50 PM #73
(08-22-2010, 02:44 PM)meareweird Those bundt wheels look hot when black! Never thought of that before, if I ever get them I will do the same.

Yeah they turned out waaaaaay better than I had hoped. Wait till I get pics up of the clean wheels...


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-23-2010, 02:50 PM #73

(08-22-2010, 02:44 PM)meareweird Those bundt wheels look hot when black! Never thought of that before, if I ever get them I will do the same.

Yeah they turned out waaaaaay better than I had hoped. Wait till I get pics up of the clean wheels...



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
Boostin' & Roostin'

2,221
08-24-2010, 01:35 AM #74
Did some crap over the weekend...

The Tank and the Parts Car (Blue Thunder) meet. The parts car makes the tank look like a car that could win a best in show award.

   

   

   

Took the radiator from the parts car and swapped it into the tank because there was a leak where the plastic was attached to the alum. core.

   

   

   

   

Did NOT &*@$^@% get the bad ground figured out.

Blew one of the heater hoses doing 80mph on the freeway which pegged the temp gauge within seconds.

Switched the feed and return fuel line which resulted in more power and less smoke.

Finally changed the oil and filter.

Met up with Garage and Stan Because we all missed the cruise on Saturday. (non of us would have mad it anyway). We are like the three freaking stooges.... Garage and I met up with Stan to drop off a couple wheels from the parts car because he keep popping tires. So we get there and he puts the tire on. Garage's battery is dead so he's not starting, And my ground is no good so I'm not starting either. Stan starts Garage and then they both team up to start me lol. Then while Garage and I are on the way home my hose blows so we pull off the freeway to figure out whats up and while waiting for AAA, Garage shuts his car off. The battery is now beyond dead so we have to bump start. Guess he gets the alt from the parts car lol... What a mess we all were!

Garage on left, Stan on right.

   

   

   

   

Got This Sweet little 4 channel x 100 watt amp I'll be using for the front and rear speakers; Plus a digital voltage meter and two temp meters. Each meter has two sensors so I plan to use them to read water and air temps (before and after cooler) when the A/W Intercooler is done.

   

   

   

   
This post was last modified: 08-24-2010, 01:43 AM by Captain America.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-24-2010, 01:35 AM #74

Did some crap over the weekend...

The Tank and the Parts Car (Blue Thunder) meet. The parts car makes the tank look like a car that could win a best in show award.

   

   

   

Took the radiator from the parts car and swapped it into the tank because there was a leak where the plastic was attached to the alum. core.

   

   

   

   

Did NOT &*@$^@% get the bad ground figured out.

Blew one of the heater hoses doing 80mph on the freeway which pegged the temp gauge within seconds.

Switched the feed and return fuel line which resulted in more power and less smoke.

Finally changed the oil and filter.

Met up with Garage and Stan Because we all missed the cruise on Saturday. (non of us would have mad it anyway). We are like the three freaking stooges.... Garage and I met up with Stan to drop off a couple wheels from the parts car because he keep popping tires. So we get there and he puts the tire on. Garage's battery is dead so he's not starting, And my ground is no good so I'm not starting either. Stan starts Garage and then they both team up to start me lol. Then while Garage and I are on the way home my hose blows so we pull off the freeway to figure out whats up and while waiting for AAA, Garage shuts his car off. The battery is now beyond dead so we have to bump start. Guess he gets the alt from the parts car lol... What a mess we all were!

Garage on left, Stan on right.

   

   

   

   

Got This Sweet little 4 channel x 100 watt amp I'll be using for the front and rear speakers; Plus a digital voltage meter and two temp meters. Each meter has two sensors so I plan to use them to read water and air temps (before and after cooler) when the A/W Intercooler is done.

   

   

   

   



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

JB3
Superturbo

1,795
08-24-2010, 07:19 AM #75
hahaha, You guys are funny.

The only thing that would have improved that would be if garage and stan swapped batteries while the cars were running for a nice charge up on stans wagon.
You all remind me of myself getting various unroadworthy craigslist purchases back to my place.

I like those two guys in the background, you can almost read their minds. "WTF are these guys doing?"

You should switch to some wider hose clamps on the radiator, lots of people have had problems with the narrow MB clamps causing neck failures on the radiators. (although mine failed with a wide clamp 300 miles after I put it on, but the radiator was tired anyway. might just be age related)
This post was last modified: 08-24-2010, 07:20 AM by JB3.

1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

JB3
08-24-2010, 07:19 AM #75

hahaha, You guys are funny.

The only thing that would have improved that would be if garage and stan swapped batteries while the cars were running for a nice charge up on stans wagon.
You all remind me of myself getting various unroadworthy craigslist purchases back to my place.

I like those two guys in the background, you can almost read their minds. "WTF are these guys doing?"

You should switch to some wider hose clamps on the radiator, lots of people have had problems with the narrow MB clamps causing neck failures on the radiators. (although mine failed with a wide clamp 300 miles after I put it on, but the radiator was tired anyway. might just be age related)


1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

Captain America
Boostin' & Roostin'

2,221
08-24-2010, 11:05 AM #76
Dude you should have seen us! And I didn't get a picture when Garage had jumpers from his car to the battery in my trunk and Stan had jumpers from his car to the starter in mine, It was comedy looking. Haha those people were like" oh, you guys brought the whole crew out to change the tire huh?"

The problem is that we all thought we were roadworthy!

What do you mean by neck failure? Like the plastic part of the neck cracks or something? I could see that I guess, the wider clamps would distribute the load more evenly.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-24-2010, 11:05 AM #76

Dude you should have seen us! And I didn't get a picture when Garage had jumpers from his car to the battery in my trunk and Stan had jumpers from his car to the starter in mine, It was comedy looking. Haha those people were like" oh, you guys brought the whole crew out to change the tire huh?"

The problem is that we all thought we were roadworthy!

What do you mean by neck failure? Like the plastic part of the neck cracks or something? I could see that I guess, the wider clamps would distribute the load more evenly.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

JB3
Superturbo

1,795
08-24-2010, 11:20 AM #77
this is what I mean by neck failure. The old plastic gets really crumbly and saturated looking after 30 years. Mine looked more like graham cracker than plastic-

   
This post was last modified: 08-24-2010, 11:22 AM by JB3.

1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

JB3
08-24-2010, 11:20 AM #77

this is what I mean by neck failure. The old plastic gets really crumbly and saturated looking after 30 years. Mine looked more like graham cracker than plastic-

   


1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

Captain America
Boostin' & Roostin'

2,221
08-24-2010, 12:29 PM #78
(08-24-2010, 11:20 AM)dropnosky this is what I mean by neck failure. The old plastic gets really crumbly and saturated looking after 30 years. Mine looked more like graham cracker than plastic-

Holy crud! That's no good. The newly installed radiator looks to be somewhat new, so I'm hoping that doesn't happen anytime soon.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-24-2010, 12:29 PM #78

(08-24-2010, 11:20 AM)dropnosky this is what I mean by neck failure. The old plastic gets really crumbly and saturated looking after 30 years. Mine looked more like graham cracker than plastic-

Holy crud! That's no good. The newly installed radiator looks to be somewhat new, so I'm hoping that doesn't happen anytime soon.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
Boostin' & Roostin'

2,221
08-24-2010, 10:35 PM #79
   

I love Parts Geek! Ordered yesterday and my stuff arrived today. Big Grin

While I'm replacing all the hoses I want to replace all the freeze plugs. Anyone know how many there are? I only see four. And the two that are leaking are behind the oil filter housing and the injection pump Dodgy I got a new oil filter housing gasket to do that one, but i guess the question I have is how difficult is it to pull the injection pump and re-install it? Are there any adjustments that I should make while its out? Any tricks you guys can share? Rudolf??? I know you have done yours a couple times...


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-24-2010, 10:35 PM #79

   

I love Parts Geek! Ordered yesterday and my stuff arrived today. Big Grin

While I'm replacing all the hoses I want to replace all the freeze plugs. Anyone know how many there are? I only see four. And the two that are leaking are behind the oil filter housing and the injection pump Dodgy I got a new oil filter housing gasket to do that one, but i guess the question I have is how difficult is it to pull the injection pump and re-install it? Are there any adjustments that I should make while its out? Any tricks you guys can share? Rudolf??? I know you have done yours a couple times...



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

willbhere4u
Six in a row make her go!

2,507
08-24-2010, 11:14 PM #80
I don't know about the IP

But be careful not to strip the Allen bolt's to the oil filter housing don't ask me how I know!

use a pick tool or some thing to get all of the junk out of the bolt head's first!!!!

you will most probably have to sacrifice an Allen wrench or 2 there are 5 Allen bolt's if I'm not mistaken


This post was last modified: 08-24-2010, 11:15 PM by willbhere4u.

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-24-2010, 11:14 PM #80

I don't know about the IP

But be careful not to strip the Allen bolt's to the oil filter housing don't ask me how I know!

use a pick tool or some thing to get all of the junk out of the bolt head's first!!!!

you will most probably have to sacrifice an Allen wrench or 2 there are 5 Allen bolt's if I'm not mistaken



1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Rudolf_Diesel
Ask me if I care...

579
08-25-2010, 07:16 AM #81
You can remove the rack and make a couple of adjustments referenced in the pump tuning section. It is not that hard to pull the pump, just set thye engine on #1 @ 24* it will be easier to pull when you have the filter housing off. The adjustments are not hard, just takes a little patience - document, document, document is also recommended so you have a reference point to return to.

1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.
Rudolf_Diesel
08-25-2010, 07:16 AM #81

You can remove the rack and make a couple of adjustments referenced in the pump tuning section. It is not that hard to pull the pump, just set thye engine on #1 @ 24* it will be easier to pull when you have the filter housing off. The adjustments are not hard, just takes a little patience - document, document, document is also recommended so you have a reference point to return to.


1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.

Captain America
Boostin' & Roostin'

2,221
08-25-2010, 11:28 AM #82
Cool thanks guys!

Rudolf, I haven't finished reading the tuning guide yet but I started a while back.

Ohhhh how little thing turn into big projects! Undecided One split hose has turned into pulling the IP and tuning! Guess I gotta get that Intercooler and EGT install going....

Ready for some welding rudolf?


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-25-2010, 11:28 AM #82

Cool thanks guys!

Rudolf, I haven't finished reading the tuning guide yet but I started a while back.

Ohhhh how little thing turn into big projects! Undecided One split hose has turned into pulling the IP and tuning! Guess I gotta get that Intercooler and EGT install going....

Ready for some welding rudolf?



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

willbhere4u
Six in a row make her go!

2,507
08-25-2010, 03:27 PM #83
Also check you oil cooler lines at this time!!! it's a lot easier to replace them while your in there!!!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-25-2010, 03:27 PM #83

Also check you oil cooler lines at this time!!! it's a lot easier to replace them while your in there!!!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Captain America
Boostin' & Roostin'

2,221
08-25-2010, 03:32 PM #84
Yeah I want to make some up like what Rudolf did....

The IP un/install and tuning sounds Scary Confused eeek!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-25-2010, 03:32 PM #84

Yeah I want to make some up like what Rudolf did....

The IP un/install and tuning sounds Scary Confused eeek!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

garage
Bush Taxi

893
08-25-2010, 03:43 PM #85
Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-25-2010, 03:43 PM #85

Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Rudolf_Diesel
Ask me if I care...

579
08-25-2010, 04:29 PM #86
(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

If I get my car running this weekend, maybe we can meet up and I can show you how to pull the pumps. The M-pump is much easier - before the supercharger I could pull the pump, adjust it and put it back in ~20 mins. Now it would take a little longer.

The hardest thing about the pump is the bolt/bracket on the rear of the pump - I just left it off after the first time.
This post was last modified: 08-25-2010, 04:30 PM by Rudolf_Diesel.

1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.
Rudolf_Diesel
08-25-2010, 04:29 PM #86

(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

If I get my car running this weekend, maybe we can meet up and I can show you how to pull the pumps. The M-pump is much easier - before the supercharger I could pull the pump, adjust it and put it back in ~20 mins. Now it would take a little longer.

The hardest thing about the pump is the bolt/bracket on the rear of the pump - I just left it off after the first time.


1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.

ForcedInduction
Banned

3,628
08-25-2010, 06:50 PM #87
The pump is pretty easy, its the oil cooler lines I'd be worried about. One stripping can make a fun project sour with the turn of a wrench.
Don't forget the antiseize!
This post was last modified: 08-25-2010, 06:51 PM by ForcedInduction.
Attached Files
Image(s)
   
ForcedInduction
08-25-2010, 06:50 PM #87

The pump is pretty easy, its the oil cooler lines I'd be worried about. One stripping can make a fun project sour with the turn of a wrench.
Don't forget the antiseize!

Attached Files
Image(s)
   

garage
Bush Taxi

893
08-25-2010, 08:15 PM #88
(08-25-2010, 04:29 PM)Rudolf_Diesel
(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

If I get my car running this weekend, maybe we can meet up and I can show you how to pull the pumps. The M-pump is much easier - before the supercharger I could pull the pump, adjust it and put it back in ~20 mins. Now it would take a little longer.

The hardest thing about the pump is the bolt/bracket on the rear of the pump - I just left it off after the first time.

Rudolf..i would be stoked on that!
I would love to come check out your OMG617, and learn somthing while im at it.

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-25-2010, 08:15 PM #88

(08-25-2010, 04:29 PM)Rudolf_Diesel
(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

If I get my car running this weekend, maybe we can meet up and I can show you how to pull the pumps. The M-pump is much easier - before the supercharger I could pull the pump, adjust it and put it back in ~20 mins. Now it would take a little longer.

The hardest thing about the pump is the bolt/bracket on the rear of the pump - I just left it off after the first time.

Rudolf..i would be stoked on that!
I would love to come check out your OMG617, and learn somthing while im at it.


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Captain America
Boostin' & Roostin'

2,221
08-26-2010, 12:08 AM #89
(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

Yeah Eff you and your feather weight four banger! Tongue
(08-25-2010, 04:29 PM)Rudolf_Diesel
(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

If I get my car running this weekend, maybe we can meet up and I can show you how to pull the pumps. The M-pump is much easier - before the supercharger I could pull the pump, adjust it and put it back in ~20 mins. Now it would take a little longer.

The hardest thing about the pump is the bolt/bracket on the rear of the pump - I just left it off after the first time.

As Garage said... That would be awesome. I would love to talk with someone face to face while we are standing there looking at it... That's invaluable knowledge on something like this, who to someone like me who has not done it, seems like one wrong move could leave you with poor running motor or rods hanging out of the block.
(08-25-2010, 06:50 PM)ForcedInduction The pump is pretty easy, its the oil cooler lines I'd be worried about. One stripping can make a fun project sour with the turn of a wrench.
Don't forget the antiseize!

Thanks Forced, I now remember seeing that in one of your posts... That happened when you loosened the fitting? Someone must have installed it buggered....
This post was last modified: 08-26-2010, 12:14 AM by Captain America.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-26-2010, 12:08 AM #89

(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

Yeah Eff you and your feather weight four banger! Tongue
(08-25-2010, 04:29 PM)Rudolf_Diesel
(08-25-2010, 03:43 PM)garage Im nervous to pull my IP to capt, seems like alot can go wrong, or itd be a big pain in the rear to get it reinstalled.

If you tune that pump theres no way imma be able to catch you!! I needa get working on making sure that dosnt happenBig Grin

If I get my car running this weekend, maybe we can meet up and I can show you how to pull the pumps. The M-pump is much easier - before the supercharger I could pull the pump, adjust it and put it back in ~20 mins. Now it would take a little longer.

The hardest thing about the pump is the bolt/bracket on the rear of the pump - I just left it off after the first time.

As Garage said... That would be awesome. I would love to talk with someone face to face while we are standing there looking at it... That's invaluable knowledge on something like this, who to someone like me who has not done it, seems like one wrong move could leave you with poor running motor or rods hanging out of the block.
(08-25-2010, 06:50 PM)ForcedInduction The pump is pretty easy, its the oil cooler lines I'd be worried about. One stripping can make a fun project sour with the turn of a wrench.
Don't forget the antiseize!

Thanks Forced, I now remember seeing that in one of your posts... That happened when you loosened the fitting? Someone must have installed it buggered....



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

ForcedInduction
Banned

3,628
08-26-2010, 08:07 AM #90
(08-26-2010, 12:08 AM)Captain America That happened when you loosened the fitting? Someone must have installed it buggered.

Yes. The hoses appeared to be original though.
ForcedInduction
08-26-2010, 08:07 AM #90

(08-26-2010, 12:08 AM)Captain America That happened when you loosened the fitting? Someone must have installed it buggered.

Yes. The hoses appeared to be original though.

winmutt
bitbanger

3,468
08-26-2010, 09:08 AM #91
The problem with the oil cooler lines is that (iirc) they are only 15ftlb to tighten. Everyone, my self included, over torques them.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
08-26-2010, 09:08 AM #91

The problem with the oil cooler lines is that (iirc) they are only 15ftlb to tighten. Everyone, my self included, over torques them.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
08-26-2010, 10:16 AM #92
(08-26-2010, 09:08 AM)winmutt The problem with the oil cooler lines is that (iirc) they are only 15ftlb to tighten. Everyone, my self included, over torques them.

Gotcha, Things like that are easily over torqued....


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-26-2010, 10:16 AM #92

(08-26-2010, 09:08 AM)winmutt The problem with the oil cooler lines is that (iirc) they are only 15ftlb to tighten. Everyone, my self included, over torques them.

Gotcha, Things like that are easily over torqued....



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

ForcedInduction
Banned

3,628
08-26-2010, 05:20 PM #93
And don't forget that lube (antiseize) increases the torque value with less effort.
ForcedInduction
08-26-2010, 05:20 PM #93

And don't forget that lube (antiseize) increases the torque value with less effort.

Captain America
Boostin' & Roostin'

2,221
08-26-2010, 10:25 PM #94
(08-26-2010, 05:20 PM)ForcedInduction And don't forget that lube (antiseize) increases the torque value with less effort.

Yup. my hope with that is the lub/antiseize with keep the threads from galling like that even with a tad more torque.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-26-2010, 10:25 PM #94

(08-26-2010, 05:20 PM)ForcedInduction And don't forget that lube (antiseize) increases the torque value with less effort.

Yup. my hope with that is the lub/antiseize with keep the threads from galling like that even with a tad more torque.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
Boostin' & Roostin'

2,221
08-27-2010, 10:39 AM #95
(08-24-2010, 11:20 AM)dropnosky this is what I mean by neck failure. The old plastic gets really crumbly and saturated looking after 30 years. Mine looked more like graham cracker than plastic-

Dude, you nailed it!!! Looks like this radiator has already been victimized.

   

And this is a pic of the tail end of the flush...
YUCK!
   


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-27-2010, 10:39 AM #95

(08-24-2010, 11:20 AM)dropnosky this is what I mean by neck failure. The old plastic gets really crumbly and saturated looking after 30 years. Mine looked more like graham cracker than plastic-

Dude, you nailed it!!! Looks like this radiator has already been victimized.

   

And this is a pic of the tail end of the flush...
YUCK!
   



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Rudolf_Diesel
Ask me if I care...

579
08-29-2010, 09:40 PM #96
You guys are bad mojo for charging systemsBig Grin I ended up having to get a new alternator.

I had to drive about 50 miles home with just battery for lights, about 10 miles from home it was like driving with candles for head lights...So it occurred to me that electric fans do not work without power DUH!Rolleyes - good thing it was a cool night.

So I replaced the electric with a regular old fan.
This post was last modified: 08-29-2010, 09:42 PM by Rudolf_Diesel.

1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.
Rudolf_Diesel
08-29-2010, 09:40 PM #96

You guys are bad mojo for charging systemsBig Grin I ended up having to get a new alternator.

I had to drive about 50 miles home with just battery for lights, about 10 miles from home it was like driving with candles for head lights...So it occurred to me that electric fans do not work without power DUH!Rolleyes - good thing it was a cool night.

So I replaced the electric with a regular old fan.


1982 300SD: 304,xxx Super M-pump with 7.5mm elements, 265 Nozzles, GT35 water cooled turbo, M90 Supercharger, A/W Intercooler, Serpentine drive belt, 3" SS exhaust with Magnaflow muffler, 240 breather, AEM dry Filter, Manual Boost Control, EGT / Boost / EMP gauges....Moved on to other projects

1995 F-350 7.3L PSD: 230,xxx 6.0 IC, DIY Stage 1 Injectors, 17* hpop, Tony Wildman Chip, John Wood Trans, 6.4L TC, 3" down pipe, 4" straight exhaust, 310 HP on wheel dyno - 8500# dually: 0-60 in 6.98

Suzuki Samurai: VW 1.9L TD, Trackick doubler transfer case (made by me) 5.8:1 transfer case gears, YJ springs front and rear with rear missing links, wheel base extended 14", diffs welded, some day a VNT.

Captain America
Boostin' & Roostin'

2,221
08-30-2010, 01:14 AM #97
(08-29-2010, 09:40 PM)Rudolf_Diesel You guys are bad mojo for charging systemsBig Grin I ended up having to get a new alternator.

(08-29-2010, 09:40 PM)Rudolf_Diesel I had to drive about 50 miles home with just battery for lights, about 10 miles from home it was like driving with candles for head lights...So it occurred to me that electric fans do not work without power DUH!Rolleyes - good thing it was a cool night.

Yeah you shouldn't have really needed it.

(08-29-2010, 09:40 PM)Rudolf_Diesel So I replaced the electric with a regular old fan.
DUH!Rolleyes - good thing it was a cool night.

Awe Undecided

Rudolf came to my house to help me with my IP, He is an awesome guy ... way cool. It got pulled off, removed the rack limiter, adjusted the torque capsule a half turn and bolted her back up. She runs real well. Not a great deal, but more noticeable power everywhere. Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

What also helped was tweaking the throttle linkage so it was against the stop on the pump when my foot was to the floor.

Everything adds up I guess.

I need to order new injector return lines as mine are shot. Those should come tomorrow with some other goodies.
This post was last modified: 08-30-2010, 01:15 AM by Captain America.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-30-2010, 01:14 AM #97

(08-29-2010, 09:40 PM)Rudolf_Diesel You guys are bad mojo for charging systemsBig Grin I ended up having to get a new alternator.

(08-29-2010, 09:40 PM)Rudolf_Diesel I had to drive about 50 miles home with just battery for lights, about 10 miles from home it was like driving with candles for head lights...So it occurred to me that electric fans do not work without power DUH!Rolleyes - good thing it was a cool night.

Yeah you shouldn't have really needed it.

(08-29-2010, 09:40 PM)Rudolf_Diesel So I replaced the electric with a regular old fan.
DUH!Rolleyes - good thing it was a cool night.

Awe Undecided

Rudolf came to my house to help me with my IP, He is an awesome guy ... way cool. It got pulled off, removed the rack limiter, adjusted the torque capsule a half turn and bolted her back up. She runs real well. Not a great deal, but more noticeable power everywhere. Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

What also helped was tweaking the throttle linkage so it was against the stop on the pump when my foot was to the floor.

Everything adds up I guess.

I need to order new injector return lines as mine are shot. Those should come tomorrow with some other goodies.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

garage
Bush Taxi

893
08-30-2010, 10:02 PM #98
(08-30-2010, 01:14 AM)Captain America Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

How about the idle adjust screw, that would be the first thing i would try to mess with if trying to get her back to idle sooner..

And yes every liiiiil bit helpsSmile
This post was last modified: 08-30-2010, 11:00 PM by garage.

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-30-2010, 10:02 PM #98

(08-30-2010, 01:14 AM)Captain America Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

How about the idle adjust screw, that would be the first thing i would try to mess with if trying to get her back to idle sooner..

And yes every liiiiil bit helpsSmile


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Captain America
Boostin' & Roostin'

2,221
08-30-2010, 10:51 PM #99
(08-30-2010, 10:02 PM)garage
(08-30-2010, 01:14 AM)Captain America Awe Undecided

Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

How about the idle adjust screw, that would be the first thing i would try to mess with if trying to get her back to idle sooner..

And yes every liiiiil bit helpsSmile

Idk, But these injector return lines are pissin me off! they wont stop leaking. On the way home today she tried to overheat on me... I think the thermostat stuck closed. I took it out and filled back up with water and she was still running warm on the way home on the freeway (100C shown on the gauge) which I verified to be accurate.
This post was last modified: 08-30-2010, 10:52 PM by Captain America.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-30-2010, 10:51 PM #99

(08-30-2010, 10:02 PM)garage
(08-30-2010, 01:14 AM)Captain America Awe Undecided

Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

How about the idle adjust screw, that would be the first thing i would try to mess with if trying to get her back to idle sooner..

And yes every liiiiil bit helpsSmile

Idk, But these injector return lines are pissin me off! they wont stop leaking. On the way home today she tried to overheat on me... I think the thermostat stuck closed. I took it out and filled back up with water and she was still running warm on the way home on the freeway (100C shown on the gauge) which I verified to be accurate.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

garage
Bush Taxi

893
08-30-2010, 11:01 PM #100
(08-30-2010, 10:51 PM)Captain America
(08-30-2010, 10:02 PM)garage
(08-30-2010, 01:14 AM)Captain America Awe Undecided

Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

How about the idle adjust screw, that would be the first thing i would try to mess with if trying to get her back to idle sooner..

And yes every liiiiil bit helpsSmile

Idk, But these injector return lines are pissin me off! they wont stop leaking. On the way home today she tried to overheat on me... I think the thermostat stuck closed. I took it out and filled back up with water and she was still running warm on the way home on the freeway (100C shown on the gauge) which I verified to be accurate.

Well luckily you have parts comin right!

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
08-30-2010, 11:01 PM #100

(08-30-2010, 10:51 PM)Captain America
(08-30-2010, 10:02 PM)garage
(08-30-2010, 01:14 AM)Captain America Awe Undecided

Slightly slow to return to idle, easiest to describe as there is no engine braking at all. Now that the hard part has been taken care of I will make some more adjustments as I finish reading the adjustment thread...

How about the idle adjust screw, that would be the first thing i would try to mess with if trying to get her back to idle sooner..

And yes every liiiiil bit helpsSmile

Idk, But these injector return lines are pissin me off! they wont stop leaking. On the way home today she tried to overheat on me... I think the thermostat stuck closed. I took it out and filled back up with water and she was still running warm on the way home on the freeway (100C shown on the gauge) which I verified to be accurate.

Well luckily you have parts comin right!


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

Pages (10): Previous 1 2 3 4 5 10 Next  
 
  • 6 Vote(s) - 3.83 Average
Users browsing this thread:
 4 Guest(s)
Users browsing this thread:
 4 Guest(s)