+- STD (https://www.superturbodiesel.com/std)
+-- Forum: Tuning (https://www.superturbodiesel.com/std/forumdisplay.php?fid=6)
+--- Forum: Engine (https://www.superturbodiesel.com/std/forumdisplay.php?fid=7)
+--- Thread: EATON M112 AND ????? TURBO (/showthread.php?tid=3901)
EATON M112 AND ????? TURBO - mantahead - 09-05-2012
Hi,
for my new drift car i would like at least 500bhp, i am going to force feed the turbo intake with the eaton m112 and then use a bypass valve when the blower runs out of steam. This is the om606 engine.
I like the holset hx35 i used before(OM605), although it was slow to spool. It will be too small now anyway.
I want it to spool as fast as possible, the question is: what turbo?
Is a hx55 too big?
RE: EATON M112 AND ????? TURBO - Siekkinen - 09-06-2012
Hx52 pro is fine.
RE: EATON M112 AND ????? TURBO - mantahead - 09-06-2012
hi,
is there many different exhaust housings?
what size of housing?
(09-06-2012, 03:14 PM)Siekkinen Hx52 pro is fine.
RE: EATON M112 AND ????? TURBO - mantahead - 11-14-2012
hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
RE: EATON M112 AND ????? TURBO - Turbo - 11-14-2012
Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at all
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
RE: EATON M112 AND ????? TURBO - mantahead - 11-14-2012
(11-14-2012, 06:28 PM)Turbo Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at allwhat kinda power would the hx50 make?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
the charger should speed up the spool up hopefully.
RE: EATON M112 AND ????? TURBO - Turbo - 11-15-2012
I ask for a turbo suggestions for +600hk and Pekka gave that suggestion, I never tried it since I am retuning and building the engine for higher purpose
quote='mantahead' pid='45982' dateline='1352936351']
(11-14-2012, 06:28 PM)Turbo Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at allwhat kinda power would the hx50 make?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
the charger should speed up the spool up hopefully.
[/quote]
RE: EATON M112 AND ????? TURBO - EDH_Performance - 11-16-2012
I am going to use a hx52 with billet wheel and 16cm2 exhousing in a compound setup on mye engine
RE: EATON M112 AND ????? TURBO - Siekkinen - 11-17-2012
hx50 can make more than 500 horsepower. Don't know how much more but 600 horsepower could be possible with it.